Candy Cdcf 6 Instruction Manual

							9WARNING! 
 
						

							10About Electricity Connecting
.
Insure proper ground 
exists before use
CAUTION , for personal safety:
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD GROUNDING PRONG FROM THE POWER CORD.
Electrical Requirements  
This dishwasher is designed for operation on an adequately wired individual 220~240VAC,50~60HZ. Use required fuse 10 amp. 
Fused electrical supply is required-copper wire only. Time delay fuse or circuit breaker recommended and provide separate
circuit serving only this appliance. Outlet should be placed in adjacent cabinet.Make sure that plug on the appliance remains 
eccessible after installation. Remove the power cord plug from the wall receptacle.
Disconnect Unicouple from faucet adapter.
NOTE : When motor stops at the end of the final rinse, the Unicouple can be dis\
connected  and returned to storage.
21
How to Disconnect the Dishwasher
WARNING! 
How to Connect the safety supply hose
Pull The  supply hoses completely out from storage compartment located a\
t rear of dishwasher.
Turn water fully on before starting the dishwasher.
1 Tighter the screws of the safety supply hose to the faucet with thread 3\
/4inch.
Turn off the water.
Release the water pressure by depressing the pressure release button. Th\
is relieves water pressure and protects  you, and the
 room, from severe splashing.
Unscrew  The safety supply hose  from the faucet..
3 2
1
How to Disconnect the safety supply hose 2
3 The appliance must be connected to the water mains using new hose-sets. 
The old hose-sets should not be reused.
Water pressure must be between 0,04 MPa and 1 MPa. If the pressure is below the minimum 
consult our Service Department for advice.
 
						

							11How to Drain Excess Water 
From Unicouple Hoses
If the sink is 34 or higher from the floor, the excesswater in Unicouple\
 hoses
cannot be drained directly into the sink. It will be necessary to drain \
excess
water from hoses into a bowl or suitable container that is heldoutside a\
nd lower
 than the sink.
Positioning the Appliance Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent 
cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to 
facilitate proper installation. 
COLD WATER CONNECTION
HOT  WATER CONNECTION Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time, let the water  run to make sure that the 
water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and 
damage the appliance.
The water supply to the appliance can also be connected to the house hot  water line  (centralized system, heating system),
as long as  it does not exceed a temperature of 60 C. In this case, the wash cycle time will be shortened by about 15 minutes
and the wash  efficiency slightly reduced.
The connection must be made to the hot water line following the same procedures as those  for the connection to the
cold water line.
 
						

							12Problem
Possible Causes What To Do
Fuse blown, or the
circuit breaker acted Replace fuse or reset circuit breaker. Remove any other 
appliances sharing the same circuit with the dishwasher
NoiseSound from soft food shredding action and detergent cup
opening.
Utensils are not secure
in the baskets or something
small has dropped into
the basket To ensure everything is secured in the dishwasher.
Motor hums Dishwasher has not been used regularly. If you do not use it 
often, remember to set it to fill and pump out every week, 
which will help keep the seal moist.
Before  Calling  for  service . . .
Troubleshooting Tips
Review the charts on the following pages may make you  be free of calling for service.
Suds in the tub
Improper detergentAdd 4 litres of cold water to the tub. Close and latch the 
dishwasher, then drain out the water by slowly turning the
Dial until a drain period is reached. Repeat if necessary.
Spilled rinse agent Always wipe up rinse agent
spills immediately.
Stained tub interiorDetergent with
colorant was usedMake sure that the detergent is the one without colorant.
Rinse agent dispenser
is empty Make sure that the rinse agent dispense is filled.
Dishes and flatware
not cleanImproper program
Improper rack loading Make sure that the action of the detergent dispenser and  spray arms are not blocked by large dishware.
Spots and filming
on glasses and flatwareExtremely hard water
Low inlet  
temperature
Overloading the 
dishwasher
Improper loading
Old or damp powder
detergent
Empty rinse agent 
dispenser
Incorrect dosage of 
 detergent To remove spots from glassware:
1 Take out all metal utensils out of the dishwasher.
Do not add detergent.
Choose the longest cycle.
Start the dishwasher and allow it to run for about 
18 to 22 minutes, then it will be in the main wash.
Open the door to pour 2 cups of white vinegar 
into the bottom of the dishwasher.
Close the door and let the dishwasher complete
 the cycle. If the vinegar  does not work: Repeat 
as above, except use 1/4 cup (60 ml)of citric acid 
crystals instead of vinegar.
2
3
4
5
6
Some audible sounds are
normal
Dishwasher doesn t run
Dishes are not dried
Drain pump doesn t stop Select stronger program
1 
2
3
45
6 7
Use only the special dishwasher detergent to avoid suds.If this occurs, open the dishwasher and let suds evaporate.
 
						

							13Before  calling  for  service . . .
Problem
Possible Causes What To Do
Cloudiness on
 glasswareCombination of soft
water and too much
detergent Use less detergent if you have soft water and select a 
shortest cycle to wash the glassware and to get them clean. 
Yellow o r b rown f ilm
on inside surfacesTea or coffee stains using a solution of 1/2 cup of bleach and 3 cups warm water
to remove the stains by hand. 
WARNING
You have to wait for 20 minutes after a cycle to let the heating
elements cool down before cleaning interior; otherwise, burns 
will happen.
Iron deposits in water
can cause an overall film You have to call a water softener company for a special filter.
White film on inside 
surfaceHard water minerals To clean the interior, use a damp sponge with dishwasher 
detergent and wear rubber gloves. Never use any other cleaner
than dishwasher detergent for the risk of foaming or suds.  Dial is not in the 
OFF
position  Turn the Dial to OFF position and slide the door latch to the
left.
Detergent left in
dispenser cupsDishes block detergent 
cups Re-loading the dishes properly.
SteamNormal phenomenon
There is some steam coming through the vent by the door 
latch during drying and water draining.
Black or gray
marks on dishesAluminum utensils have
rubbed against dishes Use a mild abrasive cleaner to eliminate those marks.
Detergent cup lid
won t latch
Water standing inThis is normal A small amount of clean water around the outlet on 
the tub bottom at the back of the tub keeps the water 
seal lubricated.
the bottom of the tub
Dishwasher leaks Overfill dispenser or rinse
aid spills