Brother HL 2130R User Manual

							Routine Maintenance 
77
4
Drum unit4
A new drum unit can print approximately 12,000 A4 or Letter size single-sided pages at 1 page / job.
Note
• There are many factors that determine the actual drum life, such as the temperature, humidity, type of 
paper, type of toner used, number of pages per print job and so on. Under ideal conditions, the average 
drum life is estimated at approximately 12,000 pages. The actual number of pages that your drum will print 
may be significantly less than this estimate. Because we have no control over the many factors that 
determine the actual drum life, we cannot guarantee a minimum number of pages that will be printed by 
your drum.
• For best performance, use only genuine Brother toner. The machine should be used only in a clean, dust-
free environment with adequate ventilation.
• Printing with a non-Brother drum unit may reduce not only the print quality but also the quality and life of 
the machine itself. Warranty coverage does not apply to problems caused by the use of a non-Brother 
drum unit.
 
DRUM END SOON4
If the Drum LED flashes, it means the drum unit will need to be replaced soon. We recommend that you 
replace the drum unit with a new one before there is a noticeable deterioration in the print quality.
 
 
						

							Routine Maintenance 
78
4
REPLACE DRUM4
If the Drum LED is on, it means the drum unit should be replaced. Please replace it with a new Brother drum 
unit.
 
DRUM STOP4
If the Drum and Error LEDs are on, it means the drum unit must be replaced. Replace it with a new Brother 
drum unit.
 
 
						

							Routine Maintenance 
79
4
Replacing the drum unit4
Before you replace the drum unit, see Before replacing the consumable items on page 67.
When you replace the drum unit with a new one, you need to reset the drum counter by completing the 
following steps:
aMake sure that the machine is turned on and the Drum LED is flashing. Leave the machine for at least 
10 minutes to cool down.
bOpen the front cover. 
cTake out the drum unit and toner cartridge assembly. 
 
						

							Routine Maintenance 
80
4
IMPORTANT
• We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper 
or cloth in case you accidentally spill or scatter toner.
• To prevent damage to the machine from static electricity, DO NOT touch the electrodes shown in the 
illustration.
 
 
dPush down the green lock lever and take the toner cartridge out of the drum unit. 
eUnpack the new drum unit.
 
						

							Routine Maintenance 
81
4
fPut the toner cartridge firmly into the new drum unit until you hear it lock into place. If you put the cartridge 
in properly, the green lock lever will lift automatically.
 
gPut the drum unit and toner cartridge assembly back into the machine. Do not close the front cover yet. 
 
						

							Routine Maintenance 
82
4
hPress and hold down  Go for about 4 seconds until all the LEDs light up. Once all four LEDs are lit, 
release Go.
 
IMPORTANT
Do not reset the drum counter when you only replace the toner cartridge.
 
iClose the front cover.
jMake sure that the Drum LED is now off.
 
						

							Routine Maintenance 
83
4
Cleaning4
Clean the outside and inside of the machine regularly with a dry, lint-free cloth. When you replace the toner 
cartridge or the drum unit, make sure that you clean the inside of the machine. If printed pages are stained 
with toner, clean the inside of the machine with a dry, lint-free cloth.
WARNING 
DO NOT use flammable substances, any type of spray or any organic solvent/liquid that contains alcohol 
or ammonia to clean the inside or outside of the machine. Doing this may cause a fire or electrical shock.
 
 
 
Be careful not to inhale toner.
 
IMPORTANT
Use neutral detergents. Cleaning with volatile liquids such as thinner or benzine will damage the surface 
of the machine.
 
 
						

							Routine Maintenance 
84
4
Cleaning the outside of the machine4
aTurn off the machines power switch. Disconnect all cables, and then unplug the power cord from the AC 
power outlet.
bPull the paper tray completely out of the machine.
cWipe the outside of the machine with a dry, lint-free cloth to remove dust. 
dRemove all the paper, and anything that is stuck inside, from the paper tray.
eWipe the inside of the paper tray with a dry, lint-free cloth to remove dust. 
fPut the paper back in the paper tray.
gPut the paper tray back in the machine.
hPlug the machines power cord back into the AC power outlet first, and then reconnect all cables. Turn 
on the machines power switch.
 
						

							Routine Maintenance 
85
4
Cleaning the corona wire4
If you have print quality problems, clean the corona wire as follows:
aOpen the front cover and leave the machine for at least 10 minutes to cool down.  
bTake out the drum unit and toner cartridge assembly. 
IMPORTANT
• We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper 
or cloth in case you accidentally spill or scatter toner.
• To prevent damage to the machine from static electricity, DO NOT touch the electrodes shown in the 
illustration.
 
 
 
						

							Routine Maintenance 
86
4
cClean the primary corona wire inside the drum unit by gently sliding the green tab from right to left and 
left to right several times. 
 
Note
Be sure to return the tab to the home position (a) (1). If you do not, printed pages may have a vertical stripe.
 
dPut the drum unit and toner cartridge assembly back into the machine. Close the front cover. 
1