Boxlight Raven Users Manual

							xUser’s Manual
* This table is for user reference only.
wPosition the projector in a horizontal position; other positions can cause heat build-up 
and damage to the projector.
wMake sure the heat ventilation holes are not blocked. Do not use the projector in a 
smoky environment. Smoke residue maycause buildup on critical parts (i.e. DMD, 
lens assembly, etc.). 
						

							xUser’s Manual
Using the Projector
Control Panel
LED
1. POWER (Power LED indicator)
Refer to ”Indicator Messages”.
2. LAMP (Lamp LED indicator)
Refer to “Indicator Messages”.
Button Function
1.
Refer to “Powering On/Off the Projector”.
2.  MENU  ENTER
Press the MENU\ENTER button to activate the OSD (On-Screen Display) menu. Use the directional buttons and 
MENU\ENTER button to navigate through the OSD (On-Screen Display) menu and select choices.
3. KEYSTONE (
u/v)
Adjusts image distortion caused by tilting the projector.
4. AUTO (
t)
Automatically adjusts frequency and phase.
5. Four direction buttons
The four direction buttons
stuvcan be used to scroll through OSD (On-Screen Display) menus and 
make adjustments.
6. SOURCE (
s)
Manually selects an input source. 
						

							xUser’s Manual
Remote Control
1. Power
Refer to “Powering On/Off the Projector”.
2.  Four direction buttons
The four direction buttons 
stuvcan be used to scroll
through OSD (On-Screen Display) menus and make 
adjustments.
3. Menu
Press the Menu button to activate the OSD (On-Screen 
Display) menu. Use the directional buttons and Menu 
button to navigate through the OSD (On-Screen 
Display) menu.
4. Enter
Confirms the selection
5. Keystone  
uv
Adjusts image distortion caused by tilting the projector.
6. Volume 
uv
Press the Volume ubutton to increase the volume press 
the Volume 
vbutton to reduce the volume.
7. Source 
Manually selects an input source.
8. Mute
Cuts off the sound temporarily.
9. Blank
Cuts off the screen temporarily.
10. 4:3/16:9
Press the 4:3/16:9 to switch the image aspect ratio from 
4:3 to 16:9.
11. Auto
Automatically adjusts frequency and phase. 
						

							xUser’s Manual
Battery Replacement
1. Push and slide the battery compartment lid in the direction shown.
2. Install a battery as indicated by the diagram inside the compartment.
3. Position the lid over the compartment and snap it back into place.
wKeep the battery out of the reach of children. There is a danger of 
death by accidentally swallowing the battery.
wDo not recharge the used battery or expose the battery to fire or water.
wDo not dispose of the used battery along with household waste. 
Dispose of used batteries according to local regulations.
wAvoid excessive heat and humidity. Danger of explosion may happen if
a battery is incorrectly replaced. Replace only with the same type
recommended by the manufacturer. 
						

							xUser’s Manual
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
A. Straight Distance:Within about 7 meters 
from the front of the 
remote sensor.
B. Direction:
Angle: Within about 20 degrees
of the remote sensor in
every direction.
Distance:within about 3 meters
from the front of the
remote sensor.
wThe remote control may not operate when there is sunlight or other
strong light such as a fluorescent lamp shining on the remote sensor.
wOperate the remote control from a position where the remote sensor 
is visible.
wDo not drop the remote control or jolt it.
wKeep the remote control out of locations with excessively high
temperature or humidity.
wDo not get water on the remote control or place wet objects on it.
wDo not disassemble the remote control.
203m20
7m
2020
7m
3m
3m
3m 
						

							xUser’s Manual
Menu Options
The projector has multi-language OSD (On-Screen Display) menus that can only be displayed when an input
source is present. The menus can be accessed using either the Projector Control Panel or the Remote Control.
The OSD (On-Screen Display) menus allow you to make image adjustments and change a variety of settings. 
If source is a computer, the OSD (On-Screen Display) allows changes to the Display tab. When using a video
source, the OSD (On-Screen Display) allows changes to the Video tab. The projector automatically detects 
the source.
1.Press the MENU\ENTERbutton on the Projector Control Panel or the Menu button on the 
Remote Control.
2.Select the menu tab with the stbuttons either on the Projector Control Panel or the Remote Control.
3.Select the desired menu option item with the uvbuttons either on the Projector Control Panel or the 
Remote Control.
xTo enter its respective sub-menu, refer to each menu option section for more details.
4.To exit from the menu:
xOn the Projector Control Panel: Go back to main menu tab with the uvbuttons, and press the 
MENU\ENTER button.
xOn the Remote Control: press the MENUbutton.
wThe illustrations in this manual are for the purpose of explanation and
may differ from the actual setting of your projector. 
						

