Bose Lifestyle 50 Owners Guide

							        AM189854_05_V.PDF October 17, 2001 29
6 DISK MAGAZINE
6 6
5 5
4 4
3 3
2 2
1 1
6 6
5 5
4 4
3 3
2 2
1 1
6 DISK MAGAZINE6 6
5 5
4 4
3 3
2 2
1 1
6
 D
I
S
K
 
M
A
G
A
Z
IN
E6 6
5 5
4 4
3 3
2 2
1 1Eject button
Operating Your Lifestyle® 50 System
Listening to compact discs
Using the CD changer
You can load the CD changer with up to six compact discs at a time.
Loading discs into the CD magazine
To load the CD magazine, hold it as shown in Figure 31. Insert up to six discs, label side
up. Take care to place only one disc in each slot. Note the slot numbers 1 through 6, from
bottom to top, on the front edge window. These numbers correspond to the CD numbers
on the display.
CAUTION: Do not insert more than one disc into any slot. Forcing two discs into one slot
could cause them to become stuck, and could damage the discs, the CD magazine, or the
CD changer.
Note: If a disc is upside-down, it does not play. The display flashes the disc number.
Figure 31
Loading and ejecting a CD
Ejecting discs from the CD magazine
Press the white lever that corresponds to the disc you want to eject. This ejects the disc far
enough for you to grasp the edge and remove it from the magazine (Figure 31).
Loading the CD magazine into the CD changer
Open the CD changer door. Insert the CD magazine fully into the CD changer, following the
direction of the arrow on the magazine (Figure 32).
Ejecting the CD magazine from the CD changer
Press the EJECT button, at the lower left of the magazine slot, to remove the magazine
(Figure 32). If a CD is playing, pressing the EJECT button stops the CD, replaces it in the
magazine, and ejects the magazine.
Figure 32
Loading and unloading the CD
magazine
 
						

							30 October 17, 2001                  AM189854_05_V.PDF
Operating Your Lifestyle® 50 System
Turning the system on and choosing the CD changer
Press the CD source button to select the CD changer. If the system is off, this turns it on at
the same time. When you press CD, the CD changer display (Figure 33) appears on the
display. If a CD has been loaded, it begins to play. If no disc is installed, a noCd message is
displayed.
Note: To prevent excessive wear on the CD mechanism, CD play or random play operations
automatically stop after 24 hours.
Figure 33
The CD changer display
To play a CD
Press the PLAY  button. The button symbol  flashes until play begins.
To pause a CD
Press the PAUSE   button. The button symbol    flashes. Press PAUSE or PLAY to resume.
If left unattended, the CD changer mode changes from PAUSE to STOP after 20 minutes. You
can skip tracks forward or backward while paused.
To stop a CD
Press the STOP  or OFF button. If you press STOP , the disc number, total play time and
number of tracks appear briefly on the display.
To skip to other tracks
To skip to the next track, press the TRACK forward    button. To skip to the previous track,
press the TRACK backward  
  button. Pressing TRACK    while playing a CD skips you to
the beginning of the track in play.
To play another disc
Press the DISC forward  or backward  button. This skips you to the next or previous disc
in the changer and starts playing the CD. The message CHANGING is displayed until play
begins. Empty disc changer slots are automatically skipped.
ÂENU
SLEEP
ON
OFF
VOLUÂE
VOLUÂE
ÂUTE SOURCE
DISC
TRACKPLAY PAUSE STOP
PLAY
LIST
KEYPAD
OÂIT
TRACK
PLAY, PAUSE, STOP
and PLAY LIST buttonsElapsed play time
for current track
Press and hold here to store a
TRACK number in the CD play list Scan CD
backwardScan CD
forwardSkip DISC
or TRACK
forward Skip DISC or
TRACK
backwardRemoves TRACK
number from normal play
 
						

							        AM189854_05_V.PDF October 17, 2001 31
Operating Your Lifestyle® 50 System
To scan a disc
Press and hold the scan forward    or backward    button (these are the ones to the left
and right of the play time display). Scanning back or forward stops at the first or last track of
the disc. You can scan a CD while it is paused.
To add a track to the play list
Skip to the track you want to add to the play list. Press and hold the TRACK number display
area. The current track number is stored in the next available location in the CD play list.
To omit a track from normal play
Select the TRACK number, then press and hold the OMIT TRACK button. You can omit up to
15 tracks and you can omit a track while it is playing. Omitted tracks are not played during
normal, repeat, or random play modes.
You can skip to an omitted track using the TRACK forward  
  or backward    button.
When on an omitted track, the word OMITTED is displayed and the OMIT TRACK button
becomes CLEAR OMIT TRACK.
To clear an omitted track and restore it to normal play, skip to the omitted track number and
then press CLEAR OMIT TRACK. To clear all omitted tracks at the same time, eject the CD
magazine.
To listen to the CD play list
•Press the PLAY LIST button (Figure 34).
•To cancel PLAY LIST, press STOP, or press PLAY LIST again. If you press STOP, the
current CD stops playing. If you press PLAY LIST again, the current CD continues to play.
Note: The PLAY LIST button appears only after you store CD selections in the play list
memory. To program a play list, see “Programming a CD play list” on page 33.
If the play list has an invalid entry, such as a track number that can’t be found, it is skipped
during play. If a CD was removed or exchanged, the system tries to play the disc as pro-
grammed. Unavailable items are skipped.
Figure 34
Display after pressing
PLAY LIST
ÂENU
SLEEP
ON
OFF
VOLUÂE
VOLUÂE
ÂUTE SOURCE
LIST
DISC
TRACKPLAY PAUSE STOP
PLAY
LIST
 
