Brother Laserprinter Hl 1650 1670n User Guide

CHAPTER 1 ABOUT THIS PRINTER
1-31
P P
r r
i i
n n
t t
i i
n n
g g
   
o o
n n
   
L L
a a
b b
e e
l l
s s
, ,
   
T T
r r
a a
n n
s s
p p
a a
r r
e e
n n
c c
i i
e e
s s
   
e e
t t
c c
. .
Special paper types to avoid
•Damaged, curled, wrinkled, or irregularly shaped paper
Fig. 1-22 

1-32
✒
✒✒ ✒  Note
•Before using paper with holes, such as organizer sheets, you must fan
the stack of paper well to avoid paper jams and misfeeds.
•Do not use paper with perforations at the edge.
•Do not place the punched holes of organizer sheets near the actuator
(paper sensor).
•Do not use organizer sheets that are stuck together. The glue on them
might cause damage to the printer.
•Do not load different types of paper at the same time in the paper
cassette because it may cause paper jams or...

CHAPTER 1 ABOUT THIS PRINTER
1-33
☛
☛☛ ☛ 1.Open the Multi-purpose tray.
Fig. 1-23
☛
☛☛ ☛ 2.Unfold the Multi-purpose tray extension.
Fig. 1-24 

1-34
When you use labels, open the Face up output tray.
When you use transparencies, print to the Face down output tray.
Fig. 1-25
☛
☛☛ ☛ 3.Place paper in the Multi-purpose tray so it touches the back of the tray and
remains below the limit mark.
Fig. 1-26
✒
✒✒ ✒  Note
When you place paper in the Multi-purpose tray, note the following:
•If you will be printing on paper that weighs more than 135 g/m2  (36 lbs),
use the face up output tray.
•Insert the leading edge of the paper first and push it gently...

CHAPTER 1 ABOUT THIS PRINTER
1-35
☛
☛☛ ☛ 4.Press and slide the paper width adjuster to fit the paper.
Fig. 1-27 

1-36
☛
☛☛ ☛ 5.Change the following settings in the printer driver Properties tab.


Select the
envelope size,
media t
ype etc.
Select the
envelo
pe size.
Select the Multi-purpose
tra
y.
Select the Multi-purpose
tra
y. 

CHAPTER 1 ABOUT THIS PRINTER
1-37
P P
r r
i i
n n
t t
i i
n n
g g
   
t t
o o
   
t t
h h
e e
   
F F
a a
c c
e e
   
u u
p p
   
o o
u u
t t
p p
u u
t t
   
t t
r r
a a
y y
   
( (
F F
a a
c c
e e
   
u u
p p
p p
r r
i i
n n
t t
i i
n n
g g
) )
When the Face up output tray is open, the printer has a straight paper path from the
Paper cassette or Multi-purpose tray to the rear of the printer. Use this output method
when you want to print on special media that is thick or should not be bent, such as
heavy...

1-38
☛
☛☛ ☛ 3.Place the paper into the Paper cassette or Multi-purpose tray.
Fig. 1-30
☛
☛☛ ☛ 4.After the printer ejects all the printed pages, remove them and close the
Face up output tray. 

CHAPTER 1 ABOUT THIS PRINTER
1-39
P P
r r
i i
n n
t t
i i
n n
g g
   
o o
n n
   
b b
o o
t t
h h
   
s s
i i
d d
e e
s s
   
o o
f f
   
t t
h h
e e
   
p p
a a
p p
e e
r r
   
( (
D D
u u
p p
l l
e e
x x
p p
r r
i i
n n
t t
i i
n n
g g
) )
The supplied printer drivers for Windows® 95 / 98 / Me, Windows NT® 4.0,
Windows® 2000 supports automatic duplex printing.
Guidelines for printing on both sides of the paper
1  If the paper is thin, it may wrinkle.
2  If paper is curled, straighten it, and then place...

1-40
☛
☛☛ ☛ 1.Load paper into the Paper cassette or Multi-purpose tray.
 
 
 
 
 
 
Fig. 1-31
 
 
 
☛
☛☛ ☛ 2.When you use A4 or Letter size paper, set the Paper adjustment lever for
duplex printing to match your paper size.
 
 
 
 
 
 
Fig. 1-32
 
 
 
✒
✒✒ ✒  Note
If the Paper adjustment lever for duplex printing is not correctly set for the
paper size, paper jams may occur and the printing will be out of position on
the paper.