Boxlight Projector Write 5 User Manual

							69  MENU  
 
Security   Menu   
   
  
Step: 
  1. Use the ▲ /▼buttons to  
select  an item. 
  2. Use the ◄ /  ► buttons  
to  select  an item or adjust 
the value.  
 
 
 
 
  Item   Selection  
Description  
 
 
 
 
 
PIN LOCK 
PROTECTION    
 
 
 
OFF 
ON 1  
ON 2   OFF:   T urn   o f f PIN lock   protection.  
ON 1:   After   plugging   in   AC powe r , you need   to   key   in   PIN 
code at the first   time of use. If the   AC power stays 
plugged,   you do not   need   to   key   in   PIN code   next 
time   when you use the   projecto r .  
ON 2:   Y ou need   to   key   in   PIN code   every   time   when you 
turn   on the   projecto r .  
    CAUTION:  
Once   the   PIN code   had   been   set,   the   projector   cannot   be 
used unless you enter   the   correct   PIN code.    
 
 
 
 
 
 
 
 
 
 
MODIFY   PIN    
 
 
 
 
 
 
 
 
 
EXECUTE    
1. Press “   MENU ”   on the   projector   or remote   control.  
2. Use the  ►   button to select the MODIFY   PIN item of the  
SECURITY   categor y .  
3.  Pres s   th e   ►   butto n   t o   chang e   PI N   LOC K   PROTECTION  
mode.  
4.  E nter   the   original   PIN code.  
(a)   If the   PIN is   correct,   system   will   allow   you to   change 
a   new PIN code.  
(b)  I f  
the  PI N  is incorrect, a “ Code Error ” message will  appea r .  
5.  Pleas e   ente r   a   ne w   PI N   code ,   a n d   the n   ente r   agai n   t o   confirm.  
NOTE:  
(1)   T o   change   the   PIN lock   protection   state,   you must  
enter the PIN code first.  
(2) Please enter: 0000 for first - time   use.  
(3)   T o   avoi d   unnecessar y   trouble ,   i f   yo u   activat e   th e   [PIN 
Loc k   Protection] ,   i t   i s   highl y   recommende d   tha t   you 
writ e   dow n   th e   PI N   cod e   an d   stor e   i t   i n   a   saf e   place.   
						

							70  MENU  
 
Security   Menu  
Step:  
1.Use the  ▲   / ▼ buttons to  
select   an   item.  
2.Use the  ◄   /  ►   buttons to  
select   an   item   or adjust   the 
value.   
   
  
 
 
 
Item   Selection  Description  
FI L TER   TIMER  
  Show the filter   use hou r .  
RESET   FI L TER 
TIMER    
EXECUTE    
Reset the filter   timer after cleaning / changing filte r .  
 
FI L TER   COUNTER   500 hours  
800 hours  
1000 hours    
Select   (500 / 800 / 1000 hours) depending   on the 
environment.(default   : 500 hours).  Please   see   as belo w .  
 
 
MAC   ADDR.     If purchasing   LAN control   module,   MAC   ADDR. will   be 
shown in   Security   Menu.  
MAC address stands for unique   Media   Access Control 
address of LAN control   module   and   displays   with   six 
groups of two hexadecimal   digits.  
 
 
 
 
CL OS E D   C AP T ION   OFF(Default) 
C.C1  
C.C2  
C.C3  
C.C4  
T1  
T2  
T3  
T4    
The   Closed   Caption   function   intimates   the   sound e f fects, 
dialogue,   and   narration   in   the   content   of the   television 
program   or video   source.  
Caption   (C.C1~C.C4) : Display   closed   caption   T ext 
(T1~T4)   : Display   text   data,   which   is   for additional 
information   such as news reports   or a   TV   program   guide. 
NOTE :   This   function   is   available   only   in   video   / S - V ideo  
source.  
 
LAN MODULE    
OFF 
ON   If purchasing   LAN control   module,   LAN MODULE will 
be   shown in   Security   Menu.  
Select   ON/OFF to   turn   on/o f f   LAN control   feature.  
 
LAN SETTING    
EXECUTE   Enter   LAN SETTING to   set   up projector   network  
configuration.   
						

							71  MENU  
 
Security   Menu  
Step:  
1.Use the  ▲   / ▼ buttons to  
select   an   item.  
2.Use the  ◄   /  ►   buttons to  
select   an   item   or adjust   the 
value.   
   
  
 
 
 
Item   Selection  Description  
PROJEC T OR 
NAME   Default   is  
Projector   Projector   network   setting   display   which   shows bits   that   can 
be   recognized   by   ASCII.  
 
DHCP    
OFF / ON   When   setting   ON, projectors   IP   address will   be   assigned   by 
DHCP   server   automaticall y .   When   setting   OF F , you can   use 
remote   control   to   do setting   manuall y .  
 
