Home > Bose > Music System > Bose Lifestyle 40 music system Sold from 1999 to 2002 User Manual

Bose Lifestyle 40 music system Sold from 1999 to 2002 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Bose Lifestyle 40 music system Sold from 1999 to 2002 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 223 Bose manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							      AM189858_03_V.pdf December 20, 2001 9
    OFF
    POWER
    ON
    RIGHT
    OUTPUTS
     TO
    CUBE
     SPEAKERS
    LEFT
    AUDIO
    INPUT
    Setting Up
    Right
    speaker
    Right-angle connector
     into AUDIO INPUTLeft
    speaker
    Audio input cable
    Power jackMulti-pin
    connector
    into
    ROOM AAC
    power
    pack Blue connectors from
    BOSE CD to BOSE CD
    Connecting the Acoustimass® module to the multi-room interface
    Connect the module to the interface with the audio input cable (Figure 7).
    1. Insert the right-angle multi-pin connector on the audio input cable into the AUDIO INPUT
    jack on the module. Align the connector at the angle shown in Figure 7.
    2. Plug the small black multi-pin connector (flat side facing up) into the jack marked ROOM A
    (PRIMARY) on the back of the interface.
    Note: Be sure that each connector is inserted completely into each jack.
    For information on connecting multi-room systems, see “Connecting additional rooms” on
    page 32.
    Connecting the CD changer to the multi-room interface
    Connect the CD changer to the interface with the CD changer cable (Figure 7).
    1. Plug a blue multi-pin connector (flat side facing up) into the jack marked BOSE CD on the
    back of the interface.
    2.Plug the other blue multi-pin connector (flat side facing left) into the jack marked BOSE
    CD on the back of the CD changer.
    Note: Be sure that each connector is inserted completely into each jack.
    Figure 7
    Speakers, CD changer, and
    multi-room interface connec-
    tions 
    						
    							10 December 20, 2001                AM189858_03_V.pdf
    Setting Up
    230 V
    115 V
    Connecting the Acoustimass® module power (mains) cord
    CAUTION: If you have a dual-voltage system, make sure the voltage selector switch on the
    Acoustimass module is set correctly.
    1. On a dual voltage system, the voltage selector switch is preset at the factory to be correct
    for your area. Check to be sure it is set for the proper voltage (Figure 8). Use 115V for
    North America; 230V for Europe and Australia. In Europe, use the adapter plug provided. If
    you are in doubt, contact your local electric utility for the appropriate voltage setting.
    Note: Do not plug the AC power cord into a power outlet until all component connections
    are complete.
    2. Plug the small end of the power (mains) cord into the Acoustimass module AC power jack.
    Figure 8
    Dual voltage Acoustimass
    module: voltage selector switch
    settings
    Connecting the multi-room interface power pack
    The multi-room interface comes with either a 100V, 120V, 230V, or 240V power pack. See
    Figures 1 and 9. Dual voltage models include both the PS71 and PS72 power packs.
    CAUTION: Be sure to use the correct Bose® power pack for your area. Using the wrong one
    may damage your power pack or your system.
    •Model PS71, 120V in North America•Model PS72, 230V in Europe
    •Model PS73, 100V in Japan•Model PS74, 230V in UK or Singapore
    •Model PS77, 240V in Australia
    Figure 9
    The AC power pack
    (model PS71 shown)
    Note: Do not plug the power pack into a power outlet until you complete all component
    connections.
    1. Firmly insert the small connector on the end of the power pack cable into the AC power
    jack on the back of the multi-room interface.
    2. Make sure that the power pack reaches an AC (mains) outlet. 
    						
