Boxlight Xd 10m Manual

13
Using the Remote Control
To use the forward and back buttons on the remote to advance 
slides in PowerPoint, you must connect the USB mouse connector 
on the computer cable to the computer. See page 7 for details. 
Point the remote control at the projection screen or at the front of 
the projector (not at the computer). The range for optimum oper-
ation is about 25 feet/7.6m. If you point the remote at the projec-
tion screen, the distance to the screen and back to the projector 
must be less than or...

14
Using the Projector
Using the Keypad and Remote Buttons
While the menus are displayed, the 
source and reset buttons on 
the keypad and the up and down arrow buttons on the remote 
act as menu navigation and adjustment buttons and the 
menu/select button acts as a select button. See “Using the On-
Screen Menus” on page 16 for details.
FIGURE 11
Keypad and remote buttons
Menu/select 
NOTE: If you have turned Auto
Source off (page 22), you may
need to press the source button
more than once to display...

15
Reset (keypad only)
Resets the options in the menus (except Language, Video Stan-
dard, and Rear Projection) to their original settings.
Keystone + - (remote only) 
Use this feature to adjust the image vertically and make a more 
square image.
1Press the 
keystone + button to reduce the upper part of the 
image, and press the 
key sto ne  - button to reduce the lower 
part. You can also adjust keystone from the Display menu (see 
page 17 for details on the menu).
FIGURE 12
Adjusting the keystone...

16
Using the Projector
Using the On-Screen Menus
The projector
 has menus that allow you to make image adjust-
ments and change a variety of settings. These adjustments aren’t 
available directly from the keypad. 
NOTE: Some menu items may be
grayed out (dimmed) at certain
times. This indicates the item is
not applicable to your setup or the
item is not enabled until another
selection is made.
To open the on-screen menus, press the menu/select button on the 
keypad or remote. (The menus automatically...

17
Display Menu
To access the Display menu settings, press the 
menu/select button 
to display the Main menu, press the down arrow to highlight Dis-
play, then press 
menu/select again to access the Display menu.
 
FIGURE 14
Display menu
Ke y s t o n e
This option helps to keep the image square as the angle of projec-
tion is changed. Use this feature to adjust the image vertically 
and make a squarer image. See page 15 for details on keystone 
adjustments.
1Press the down button to highlight Keystone,...

18
Using the Projector
Contrast
The contrast controls the degree of difference between the lightest 
and darkest parts of the picture. Adjusting the contrast changes 
the amount of black and white in the image.
1Use the up and down arrows to highlight Contrast, press 
menu/select, use the arrows to adjust the contrast, then press 
menu/select to accept your changes.
Tint
NOTE: The color setting applies
to video sources only. The tint
setting applies to NTSC video
sources only.
The tint adjusts the...

19
Image Menu for Computer Sources
To access the Image menu settings, press the 
menu/select button 
to display the Main menu, press the down arrow to highlight 
Image, then press 
menu/select again to access the Image menu.
FIGURE 15
Image menu for computer sources
Resize
Resize 
allows you to select from among four different re-sizing 
options. The default is 
Standard, which resizes the image from its 
original version to fit a standard 4x3 aspect ratio screen. 
Wide-
screen Letterbox
 preserves the...

20
Using the Projector
Manual Sync 
The projector adjusts signal synchronization automatically for 
most computers. But if the projected computer image looks fuzzy 
or streaked, try turning 
Auto image off then back on again. If the 
image still looks bad, try adjusting the signal synchronization 
manually:
1Tu r n  A u t o  I m a g e  o f f .
2Highlight Manual sync, press 
menu/select, use the arrow but-
tons to adjust Manual sync until the image is sharp and free of 
streaks, then press 
menu/select....

21
Image Menu for Video Sources
FIGURE 16
Image menu for video sources
Resize
Resize 
allows you to select from among four different re-sizing 
options. The default is 
Standard, which resizes the image from its 
original version to fit a standard 4x3 aspect ratio screen. 
Wide-
screen Letterbox
 preserves the 16x9 aspect ratio of the original 
theater version, but the image is placed in a 4x3 space, so black 
bars appear at the top and bottom of the image. 
Enhanced Wide-
screen
 also preserves the...

22
Using the Projector
Control Menu
To access the Control menu settings, press the 
menu/select button 
to display the Main menu, press the down arrow to highlight 
Control, then press 
menu/select again to access the Control menu.
FIGURE 17
Control menu
Auto Source 
When this feature is On, the projector automatically finds the 
active source, checking the default source first. When this feature 
is Off, the projector defaults to the source selected in Default 
Source. To display another source, you...