Brother HL 2132R User Manual

Control Panel 
57
3
 FRONT COVER OPEN
Close the front cover of the machine.
FUSER COVER OPEN
Close the fuser cover located behind the back cover of the machine.
JAM TRAY 1 / JAM INSIDE / JAM REAR / JAM DUPLEX
Clear the paper jam. See Paper jams and how to clear them on page 105. If the 
machine does not start printing, press Go.
MEMORY FULL
The machine memory is full and the machine cannot print full pages of a document. 
See Solving print problems on page 119. 
PRINT OVERRUN
A print overrun occurred and...

Control Panel 
58
3
Service call indications3
If there is an error that cannot be cleared by the user, the machine will show that a service call is needed by 
lighting up all the LEDs as shown below.
 
If you see the service call indication shown above, turn off the power switch, and then turn it back on and try 
to print again.
If the error is not cleared after turning the power switch off and then back on, press Go, the LEDs will light up 
as shown in the table below to identify the error.
1If this...

Control Panel 
59
3
Note
Make sure that the front cover is completely closed before you report a service call.
 
 

Control Panel 
60
3
Go button3
The Go button has the following functions:
Cancel printing
Cancel the current job being printed: While printing press Go for about 4 seconds until all the LEDs light 
up and then release it. The Ready and Error LEDs will flash as the job is being canceled.
Cancel all the received jobs: To delete all jobs, press Go for about 4 seconds until all the LEDs light up 
and then release it. Press Go again. The Ready and Error LEDs will flash as the job(s) is being canceled....

Control Panel 
61
3
Print a test page3
You can use Go or the printer driver to print a test page.
Using the Go button3
aTurn off the machine.
bMake sure that the front cover is closed and the power cord is plugged in.
cHold down Go as you turn on the power switch. Keep Go pressed down until the Toner, Drum and Error 
LEDs light up. Release Go. Make sure that the Toner, Drum and Error LEDs are off.
dPress Go again. The machine will print a test page.
Using the printer driver3
If you are using the Windows®...

Control Panel 
62
3
Print a Printer Settings page3
You can print the current settings using the control panel button or printer driver.
Using the Go button3
aMake sure that the front cover is closed and the power cord is plugged in.
bTurn on the machine and wait until the machine is in Ready mode.
cPress Go three times within 2 seconds. The machine will print the current printer settings page.
Using the printer driver3
If you are using the Windows® printer driver, you can print the current printer...

Control Panel 
63
3
Print Fonts (HL-2250DN / HL-2270DW only)3
You can print a list of the internal fonts using the control panel button or printer driver.
Using the Go button3
aTurn off the machine.
bMake sure that the front cover is closed and the power cord is plugged in.
cHold down Go as you turn on the power switch. Keep Go pressed down until the Toner, Drum and Error 
LEDs light up. Release Go. Make sure that the Toner, Drum and Error LEDs are off.
dPress Go twice. The machine will print a list of...

Control Panel 
64
3
Print a WLAN report (HL-2135W / HL-2270DW only)3
You can use Go to print machines wireless status report. See chapter 5 of the Network Users Guide.
Default settings3
The machine has three levels of default settings; the default settings have been set at the factory before 
shipment.
Network default settings
Factory reset
Settings reset
Note
• You can not modify the preset default settings.
• Page counter can never be changed.
 
Network default settings (HL-2135W / HL-2250DN /...

Control Panel 
65
3
Settings Reset3
This operation will reset all the machine settings back to the settings that were set at the factory:
aTurn off the machine.
bMake sure that the front cover is closed and the power cord is plugged in.
cHold down Go as you turn on the power switch. Keep Go pressed down until all the LEDs light up and 
the Ready LED turns off.
dRelease Go. Make sure that all the LEDs turn off.
ePress Go ten times. The machine will automatically restart.
 

66
4
4
You will need to clean the machine regularly and replace the consumable items.
Replacing consumable items4
The machine will indicate when it is time to replace the consumable items. (See LEDs (Light Emitting Diodes) 
on page 53)
Consumables4
Routine Maintenance4
Toner cartridgeDrum unit
See Toner cartridge on page 70
Model Name: TN-2010, TN-2210, TN-2220See Drum unit on page 77.
Model Name: DR-2200