    							      AM189858_03_V.pdf December 20, 2001 11
    Connecting external components
    Use standard RCA audio cables to connect other components to your Lifestyle® system’s
    multi-room interface, matching the red connector to R (right) and white (or black) connector to
    L (left).
    You can use a Y-adapter (available at electronics stores) to connect a mono source. However,
    the left and right speakers then play the same monaural sound.
    Video components
    To play video sound through your Lifestyle® music system, connect the R and L fixed audio
    outputs of your stereo VCR, stereo TV, or DVD player to the interface VIDEO 1 or 2 jacks. See
    Figure 10. You can use a Y-adapter (available at electronics stores) to connect a mono
    source. However, the left and right speakers then play the same monaural sound.
    Tape deck
    To use an external tape recorder (analog audio cassette, analog open reel, digital audio tape,
    or Digital Compact Cassette), connect the inputs (REC) of the tape deck to the interface
    RECORD OUT jacks. Connect the outputs (PLAY) from the tape deck to the interface TAPE IN
    jacks. See Figure 10.
    Laserdisc player or additional CD changer
    To use one of these components, connect its audio outputs to the interface AUX jacks,
    matching the red plug to R (right) and black or white plug to L (left). See Figure 10.
    Turntable
    To connect a turntable, you need a phono preamplifier (with RIAA equalization). You can order
    the appropriate model (PN 252603) from Bose® Customer Service (See the inside back cover
    for locations and phone numbers.). Connect the audio outputs of the phono preamplifier to
    the interface AUX jacks, matching the red plug to R (right) and black or white plug to L (left).
    Note: The Lifestyle® 40 music system cannot tur n a connected component on or off.
    Figure 10
    Connecting external
    components
    Setting Up
    ANTENNA
    FM AM
    BOSE CDAUX VIDEO 1 VIDEO 2 TAPE IN OUT
    LLLLL
    R RRRRRECORD
    ROOM A(PRIMARY)ROOM B
    ROOM D ROOM CPOWER
    SERIAL
    D ATA
    !SEE USER’S
    GUIDE
    12V     AC
    1.6A
    AUDIO INPUTAUDIO OUTPUT
    VCR, TV,
    DVD, and/or
    laserdisc VCR, TV,
    DVD, and/or
    laserdisc Other
    componentOutputs         InputsTape
    deck 
    						
    							12 December 20, 2001                AM189858_03_V.pdf
    Setting Up
    FM antenna connections
    1. Plug the FM antenna connector into the FM ANTENNA jack on the back of the interface.
    2. Spread out the antenna arms. Experiment with both the placement and the angle of this
    antenna to provide optimum FM reception.
    Note: A central antenna or cable, or an outdoor FM antenna, may be used with the multi-
    room inter face antenna connections. To install an outdoor antenna, consult a qualified
    installer. Follow all safety instr uctions.
    Figure 12
    The FM dipole antenna and
    AM loop antenna
    AM antenna connections
    Note: To install the AM antenna on a wall, follow the instr uctions enclosed with the antenna.
    1. Plug the AM antenna microplug into the AM ANTENNA jack on the interface.
    2. Stand the loop antenna on the base, following the instructions enclosed with the antenna.
    3. Move the loop part of the antenna as far away from the multi-room interface as possible,
    but at least 20 inches (50 cm) away, and at least 4 feet (1.2 m) from the Acoustimass
    ®
    module. Experiment with the orientation of the loop for optimum AM reception.
    Connecting to a cable radio signal
    To connect your system to the FM signal available from some cable TV companies, contact
    your cable provider for assistance. The connection is made to the FM 75Ω EXTERNAL
    antenna connector on the back of the interface.
    CAUTION: Be certain that the installation includes a signal splitter so that only the FM band,
    not the cable TV band, is transmitted to the system. It is necessar y to use a splitter that filters
    the signal to prevent any re-emissions of the TV spectr um through the system.
    AM antenna
    jack Coaxial (75Ω)
    FM antenna jack
    Connecting the antennas
    The rear panel of your multi-room interface provides connections for the supplied AM and FM
    antennas (Figure 11). Untie and straighten the bundled wires on each antenna. Antennas
    provide better reception when their wires are fully extended.
    Figure 11
    The antenna connections 
    						
