Canon 5dsr Manual

31
Nomenclature
Viewfinder Information
* The display will show only the settings currently applied.
Electronic level (p.75)
Spot metering circle (p.213)
Grid (p.74)
White balance (p.174)
< > Battery 
level (p.48)
Drive mode (p.142)
AF operation (p.86)
Metering mode (p.212)JPEG/RAW (p.149)
Focusing screen
 Single AF point
< O > Spot AF point 
(p.95)
Flicker detection 
(p.191)
<
z > Warning symbol 
(p.409)
Area AF frame 
(p.91, 97)
Aspect ratio 
line (1:1)
Crop area (1.6x)
Crop area (1.3x) 

Nomenclature
32
 AE lock (p.217) 
AEB in-progress 
(p.215)
< D > Flash-ready 
(p.244) 
Improper FE lock 
warning
< d > FE lock (p.244)
FEB in-progress (p.251)
< e> High-speed sync (p.251)
< y > Flash exposure 
compensation (p.244)
Shutter speed (p.206)
FE lock ( FEL)
Busy ( buSY)
Multi function lock warning ( L)
No card warning ( Card)
Error code (Err )
Aperture (p.208) AF point selection
(
[ ] AF, SEL [ ], SEL AF )
AF point registration
( [ ] HP, SEL [ ], SEL HP )
Card warning ( Card 1/2)
Card full...

33
Nomenclature
Mode Dial
You can set the shooting mode. Turn the Mode Dial while holding down 
the Mode Dial center (Mode Dial lock release button).
A : Scene Intelligent Auto (p.80)
F
: Bulb (p.218)
a : Manual exposure (p.210)
f : Aperture-priority AE (p.208)
s : Shutter-priority AE (p.206)
d : Program AE (p.204)
Custom shooting mode
You can register the shooting mode ( d/s /f /a/F), AF 
operation, menu settings, etc., to  w, x , y Mode Dial positions 
(p.437). 

Nomenclature
34
Battery Charger LC-E6
Charger for Battery Pack LP-E6N/LP-E6 (p.40).
Battery Charger LC-E6E
Charger for Battery Pack LP-E6N/LP-E6 (p.40).
Battery pack slot
Charge lamp
Power plug
IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS.
DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, 
CAREFULLY FOLLOW THESE INSTRUCTIONS.
For connection to a supply not in the U.S.A., use an attachment plug adapter 
of the proper configuration for the power outlet, if needed.
Power cord 
Power cord socket...

35
Nomenclature
Pass the end of the strap through the 
camera’s strap mount eyelet from the 
bottom. Then pass it through the strap’s 
buckle as shown in the illustration. Pull the 
strap to take up any slack and make sure the 
strap will not loosen from the buckle.
The eyepiece cover is also attached to 
the strap (p.236).
Attaching the Strap
Eyepiece cover 

Nomenclature
36
When connecting the camera to a computer, printer, Wireless File 
Transmitter or GPS Receiver, use the provided interface cable or one 
from Canon (shown in the System Map on page 454).
When connecting the interface cable,  also use the provided cable 
protector. Using the cable protector prevents the cable from accidental 
disconnection and the terminal from getting damaged.
Using the Provided Interface Cable and a Genuine HDMI Cable 
(sold separately)
Using the Cable Protector
Provided...

37
Nomenclature
Using a Genuine Interface Cable (sold separately)
If you use a genuine interface cable (sold 
separately, p.454), run the cable through the 
clamp before attaching the clamp to the cable 
protector.
Clamp
Connecting interface cable without using the cable protector may 
damage the digital terminal.
 Do not use a USB 2.0 cable equipped with a Micro-B plug. It may 
damage the camera’s digital terminal.
 As shown in the lower-right illustration  for step 4, check that the interface 
cable...

38 

39
1
Getting Started
This chapter explains preparatory steps before you start 
shooting and basic camera operations. 

40
1Remove the protective cover.
Detach the protective cover provided 
with the battery.
2Attach the battery.
As shown in the illustration, attach the 
battery securely to the charger.
 To detach the battery, follow the 
above procedure in reverse.
3Recharge the battery.
For LC-E6
As shown by the arrow, flip out the 
battery charger’s prongs and insert 
the prongs into a power outlet.
For LC-E6E
Connect the power cord to the 
charger and insert the plug into a 
power outlet. 
 Recharging starts...