						

							32 October 17, 2001                  AM189854_05_V.PDF
Operating Your Lifestyle® 50 System
Using the CD OPTIONS menu
From the CD OPTIONS menu you can select repeat or random play, or program a CD play
list. To access the CD OPTIONS, press the MENU button until CD OPTIONS is displayed
(Figure 35). You can do this while a CD plays if you wish.
Figure 35
CD options display
Selecting repeat and random modes
Repeat and random modes remain active until you press STOP  or OFF. To place the
system in a repeat or random mode, go to the MENU button and select CD OPTIONS. Use
the REPEAT and RANDOM buttons to select the mode you want. Press DONE to exit the CD
OPTIONS menu. To cancel a repeat or random mode, press OFF in the CD OPTIONS menu.
You can select the following repeat and random modes:
Mode Press What it does
Repeat trackREPEAT TRACK Repeats selected track for 24 hrs.
Repeat CDREPEAT DISC Plays all tracks on selected disc in order.
Repeats for 24 hrs.
Repeat allREPEAT ALL Plays all loaded discs in order. Repeats for
24 hrs.
Random CDRANDOM DISC Plays selected disc once in random order
and stops.
Random allRANDOM ALL Plays all tracks on all discs once in
random order and stops.
Repeat random CDREPEAT DISC then RANDOM DISC Plays selected disc in random order.
Repeats for 24 hrs.
Repeat random allREPEAT ALL then RANDOM ALL Plays all discs and tracks in random order.
Repeats for 24 hrs.
Selecting play list modes
You can also apply repeat or random modes to your CD play list. Press the PLAY LIST button
before pressing the MENU button to select the CD OPTIONS menu. Then select one of the
following play list modes using the REPEAT and RANDOM buttons. When you are through,
press DONE to exit.
Play list mode Press What it does
Random listRANDOM DISC or RANDOM ALL Plays all selections in the PLAY LIST
once in random order.
Repeat listREPEAT DISC or REPEAT ALL Repeats PLAY LIST.
Repeat track listREPEAT TRACK Repeats selected PLAY LIST item.
Repeat random listREPEAT DISC or REPEAT ALL Plays and repeats all selections in the
then RANDOM DISC or RANDOM ALL PLAY LIST in random order.
Note: If you select random and repeat modes that cannot be combined (REPEAT TRACK
and RANDOM DISC, for example), the system accepts the most recently entered choice.
ÂENU
SLEEP
ON
OFF
VOLUÂE
VOLUÂE
ÂUTE
CD OPTIONSDISC
TRACK PLAY
LIST
EDITDISC REPEAT
RANDOÂALLALL
OFF DISC TRACK
DONE
Press to program
a CD play listPress for random
or repeat modes
 
						

							        AM189854_05_V.PDF October 17, 2001 33
Operating Your Lifestyle® 50 System
ÂENU
SLEEP
ON
OFF
VOLUÂE
VOLUÂE
ÂUTE ITEÂ 
DISC
TRACK
DONE
STORE
CD OPTIONS
Press to store selected DISC and TRACK
Programming a CD play list
Using the Lifestyle® system’s programming feature, you can create your own CD play list of
up to 50 tracks (including repeats) from the loaded discs. You can create or edit a CD play list
even while listening to another source. However, you can’t edit the play list while the list is
playing. To create or edit a CD play list, press the MENU button and select CD OPTIONS.
Note: If you have more than one Personal™ music center, only one user can edit the play list
at a time.
To create a CD play list
1. Press EDIT PLAY LIST. The next available item number is flashing to indicate that the
music center is ready for programming (Figure 36).
2. Select a DISC and TRACK number using the 
 or  arrow buttons.
3. Press STORE to enter the CD selection into memory under the selected ITEM number. The
ITEM number stops flashing.
4. Press the ITEM right 
 arrow for the next item number.
5. Repeat steps 2, 3 and 4 to add more items to the list. When the list has 50 programmed
items, the STORE button disappears.
6. When you have completed your play list, press DONE to exit.
Figure 36
Starting to build the CD play list
To change an entry in the CD play list
1. Press EDIT PLAY LIST. If the list has 50 items stored, the ITEM field indicates FULL and
does not flash.
2. Select the number of the item you want to change and press CLEAR.
3. Select a new DISC and TRACK and press STORE.
4. To make other changes, repeat steps 2 and 3. Otherwise, press DONE to exit.
Next available location flashes
 