    							      AM189858_03_V.pdf December 20, 2001 13
    Setting Up
    Completing connections and turning on the Acoustimass® module
    1. Plug the Acoustimass® module power cord into an AC power (mains) outlet.
    2. Plug the multi-room interface power pack into an AC power (mains) outlet.
    3. When you have checked all connections, be sure to turn the Acoustimass module power
    switch on (Figure 13). It is not necessary to turn the module off after each use. The system
    turns on and off automatically as it receives a signal from the Personal™ music center.
    Turn the system off using the Personal music center.
    Note: Your speakers will not operate unless you complete all cable and power connections
    before turning on the system.
    CAUTION: Be sure the three shipping screws on the bottom of the CD changer have been
    removed before turning on the system.
    Setting up the Personal music center
    Set up the Personal music center after the rest of the system is connected, plugged in, and
    the Acoustimass module has been turned on.
    Note: When batteries are first installed in the Personal music center, it sets up a radio-
    frequency link with the closest multi-r oom inter face.
    1. Hold the Personal music center within a few feet of the multi-room interface.
    2. Slide open the battery compartment on the back of the Personal music center (Figure 14).
    3. Insert 4 AAA or IEC-R03 1.5V batteries, or the equivalent, as shown. Match the + and –
    symbols on the batteries with the + and – markings inside the compartment.
    4. Slide the battery compartment cover back into place.
    5. Turn the Personal music center over and touch the screen to wake it up if it appears blank.
    Press ON/OFF, FM, or any other source button to turn the system on.
    If the Personal music center continuously displays “NO RESPONSE,” you need to try to
    establish its link with the multi-room interface again. Hold the Personal music center close to
    the multi-room interface. Press and hold MUTE for about 5 seconds until you hear a beep
    and then release. After about 10 seconds, the music center should beep twice to confirm that
    the link is established.
    Figure 14
    Installing batteries and waking
    up the display for the first time
    OFF
    POWER
    ON
    RIGHT
    OUTPUTS
     TO
    CUBE
     SPEAKERS
    LEFTAUDIO
    INPUT
    Figure 13
    Turning on the Acoustimass
    module
    Battery compartment cover
    4 AAA
    batteries
    b. Turn over and wake up display a. Install batteries
    Note: Replace the batteries when the LOW BATTERY message first appears. See “Replac-
    ing batteries” on page 36. Alkaline batteries are recommended. 
    						
    							14 December 20, 2001                AM189858_03_V.pdf
    Operating Your Lifestyle® 40 Music System
    Turning on the system
    You are ready to enjoy your new Lifestyle® system. Your Personal™ music center places
    complete control of the system operations in your hands. The center is portable, communi-
    cating with the rest of the system through a two-way radio-frequency link. The display is
    backlit for easy viewing, and provides visual feedback of current system operations and the
    available options. To allow for maximum battery life, the display and backlight turn off a short
    time after your last button press. You only need to touch the screen to wake up the music
    center.
    •To learn more about the display, see “Using the Personal music center display” on pages
    16-17.
    •To operate the AM/FM radio, see “Listening to the radio” on pages 18-20.
    •To operate the CD changer, see “Listening to compact discs” on pages 21-26.
    •To control external components, see “Using the system with external components”
    on pages 26-27.
    •To use your system in multiple rooms, see “Operating in more than one room” on
    pages 33-35.
    Turning the system on
    1. Touch the music center screen to wake up the display (Figure 15). The last display that you
    used appears on the screen.
    2. Press ON/OFF to turn the system on to the last source used, or press a SOURCE button
    (FM, AM, CD, VIDEO 1, VIDEO 2, TAPE, AUX) to select and turn on that source (Figure 16).
    Figure 15
    Waking up the display
    Figure 16
    Turning on a source
    Turning the system off
    •Press the ON/OFF button. 
    						