							xUser’s Manual
IMAGE
Option Actions/Descriptions
Contrast  Controls the degree of difference between the lightes and darkest 
parts of the picture. Adjusting the contrast changes the amount of 
black and white in the image.
Select the desired setting with the 
stbuttons:
xPress the sbutton to decrease the contrast.
xPress thetbutton to increase the contrast.
Brightness  Adjusts the brightness of the image. 
Select the desired setting with the 
st buttons:
xPress the sbutton to lighten the image.
xPress the tbutton to darken the image.
Keystone  Adjusts image distortion caused by tilting the projector.
Select the desired setting with the 
stbuttons:
xPress the sbutton to reduce the upper width.
xPress the tbutton to reduce the lower width.
Aspect Ratio  Selects this function to fit 1:1, 16:9, 4:3 aspect ratio. In order to use the
1:1 aspect ratio, the input must be a computer signal (through VGA 
cable) of resolution less than SVGA (800 x 600). If the input signal is a 
computer signal greater than SVGA or component 1080i / 720p, only 
16:9 or 4:3 aspect ratio will be available. 
						

							xUser’s Manual
Select the desired setting with the stbuttons:
x1:1: The input source will be displayed without scaling
x16:9: The input source will be displayed in wide screen mode (16:9) 
without scaling. The source will be scaled to fit the width of the screen.
x4:3: The input source will be scaled to fit the screen.
Blank Screen  Blanks the screen temporarily, and selects the screen color when 
Blank Screen is active.
Select the desired setting with the stbuttons:
xWhite
xBlack
xBlue
xGray
xRed
xGreen
xYellow
xCyan
xMagenta
Gamma Selects Gamma Mode.
Select the desired setting with the stbuttons:
xFilm : Dark video image mode
xPhotographic: Computer photo mode
xRGB: Computer text mode
xVideo : Common video mode
White Peaking  White Peaking can be adjusted between 0 and 10.
Select the desired setting with the stbuttons:
xSetting 10 will maximize the brightness.
xSetting 0 will maximize color reproduction quality. 
						

							xUser’s Manual
Color Temperature Adjusts the color temperature. With the higher temperature, the 
screen looks colder; with the lower temperature, the screen looks 
warmer. Red, Green and Blue mode activate only if the Color 
Temperature is set to ”User”.
Select the desired setting with the stbuttons:
xHi
xMid
xLow
xUser
Red  Manually adjusts red.
Select the desired setting with the stbuttons:
xPress the sbutton to decrease the color temperature.
xPress the tbutton to increase the color temperature.
Green  Manually adjusts green.
Select the desired setting with the stbuttons:
xPress the sbutton to decrease the color temperature.
xPress the tbutton to increase the color temperature.
Blue  Manually adjusts blue.
Select the desired setting with the stbuttons:
xPress the sbutton to decrease the color temperature.
xPress the tbutton to increase the color temperature. 
						

							xUser’s Manual
Video
Option Actions/Descriptions
Saturation  Adjusts a video image from black and white to fully saturated color.
Select the desired setting with the s tbuttons:
xPress the tbutton to decrease the amount of color in the image.
xPress the sbutton to increase the amount of color in the image.
Tint  Adjusts the color balance of red and green.
Select the desired setting with thes tbuttons:
xPress thetbutton to increase the amount of green in the image.
xPress thesbutton to increase the amount of red in the image.
Sharpness  Adjusts the sharpness of the image.
Select the desired setting with thes tbuttons:
xPress thetbutton to decrease the sharpness.
xPress thesbutton to increase the sharpness.