						

							34 October 17, 2001                  AM189854_05_V.PDF
Operating Your Lifestyle® 50 System
ÂENU
SLEEP
ON
OFF
VOLUÂE
VOLUÂE
ÂUTE
CD OPTIONS
ITEÂ 
DISC
TRACK
CLEAR
LISTDONE
CLEARINSERT
Press to insert
item into list Press to remove
item from listPress to remove
entire list
To insert a new track in an existing play list
1. Press EDIT PLAY LIST. If the ITEM field indicates FULL, you can’t insert a new item unless
you delete one or more items from the list.
2. Select the ITEM number of the location where you want to insert a new CD selection. The
ITEM number should not be flashing.
3. Press INSERT (Figure 37). The ITEM number begins flashing to indicate that the item
you were viewing was moved up one item number leaving your selected ITEM number
available.
4. Select a DISC and TRACK number and press STORE.
To delete a track from the play list
1. Press EDIT PLAY LIST.
2. Select the number of the item you want to delete and press CLEAR (Figure 37). The
TRACK and DISC numbers change to dashes. The location is cleared and all items after
this one are moved down one item number.
3. To delete other items, repeat step 2. Otherwise, press DONE to exit.
Figure 37
CLEAR LIST and CLEAR
buttons available on the display
after first selection is entered
To erase the entire CD play list
1. From the CD OPTIONS menu, press CLEAR LIST.
2. Press YES to confirm.
 
						

							        AM189854_05_V.PDF October 17, 2001 35
Using the system with external components
Follow the instructions on pages 12-15 for connecting components.
Turn on your component directly or by using its remote control. Press VOLUME 
 or  on
your Personal™ music center to raise or lower the volume. Control all other functions at the
source, referring to its owner’s manual if necessary. To begin, make sure the component is
turned on and a tape, CD, DVD, laserdisc, etc. is loaded. If an external component sounds
significantly louder or softer than other sources, see “Equalizing the volume levels of external
sources” on page 37.
Note: The Lifestyle® 50 system cannot turn a connected component on or off.
Turning the system on and selecting the component
Press VIDEO 1, VIDEO 2, AUX, or TAPE on your Personal music center to select the desired
component. This turns your system on and selects the component connected to that input. If
the system is already on, this button selects the component.
The appropriate display indicator appears when the system is on and the component is
selected.
CAUTION: The magnetic field from the Acoustimass® module is not an immediate risk to
your video tapes, audio tapes, and other magnetic media. However, you should not store
tapes directly on or near the Acoustimass module.
Using a tape recorder with your system
If you are listening to any source except TAPE, the output signal of that source is directed to
the RECORD OUT jacks.
Note: The ROOM outputs of the Lifestyle® 50 system are designated by the letters A through
D. In a multi-room system, the source that is playing in the room designated by the letter
closest to the begining of the alphabet is sent to the RECORD OUT jacks.
You may also specify a source to be directed to the RECORD OUT jacks even if you are not
listening to that source. To do this:
1. Select RECORD OUT with the MENU button. The words RECORD OUT are displayed
under the source display area (Figure 38).
2. Select a source to record. The selected source appears in the source display area in place
of the dashes (Figure 38). If you want to remove your RECORD OUT selection, press
CLEAR. The dashes reappear.
The selected source stays on until you turn RECORD OUT off. If the CD changer is
selected for RECORD OUT, it shuts off after 24 hours if you have not turned it off sooner.
3. When you are ready, set the tape deck to record.
Figure 38
The RECORD OUT menu
display
Operating Your Lifestyle® 50 System
 
						