    							English
          AM189858_03_V.pdf December 20, 2001 15
    Operating Your Lifestyle® 40 Music System
    Adjusting the volume
    •Touch the VOLUME  (up) or  (down) button to raise or lower the volume.
    •Volume settings range from 0 to 100. Volume settings are displayed while being adjusted.
    •If the volume was above 80 when the system was turned off, it will turn on at 80 (to
    prevent surprising you with an extremely high volume).
    Muting your system
    •Press the MUTE button to silence the system. MUTE flashes on the display when the
    system is muted.
    •Press MUTE again or VOLUME  to restore volume to the muted speakers.
    Using the sleep timer
    1. Press the SLEEP button to access the sleep timer for automatic shutoff. The display
    flashes a sleep time of 30 minutes or the most recent sleep time setting (Figure 17). The
    SLEEP indicator is also flashing.
    2. Use the arrow buttons to set the sleep timer to 1 to 99 minutes.
    3. Press the START button to start the counter. The START button disappears and a CLEAR
    button appears at the bottom of the display.
    Figure 17
    The SLEEP display
    ÂENU
    SLEEP
    ON
    OFF
    VOLUÂE
    VOLUÂE
    ÂUTE SLEEP
    DONE
    CLEAR
    While the sleep timer is running, you can:
    •Press CLEAR to cancel the timer.
    •Press DONE to exit from the SLEEP display.
    •Press SLEEP again to view the time remaining.
    The selected SLEEP time is remembered by the music center. The next time SLEEP is
    selected, the display shows the last SLEEP time used.
    The SLEEP indicator flashes
    The CLEAR button is shown and the START button disappears
    Set time with arrow buttons
    Press START to begin countdown Before pressing START …
    After pressing START … 
    						
    							16 December 20, 2001                AM189858_03_V.pdf
    Using the SOURCE buttons
    The seven source buttons provide direct access to the three built-in sources (FM, AM, CD)
    and up to four external components connected to the system. The Lifestyle® system can
    select an external component and adjust the volume, but it cannot turn a connected compo-
    nent on or off.
    Use the SOURCE button to show or hide the source buttons.
    Using the KEYPAD buttons
    The numeric buttons provide direct access to commonly used features of the three built-in
    sources (FM, AM, CD). The 
     or  arrow symbol to the left or right of the KEYPAD button
    indicates whether you are using the keypad for presets or tuning (in FM or AM mode), or
    selecting disc or track (in CD mode).
    Use the KEYPAD button to show or hide the keypad buttons and select PRESET or TUNE, or
    DISC or TRACK.
    Using the current status display
    The center of the touchscreen displays information about the current status of the system.
    The top of the status area indicates which source is selected or if the power is off. The next
    three lines let you set tuner or CD functions, using the 
     or  arrow buttons to adjust the
    settings. The center area also includes indication of CD modes such as RANDOM and
    REPEAT, or if the SLEEP function is on.
    Operating Your Lifestyle® 40 Music System
    Primary
    buttons
    SOURCE
    buttonsCurrent status
    displayKEYPAD
    buttons Primary
    buttonsSource display
    area
    Using the Personal™ music center display
    The Personal music center display provides information on the system functions. The display
    offers different combinations of buttons to provide control of the function you are using.
    Sometimes an item on the display will flash to provide information about a system function.
    When an item flashes faster, it is alerting you to a needed action.
    Using the primary buttons
    The primary buttons (ON/OFF, SLEEP, MENU, VOLUME, and MUTE) are located at the left
    and right sides of the display.
    Figure 18
    The display showing the primar y
    buttons, SOURCE buttons, and
    KEYPAD buttons 
    						