IP     Key in   IP   address manuall y .   Press ENTER to   do digit 
setting.   When   it   appears,   press 
▲   / ▼   to adjust value.  
When finishing   value adjustment, press MENU to exit.  
 
 
MASK    
Enter   MASK address manuall y .   Press ENTER to   do digit 
setting.   When   it  appears,   press 
▲   / ▼   to adjust value.  
When finishing   value adjustment, press MENU to exit.  
 
G A TE W A Y     Enter   G A TE W A Y   address manuall y .   Press ENTER to   do 
digit   setting.   When   it  appears,   press 
▲   / ▼   to adjust value. 
When finishing   value adjustment, press MENU to exit.   
						

							72  MENU   
   
  
Auto Filter Alert  
Auto Filter Alert is in SECURITY category to show the air filter use time and alert user 
to change filter. Pressing  ► cursor button will display a dialog. When the operating time 
reaches the set time, a warning message will appear on the screen to remind user of filter 
cleaning / replacing.  
 
 
 
 
Filter Replace... 
  Filter has been used for more than 500 hours.  
 
 
 
 
 
 
 
►NOTE  
Please reset the Filter time only when you replace the filter.   
						

							73  MENU   
   
  
   
   
   
  
PIN Key In Operation 
 
When  the projector is turned on  and the 
PI N LOCK PROTECTION is  set to [ON], 
th e image will show as on  the right side.  
 
1. Press  the MENU button on  the projector 
or remote control. Enter  PIN code by 
keypad or remote control.  
 
2. How to enter a  PIN code?  
You  can us e control panel or remote 
control.  
  CONTROL PANEL  REMOTE CONTROL  The control panel and remote
 control buttons 
to enter a sequence 
of PIN code  is like the photo below.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
(1) Press  ◄ button: Select the [ 1 ] 
(2) Press  ▲ button: Select the [ 2 ] 
(3) Press  ► button: Select the [ 3 ]  
(4) Press  ▼ button: Select the [ Enter ] move to next row.(4~6,7~9, 
  ~OK)
 
(5) Press    (backspace) item:
 
In case you enter a wrong digit, select   
to  delete the wrong digit you entered.  
(6) Press    item:
 
Once all four digits of the PIN are entered, select    to confirm.
 
 
► NOTE  
 
If the PIN is incorrect, an  “Enter  new code”  message will  be shown. Please try again. If the PIN 
code
 input  is incorrect for three times, a warning message will show up and the  projector will shut 
itself down in 30 seconds.  
If you have no idea about the PIN, please contact your dealer for help.   
						

							74  Network Cont r ol   Softwa r e   Application   
   
  
LAN 
 
 
 
 
 
 
 
 
 
 
Procedure  to utilize this function  
 
It can  help user to monitor and manage the projector(s) status  in the local area network.  
  Register the projector(s) which needs 
to be  controlled.  
 Auto search  can help you to seek the projector(s) source easily.  
After registering  in the work group, you can start  to control the projector.  
  Group the projector(s) into 
different sections.  
You can monitor the status easily by the sort of group name function  in the network.
 
  Monitor the status for each projector.
 
a. Y ou can  manage and change the monitoring content by System Parameter Setting.  
b. The Lamp timer, filter working time or system warning feedback etc. can be found  
by checking the status of  projector(s). 
  Control the booked projector(s).
 
The status can be refreshed and acquired by monitoring functions; you can also  
operate the function easily by Network Control.  
 
►NOTE  
 
To  mo nito r  and  co ntro l  the  p r ojecto r   ( includ in g  stand-b y  mo d e) ,  the  fo llo win g 
conditions need  to be  ready:  
(1) Projector should already  be powered on. 
(2) Projector  is connected  to network.  
(3)  LED  light  of  the  projector  network  port  shows  normal.  (Green  light  on,  Orange 
twinkle)  
* Stand- by mode indictor: Green LED (Power)  on the projector ‟s control panel flashes.  
 
 
Before Using Network Control Software  
1.  The projector should  be powered on and the LAN wire  is well connected  to projector.  
 
2. The LAN module ON/OFF item  in SECURITY menu of OSD should  be setting  ON. 
 
3. Make sure the computer and projector  can connect  to network. Network Control software needs to 
arrange  in TCP/IP network communication and the network cable.  
► NOTE:  
 
IE8 browser & 1024x768 viewing resolution  is recommended.   
						

							75  Network Cont r ol   Softwa r e   Application   
   
Browser Control  
Auto IP address setting (while DHCP setting  is ON):  
(1) Enable DHCP from the projector  on-screen-display menu, under SECURITY \ LAN SETTING. 
(2) Please wait for the PC server  to release  IP address to the projector.  
(3)  Enter  Given  IP address  (For  example  http://192.168.1.176/) into  the  address  bar of  the  web  browser  and 
press “Enter”  key or click “Go” button.  
 