							36 October 17, 2001                  AM189854_05_V.PDF
®
Treble
Bass
Operating Your Lifestyle® 50 System
Fine-tuning your system
In most situations, you only need to follow the speaker placement guidelines (see “Setting
Up” on pages 6-8) for your system to provide excellent sound quality. You do not need to
adjust tone settings for changes in volume, since Bose
® patented integrated signal process-
ing provides a natural tonal balance over the full range of volume settings.
If desired, you can further fine-tune your system as described here.
Adjusting speaker controls
The Lifestyle® 50 system treble and bass controls are located on the Acoustimass® module
(Figure 39). They allow you to adjust the treble (high frequencies) and bass (low frequencies).
In the normal setting, the dots on each control are in the 12 o’clock position. You can also
locate the normal setting by feeling when the control settles into the notch at this position.
Turn the controls clockwise to increase, and counterclockwise to decrease, the amount of
treble or bass.
Compensating for room acoustics
The acoustics (sound qualities) of your room can affect the overall sound quality of any
speaker system. In general, you can reduce many problems with acoustics by the careful use
of the treble and bass controls.
Too much or too little treble
Rooms that reflect a lot of sound, especially those with bare floors and walls, may sound
overly shrill or “bright.” Turning down the treble control (toward – ) decreases treble sound.
Rooms with a lot of sound-absorbing furnishings, such as upholstered furniture, wall-to-wall
carpet, or heavy drapes, may sound muffled or dull. Moving speakers further away from soft
furnishings increases treble. You can increase treble sound by slightly turning up the treble
control (toward + ).
Too much or too little bass
You can decrease bass sound by turning down the bass control (toward – ). To increase bass,
turn up the bass control (toward + ). Acoustimass module placement also affects the amount
of bass you hear. Placing the module closer to the corner of the room increases bass. Moving
the module away from the corner decreases bass.
Optimizing AM/FM radio reception
You can adjust the orientation of your AM/FM antenna for the strongest signal by selecting
SIGNAL LEVELS with the MENU button (Figure 40). Select the AM or FM radio, and the
display shows you the strength level of the received signal. While watching the display,
reposition your antenna until the highest possible signal level is achieved. The signal level can
vary from 0 to 99. The manual tuning keys are provided so that you can check the signal
strengths of multiple stations.
Figure 40
AM/FM antenna signal strength
display
Figure 39
Treble and bass controls
 
						

							        AM189854_05_V.PDF October 17, 2001 37
Operating Your Lifestyle® 50 System
Equalizing the volume levels of external sources
The SIGNAL LEVELS selection in the MENU options allows you to adjust and equalize the
volume gain levels received from externally connected sources (VIDEO 1, VIDEO 2, AUX, TAPE).
For example, you can adjust the gain level of an external source so that volume level 50 on this
source sounds as loud as level 50 from a built-in source.
1. Using the MENU button, select SIGNAL LEVELS.
2. Press VIDEO 1, VIDEO 2, TAPE or AUX and you are shown a gain adjustment display
(Figure 41). After listening to the built-in sources (FM, AM, CD) at your preferred volume
level, use the arrow keys to adjust the signal level settings (GAIN) of the connected
sources until you get the same volumes. The adjustment range is from –15 to +15.
Figure 41
Gain adjustment display
Adjusting LCD contrast
You can adjust the contrast of the display. Press and hold the SOURCE button until Lcd
appears. Use the lower arrow buttons to change the contrast level.
Figure 42
LCD contrast adjustment
display
Adjusting the Personal™ music center beep
You can adjust the loudness of the beep made when pressing the display buttons. Press and
hold the SOURCE button until Lcd appears. Use the upper arrow buttons to select the bEEP
display. Use the arrow buttons to select between Lo, HI, and– – (off).
Figure 43
Beep adjustment display
 
						

							38 October 17, 2001                  AM189854_05_V.PDF
Forcing the SOURCE buttons to stay on
Normally, the SOURCE buttons are automatically removed from the display following certain
operations. You can change the behavior of these buttons so that they remain in the state you
last set them (on or off screen) using the SOURCE button.
1. Press and hold the SOURCE button until Lcd appears.
2. Press either upper arrow key until you see STAY and the SOURCE button appears in the
upper left region of the display (Figure 44).
3. Press either lower arrow key to select 
 (Yes).
4. To return the SOURCE buttons to normal operation, select 
 (No).
Figure 44
Selecting the display mode of
the SOURCE buttons
Forcing the KEYPAD buttons to stay on
Normally, the numerical keypad buttons are automatically removed from the display following
certain operations. You can change the behavior of these buttons so that they remain in the
state you last set them (on or off screen) using the KEYPAD button.
1. Press and hold the SOURCE button until Lcd appears.
2. Press either upper arrow key until you see STAY and the KEYPAD button appears in the
upper right region of the display (Figure 45).
3. Press either lower arrow key to select 
 (Yes).
4. To return the KEYPAD to normal operation, select 
 (No).
Figure 45
Selecting the display mode of
the KEYPAD buttons
ÂENU
SLEEP
ON
OFF
VOLUÂE
VOLUÂE
ÂUTE SOURCE
DONE
ÂENU
SLEEP
ON
OFF
VOLUÂE
VOLUÂE
ÂUTE
DONE
KEYPAD
= KEYPAD buttons are removed following certain operations.
Press KEYPAD to access them again.
= KEYPAD buttons remain as you last set them with the
KEYPAD button.
= SOURCE buttons are removed following certain operations.
Press SOURCE to access them again.
= SOURCE buttons remain as you last set them with the
SOURCE button, except for when the system is off.
Operating Your Lifestyle® 50 System