    							English
          AM189858_03_V.pdf December 20, 2001 17
    Using the MENU items
    The menu items are selected by pressing the MENU button to step through the list until the
    function you want is displayed. Menu items are available in the list if they are applicable to the
    current state of the system. You can exit from any menu item by pressing DONE or ON/OFF
    or pressing MENU until you return to the main screen.
    Figure 19
    Selecting MENU items – one at
    a time
    PRESETS
    You can preset a maximum of 25 FM and 25 AM radio stations. In addition to using the
    PRESETS menu, you can set presets directly from the KEYPAD buttons. See pages 19-20.
    WIPE SCREEN
    Select this option when you need to wipe the display to clean off fingerprints, etc. WIPE
    SCREEN allows you 20 seconds to clean the display without affecting the system operations.
    See “Cleaning the Personal™ music center” on page 37.
    CD OPTIONS
    Select this option to create and edit a CD play list even if you are listening to another source.
    If you are in CD mode, you can also select random and repeat play. See “Using the CD
    OPTIONS menu” on pages 24-26.
    Note: The next space in the MENU list is reserved for a feature of home theater systems.
    RECORD OUT
    Use this option to select which source is directed to the RECORD OUT (line out) jacks,
    allowing you to listen to one source while recording another.  See “Using a tape recorder with
    your system” on page 27.
    SIGNAL LEVELS
    The SIGNAL LEVELS option allows you to read the received signal strength of AM and FM
    radio stations. It also allows you to equalize the volume levels of externally connected
    components. See “Optimizing AM/FM radio reception” on page 28, or “Equalizing the volume
    levels of external sources” on page 29.
    Operating Your Lifestyle® 40 Music System
    MENU items display area 
    						
    							18 December 20, 2001                AM189858_03_V.pdf
    Operating Your Lifestyle® 40 Music System
    Listening to the radio
    Your Lifestyle® music system has a built-in AM/FM radio. Good AM/FM radio reception
    depends on the location and orientation of the AM and FM antennas. See “FM antenna
    connections” and “AM antenna connections” on page 12 for proper antenna installation. See
    “Optimizing AM/FM radio reception” on page 28 for help with antenna adjustment.
    Turning the system on and choosing the radio
    Press FM or AM to turn your system on to the most recently selected FM or AM station. If the
    system is already on, use the FM or AM button to select either of these sources.
    Setting radio channel spacing
    On some multi-room interfaces, the AM and FM channel spacing can be set for North
    America (US: 10 kHz for AM and 200 kHz for FM) or Europe (EU: 9 kHz for AM and 50 kHz for
    FM). Select the channel spacing most appropriate for your area.
    To change between US and EU channel spacing, press and hold the SOURCE button for two
    seconds. Press either arrow button until tunr appears. Using the arrow buttons, select US or
    EU. Press DONE to exit.
    Selecting FM or AM
    Press the FM or AM SOURCE button to turn on the radio band desired. Select a station by
    tuning manually, seeking a strong station, or selecting a preset station.
    Manually tuning a radio station
    To manually tune a radio station, press the  (decrease) or  (increase) arrow button on
    either side of the frequency display to change the frequency in small steps (Figure 20). Or,
    press the KEYPAD button until the indicator arrow 
     points toward TUNE. Then use the
    number buttons to enter the frequency of the station you want to tune. The left-most digit is
    entered first and the display flashes while you enter more digits. When you have entered the
    station frequency, the system selects that station or the closest valid station.
    Figure 20
    Tuning the radio from the FM
    source display
    To tune a station, use up/down arrow keys, orpoint the KEYPAD to TUNE and enter numbers.
    Receiving FM stereo or monaural broadcasts
    When receiving sufficiently strong FM stereo broadcast signals, the radio automatically
    receives in the stereo mode; the STEREO indicator appears on the display. Weak stereo
    signals are received in the monoaural mode (the STEREO indicator is off).
    To force the tuner to receive in stereo mode only, press and hold the center of the station
    display until you hear a high-pitched beep. To receive in monaural mode only, press and hold
    until you hear a low-pitched beep. However, even though you may have forced the stereo
    mode, monaural broadcast material is still heard in monaural. Retuning the station cancels
    any forcing. 
    						
    All Bose manuals Comments (0)

    Related Manuals for Bose Lifestyle 40 music system Sold from 1999 to 2002 User Manual