Boxlight Xd-15c Users Guide

Operation
17 BOXLIGHT XD-15c User’s Guide
3. Source Menu  
Mirror
1. Default
2. Ceiling - 
mounted 
projection
3. Rear screen 
projection
4. Ceiling - 
mounted and 
rear screen 
projection 
SourceSelects sources between PC, Video, S-Video, and YPbPr.
VolumeAdjusts the volume level.
TrebleAdjusts the treble level. 
BassAdjusts the bass level.
Mute
1.   2.
3.4.
OffOn 

Operation
18 BOXLIGHT XD-15c User’s Guide
4. Control Menu
5. PIP Menu
These functions are valid only when the input mode is PC and the PIP source is Video or 
S-Video.  LanguageLanguage sets the OSD to display in one of 7 languages.
Use 3 / 4 key to select the languages: English, French, Ger-
man, Italian, Spanish, Simplified Chinese and Traditional Chi-
nese. 
OSDSelects a desired OSD position.
OSD TimeSets the length of time the OSD will remain active after the last 
time you pressed the  button. The...

Operation
19 BOXLIGHT XD-15c User’s Guide
Shutdown
1. Press POWER and a warning message will prompt up. To turn off the projector, 
Press POWER again.
2. The fan will continue to run for approximately 60 seconds.
3. Disconnect the power cord from the wall socket.
Caution
Please do not unplug the power cord before POWER is shut down or dur-
ing the 60-second cooling process. 
If the projector is not properly shut down, to protect the lamp, the system 
will detect this and cool the lamp for two minutes...

Maintenance
20 BOXLIGHT XD-15c User’s Guide
MAINTENANCE
Lamp Information 
Use and Replacement of Lamp
When the Lamp Indicator lights up red or a message appears suggesting the time of lamp 
replacement, please install a new lamp or consult your dealer. An old lamp could cause a 
malfunction in the projector and in rare instances may even explode.
LED Status Indicators    
Caution
The LAMP indicator will light up if the lamp becomes too hot. Turn off the 
power and let the projector cool for 45 minutes....

Maintenance
21 BOXLIGHT XD-15c User’s Guide
  
1. Press the POWER button to switch off the projector.  Disconnect the power 
cord from the outlet and the projector.
2. Loosen the screw and remove the lamp cover. If the lamp is hot, avoid burns by 
waiting 45 minutes until the lamp has cooled.
3. Loosen the 3 screws. (It is strongly recommended you use a magnetic-headed 
screwdriver.) Pull the handle to remove the lamp housing. If the screws are not 
loosened completely, they could injure your fingers. Do...

Maintenance
22 BOXLIGHT XD-15c User’s Guide
Caution
To reduce the risk of severe burns, allow the projector to cool for at least 45 
minutes before replacing the lamp.
To reduce the risk of injuries to fingers and damage to internal components, 
use caution when removing lamp glass that has shattered into sharp pieces.
Please call BOXLIGHT Technial Support if your lamp has exploded. 
To reduce the risk of injuries to fingers and/or decreasing image quality by 
touching the lens, do not touch the empty...

Maintenance
23 BOXLIGHT XD-15c User’s Guide
Service Information
Accessories (Included in the Standard Package)
Optional Accessories (Not Included in the Standard Package)    
Ordering Parts or Getting Information
For product information, product assistance, service information, or to order 
accessories, please contact BOXLIGHT Corporation at 1-800-762-5757 or +1-360-
779-7901 or visit the web site at www.boxlight.com
. Power cord (EU)
Power cord (US)
Power cord (UK)
VGA signal cable
Video cable
S-Video...

Troubleshooting
24 BOXLIGHT XD-15c User’s Guide
TROUBLESHOOTING
Common Problems & Solutions
PROBLEMS TRY THESE SOLUTIONS
NO POWER Plug the power cord into the AC inlet.
 Plug the power cord into the power inlet.
 Wait two minutes after the projector is turned off before turning 
the projector back on.
NO PICTURE Check for the proper input source.
 Ensure all cables are connected properly.
 Adjust the brightness and contrast. 
 Remove the lens cap.
TRAPEZOID 
IMAGE ON 
THE SCREEN Reposition the...

Troubleshooting
25 BOXLIGHT XD-15c User’s Guide
 Status Messages      
On Screen Messages  Description
SEARCHINGProjector is searching for input.
INPUT SIGNAL 
DETECTED, 
ACTIVATING AUTO 
IMAGEProjector has identified the input signal and is running the auto 
image adjustment function.
SYNC IS OUT OF 
RANGEInput signal frequency exceeds the projector’s range.
CHANGE THE LAMP, 
AND RESET THE LAMP 
TIMER The lamp has been in operation for 1400 hours. Lamp replace-
ment is recommended.
CHANGE THE LAMP, 
THE...

Specifications
26 BOXLIGHT XD-15c User’s Guide
SPECIFICATIONS
Projector Specifications 
Technical Specifications
Note: All specifications are subject to change without notice.
                              
                       General
Product name Personal Projector
Model name BOXLIGHT XD-15c         
1024X768  XGA
Optical
Display system 1-CHIP DMD
Lens F/Number F/2.6
Lamp 120W VIP lamp
Electrical
Power supply AC100 ~ 240V, 2.3A, 50/60 Hz (Automatic)
Power consumption 185 W (Max)
Mechanical
Dimensions...