 
   
 
 
   
 
Item Setting description:  
  ITEM   SETTING   DESCRIPTION  
Home   (Status)   Show current projector status and network configuration  settings.  
Control   Panel   Select   projecto r ‟ s   detailed   setting   from   this   page.  
Network   Set up network 
configuration  and password from this page.  
Alert   Setting   Show and setup   Alert configurations.  
Schedule   Show and set up Schedule, including   W eekly Schedule and Specific   Da y .  
T ime   Set   up the   date/time   on the   projecto r .  
Creston   Creston configuration.  
Logout   Logout   information.  
If the Administrative & User password is enabled, select your User Name and enter password to login.
  
						

							76  Network Cont r ol   Softwa r e   Application   
   
  
 
 
 
 
 ADMINISTRATOR    MODE 
User n a m e :  admin 
Password: (Default password setting is disabled.) 
 
 
 
 
 
 
Home (Status):  
Show current projector status and network 
configuration settings.  
 
    
						

							77  Network Cont r ol   Softwa r e   Application   
   
 ITEM   ITEM  SETTING  DESCRIPTION  
Status   Projector   Name   Show   projector   name.  
  System   Status   Show   if   projector   is   Power   On   or   Inactive .  
  Input  
Source   Show   current   input  source.  
  Lamp   Hours   Show   lamp   hours used   on   current   projecto r .  
  Filter   Hours   Show   filter hours used  on   current   projecto r .  
W ired  
LAN   IP  Address   Show   current   IP   address   of   wired  LAN.  
  Subnet   Mask   Show   current   Subnet   Mask   of   wired   LAN.  
 
Gateway   Show   current   Gateway   of   wired  LAN.  
  MAC  
Address   Show   current   MAC   Address   of   wired  LAN.  
W ireless   LAN   Mode   Access   Point   Mode.  
 
SSID  
SSID   (Service   Set   Identification)  is   the   wireless   network  name,  
it   must   be   assigned   to   wireless   devices   in   your  network.  
  Channel  
Thi s   fiel d  determine s   whic h   operatin g   frequenc y   wil l   b e   used. 
Th e   defaul t   channe l   i s   se t   t o   Auto ,   s o   th e   A P   wil l   choos e  
the 
best   channel  automatically.  
  IP  
Address   Show   current   IP   address   of   W ireless  LAN.  
  Subnet   Mask   Show   current   Subnet   Mask   of   W ireless   LAN.  
 
Gateway   Show   current   Gateway   of   W ireless  LAN.  
 
MAC  Address   Show   current  MAC  Address   of   W ireless   LAN.  
Download 
T ool   W indows   T o   dow nl oa d   th e   appl ica ti o n   progr a m   o f   E Z   W i Fi_ LA N.  
The   file   is   W indows   OS   only   for   EZ   Display  used.  
  MAC   T o   dow nl oa d   th e   appl ica ti o n   progr a m   o f   E Z   W i Fi_ LA N.  
The   file   is   MAC   OS   only   for   EZ   Display   used.  
 
Contr ol Panel:  
Select projector ‟s detailed setting from this page.
    
						

							78  Network Cont r ol   Softwa r e   Application   
   
  ITEM   SETTING   DESCRIPTION  
Basic  
Projector   Name   Show   projector   name   on   the   current   projecto r .  
Power   Power   On   or   Power   O f f   the   projector   via   network.  
Input   Source   Select   input   source.  
Pictu r e  
Brightness   Adjust   the   image   brightness   level.  
Contrast   Adjust   the   image   contrast   level.  
Sharpness   Adjust   the   image   sharpness.  
Color   Adjust   the   strength   of   whole   colo r .  
This   function   can   only   be   used   under   V ideo   signal,   S - V ideo   signal,   or   component 
video   signal   input.  
T int   Adjust   the   image   tint.  
This   function   can   be   used   under   V ideo   signal,   S - V ideo   signal,   or   component   video 
signal.  
Display   Mode   Adjust  Natural/Cinema/Daylight/Green  Board/White   Board/Black/User   Mode.  
Audio  
V olume   Adjust   the   volume.  
Mute   Mute   the   volume   OFF   / ON.  
Setting  
Keystone   Manually   correct   vertical   keystone   distortion   in   image.  
Auto   Sync   Set   all   of the   above   setting   automaticall y .   (This   function   can   only   be   used   under   PC  
mode)  
Auto   Search   Search   signal   source   manually   or   automaticall y .  
Advanced  
Blank   Blank   the   current   image   on   the   screen  
Blank   Power   O f f   No   / 15   / 30   / 60   (minutes)  
Freeze   Freeze   the   current   image   on   the   screen.  
Resize   4:3,16:9,   1:1,   16:10  
Reset   All   Reset   all   menu   function   to   their   factory   default   values.  
P r esentation  
Projection   Select  
Front/Ceiling/Rear/Celing  and   Rear  
Lamp   Mode   Switch   lamp   mode   between   Powerful   or   Normal   mode.