Bosch WVH 28420 User Manual
Have a look at the manual Bosch WVH 28420 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 101 Bosch manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
1
Safety instructions
– The washer dryer is heavy – take care when lifting it.
– Warning: frozen hoses may tear/burst. Do not insta ll the washer dryer outdoors or in areas
where there is a risk of frost.
– The washer dryer may be damaged. Do not lift by pr ojecting components (e.g. washer dryer
door).
– In addition to the instructions mentioned here, sp ecial regulations of the relevant water and
power supply companies may apply.
– If in doubt, have the appliance connected by a tec hnician.
– Lay hoses and cables in such a way that there is no risk that they can be tripped over.
Environmental disposal
– Dispose of packaging in an environmentally friendl
y manner.
– This appliance has been identified in accordance wit h the European Directive
2002/96/EEC on Waste Electrical and Electronic Equi pment (WEEE). The Directive
specifies a âframework for the return and recycling of waste applia nces and is valid
throughout Europe.
Scope of deliveryHumidity in the drum is caused byâthe final inspection.
Depending on the connection– A â24–40 mm dia. hose clip may also be required for connec ting the siphon (available from
specialist retailers). aPage â4 :Water connection
Useful tool– Spirit level for aligning the washer dryer.
– Wrench for adjusting the machine feet.
Water drainage
Power cord
Water supply
Covers
Hose holder
Aqua-Stop Aqua-Secure Standard
2
Installation area
– Stability is important to prevent the machine from
wandering.
– The installation area must be firm and level.
– Soft floors/floor coverings are not suitable.
– Ensure the area is well ventilated to achieve good drying performance.
If installing the appliance on a pedestal
– It is essential to secure the washer dryer feet with holding bracket sâ*.
If installing the appliance on a wooden joist floor
– If possible, install the washer dryer in a corner.
– