Home > Brother > Sewing Machine > Brother Correctoball Xl1 Manual

Brother Correctoball Xl1 Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Brother Correctoball Xl1 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 331 Brother manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							
    49
    4
    ■Bobbin tension is too tight
    Loops appear on the wrong side of the fabric.
    Solution
    Increase the tension by 
    turning the upper tension-
    control dial to a higher 
    number.
    Note
    ●If the loops still appear on the wrong side of 
    the fabric after you adjust the upper tension, 
    the bobbin thread may be too tight. In this 
    case, turn the screw counterclockwise being 
    careful not to over-loosen the screw, 
    approximately 30-45 degrees to decrease 
    bobbin tension. After you adjust the bobbin 
    thread, adjust the upper thread to match the 
    bobbin thread.
    a Screw
    1
    2 3 45
    aWrong side
    b Surface
    c Upper thread
    d Lower thread
    e Loops appear on 
    wrong side of 
    fabric
    LS2125_Appendix.fm  Page 49  Thursday, February 28, 2008  11:09 AM 
    						
    							APPENDIX ——————————————————————————————————————————————————————————
    50
    TROUBLESHOOTING
    If the machine stops operating correctly, check the following possible problems before requesting service.
    You can solve most problems by yourself. If you need additional help, the Brother Solutions Center offers the 
    latest FAQs and troubleshooting tips. Visit us at [http://solutions.brother.com].
    If the problem persists, contact your dealer or the nearest authorized service center.
    SymptomPossible causeHow to put it rightReference
    The sewing 
    machine does 
    not work.The machine is not plugged in. Plug the machine in. page 10
    The main power switch is turned off. Turn on the main power switch. page 10
    The bobbin winder shaft is pushed to 
    the right.Move the bobbin winder shaft to the 
    left.page 13
    You have not used the foot control-
    ler properly.Use the foot controller properly. page 11
    The needle 
    breaks.You have not inserted the needle 
    properly.Insert the needle properly. page 20
    The needle clamp screw is loose.Use the screwdriver to firmly tighten 
    the screw.page 21
    The needle is bent or blunt. Replace the needle. page 20
    You have not used the right combi-
    nation of fabric, thread and needle.Choose a thread and needle that are 
    appropriate for the type of fabric. page 19
    The presser foot you are using is not 
    appropriate for the type of stitch that 
    you want to sew.Attach the presser foot that is correct 
    for the type of stitch that you want to 
    sew.page 35, 36, 
    38, 40, 41
    The upper thread tension is too tight. Loosen the upper thread tension. page 28
    You are pulling the fabric too much. Lightly guide the fabric. –
    The area around the hole in the nee-
    dle plate is scratched.Replace the needle plate.
    Contact your retailer or the nearest 
    authorized service center.–
    The area around the hole in the 
    presser foot is scratched.Replace the presser foot.
    Contact your retailer or the nearest 
    authorized service center.–
    The bobbin case is scratched.Replace the bobbin case.
    Contact your retailer or the nearest 
    authorized service center.–
    You have not used a bobbin that has 
    been designed for this machine.Incorrect bobbins will not work 
    properly. Only use a bobbin that has 
    been designed for this machine.page 12
    The upper 
    thread breaks.You have not threaded the upper 
    thread properly. (for example, you 
    have not fitted the spool properly, or 
    the thread has come out of the guide 
    above the needle.)Correct the upper threading. page 16
    There are knots or tangles in the 
    thread.Remove any knots or tangles. –
    The needle is not appropriate for the 
    thread you are using.Choose a needle that is appropriate 
    for the type of stitch. page 19
    The upper thread tension is too tight. Loosen the upper thread tension. page 28
    The thread is tangled, for example, 
    in the shuttle race.Remove the tangle thread. If the 
    thread is tangled in the shuttle race, 
    clean the shuttle race.page 46
    LS2125_Appendix.fm  Page 50  Tuesday, February 26, 2008  2:59 PM 
    						
    							
    51
    4
    The upper 
    thread breaks.The needle is bent or blunt. Replace the needle. page 20
    You have not inserted the needle 
    properly.
    Insert the needle properly. page 20
    The area around the hole in the nee-
    dle plate is scratched. Replace the needle plate.
    Contact your retailer or the nearest 
    authorised service center.
    –
    The area around the hole in the 
    presser foot is scratched. Replace the presser foot.
    Contact your retailer or the nearest 
    authorised service center.
    –
    The bobbin case is scratched, or has 
    a burr on it. Replace the bobbin case.
    Contact your retailer or the nearest 
    authorised service center.
    –
    You have not used a bobbin that has 
    been designed for this machine. Incorrect bobbins will not work
    properly. Only use a bobbin that has 
    been designed for this machine.
    page 12
    The lower 
    thread is tangled 
    or breaks. You have not wound the bobbin 
    thread properly.
    Wind the bobbin thread properly. page 12
    The bobbin is scratched or does not 
    turn smoothly. Replace the bobbin. –
    The thread is tangled. Remove the tangled thread and 
    clean the shuttle race.
    page 46
    You have not used a bobbin that has 
    been designed for this machine. Incorrect bobbins will not work 
    properly. Only use a bobbin that has 
    been designed for this machine.
    page 12
    Bobbin is set incorrectly. Reset the bobbin thread correctly. page 14
    The thread is 
    tangled on the 
    wrong side of 
    the fabric. The upper thread was not threaded 
    correctly.
    Correct the upper threading. page 16
    The thread ten-
    sion is incorrect. You have not threaded the upper 
    thread properly.
    Correct the upper threading. page 16
    You have not wound the bobbin 
    thread properly. Wind the bobbin thread properly. page 12
    You have not used the right 
    combination of fabric, thread and 
    needle. Choose a thread and needle that are 
    appropriate for the type of fabric. 
    page 19
    You have not attached the presser-
    foot holder properly. Attach the presser-foot holder prop-
    erly.
    page 24
    The thread tension is incorrect. Adjust the tension of the upper 
    thread.
    page 28
    You have not used a bobbin that has 
    been designed for this machine. Incorrect bobbins will not work
    properly. Only use a bobbin that has 
    been designed for this machine.
    page 12
    Bobbin is set incorrectly. Reset the bobbin thread correctly. page 14
    The upper 
    thread is too 
    tight. The bobbin thread is incorrectly 
    installed.
    Correctly install the bobbin thread. page 14
    SymptomPossible causeHow to put it rightReference
    LS2125_Appendix.fm  Page 51  Friday, February 29, 2008  10:20 AM 
    						
    							APPENDIX ——————————————————————————————————————————————————————————
    52
    The fabric is 
    wrinkled.You have not threaded the upper 
    thread properly or fitted the bobbin 
    properly.Thread the upper thread and wind 
    the bobbin thread properly.page 14, 16
    You have not fitted the spool prop-
    erly.Fit the spool properly. –
    You have not used the right 
    combination of fabric, thread and 
    needle.Choose a thread and needle that are 
    appropriate for the type of fabric.page 19
    The needle is bent or blunt. Replace the needle. page 20
    If you are sewing thin fabric, the 
    stitch is too thick.Sew with stabiliser material under 
    the fabric.page 31
    The thread tension is incorrect.Adjust the tension of the upper 
    thread.page 28
    Stitches are 
    skipped.You have not threaded the upper 
    thread properly.Correct the upper threading. page 16
    You have not used the right combi-
    nation of fabric, thread and needle.Choose a thread and needle that are 
    appropriate for the type of fabric.page 19
    The needle is bent or blunt. Replace the needle.
    page 20
    You have not inserted the needle 
    properly.Insert the needle properly.
    Dust has accumulated under the 
    needle plate or in the shuttle race.Remove the needle plate cover and 
    clean the plate and the shuttle race.page 46, 47
    There is a high-
    pitched noise 
    while sewing.Dust has built up in the feed dogs or 
    in the shuttle race.Clean the shuttle race. page 46
    You have not threaded the upper 
    thread properly.Correct the upper threading. page 16
    The bobbin case is scratched.Replace the bobbin case.
    Contact your retailer or the nearest 
    authorized service center.–
    You have not used bobbin that has 
    been designed for this machine.Incorrect bobbins will not work 
    properly. Only use a bobbin that has 
    been designed for this machine. page 12
    Insufficient oiling.Make sure to oil the machine once a 
    week if you use it more than an hour 
    a day. If you use it more often, oil 
    every day.page 45
    The stitch is not 
    sewn correctly.The presser foot that you are using is 
    not correct for the type of stitch.Attach the presser foot that is correct 
    for the type of stitch that you want to 
    sew.page 33, 36, 
    38, 40, 41
    The thread tension is incorrect.Adjust the tension of the upper 
    thread.page 28
    The thread is tangled, for example, 
    in the shuttle race.Remove the tangle thread. If the 
    thread is tangled in the shuttle race, 
    clean the shuttle race.page 46
    The fabric does 
    not feed.You have not used the right combi-
    nation of fabric, thread and needle.Choose a thread and needle that are 
    appropriate for the type of fabric.page 19
    The thread is tangled, for example, 
    in the shuttle race.Remove the tangle thread. If the 
    thread is tangled in the shuttle race, 
    clean the shuttle race.page 46
    The sewing light 
    bulb does not 
    come on.The sewing lamp is damaged. Change the sewing light bulb. page 45
    SymptomPossible causeHow to put it rightReference
    LS2125_Appendix.fm  Page 52  Tuesday, February 26, 2008  2:59 PM 
    						
    							53
    INDEX
    A
    accessories ..................................................................... 9
    appliqués ...................................................................... 41
    B
    basic stitching ............................................................... 33
    blind hem stitching ....................................................... 33
    bobbin .......................................................................... 14
    bobbin case .................................................................. 14
    bobbin winder .............................................................. 12
    button sewing ............................................................... 38
    buttonhole foot ............................................................. 36
    buttonhole sewing ........................................................ 36
    C
    cleaning ........................................................................ 46
    D
    darning ......................................................................... 35
    E
    embroidering ................................................................ 41
    extra spool pin .............................................................. 22
    F
    feed dogs ................................................................. 8,47
    flat bed attachment .................................................. 8,31
    foot controller ............................................................... 27
    free-arm style ................................................................ 31
    G
    gathering ...................................................................... 43
    H
    handwheel ...................................................................... 7
    J
    joining .......................................................................... 44
    M
    main parts ....................................................................... 6
    main power switch ....................................................... 10
    monogramming ............................................................ 41
    N
    needle .......................................................................... 19
    needle bar thread guide .................................................. 8
    needle clamp screw ................................................. 8
    ,21
    needle plate ............................................................. 8,47
    O
    oiling ............................................................................ 45
    overcasting stitches ....................................................... 32
    P
    pattern selection dial ............................................... 6,26
    presser foot .............................................................. 8
    ,23
    presser foot holder ................................................... 8,24
    presser foot lever ..................................................... 7,16
    pre-tension disk ............................................................ 12
    R
    relative chart of sewing fabrics, needles and threads ..... 19
    repacking ...................................................................... 48
    reverse sewing lever ..................................................... 28
    S
    satin stitching ................................................................ 32
    seam ripper ................................................................... 37
    sewing machine needles ............................................... 19
    shell tuck stitching ........................................................ 43
    shuttle hook removal .................................................... 47
    shuttle race cleaning ..................................................... 47
    spool pin ............................................................... 12
    ,16
    straight stitch ................................................................ 33
    stretch blind stitch ........................................................ 33
    stretch fabrics ............................................................... 31
    T
    thick fabrics .................................................................. 30
    thin fabrics .................................................................... 31
    thread cutter ................................................................. 28
    thread guide ................................................................. 16
    thread tension ............................................................... 28
    trial sewing ................................................................... 30
    troubleshooting ............................................................. 50
    twin needle ............................................................ 21
    ,22
    U
    upper tension-control dial ............................... 28,29,48
    upper threading ............................................................ 16
    W
    winding the bobbin ...................................................... 12
    Z
    zigzag stitches ................................................ 30,32,41
    zipper foot .................................................................... 40
    zipper insertion ............................................................. 40
    LS2125.book  Page 53  Tuesday, February 26, 2008  1:43 PM 
    						
    							LS-2125_brother_cover_Eng
    K
    English
    XE4592-001
    Printed in China
    Operation ManualBasic Sewing and Mending Machine
    APPENDIX UTILITY STITCHES SEWING BASICS KNOWING YOUR 
    SEWING MACHINE
    Please visit us at 
    http://solutions.brother.com
     where you can get product support and answers to frequently 
    asked questions (FAQs). 
    						
    All Brother manuals Comments (0)

    Related Manuals for Brother Correctoball Xl1 Manual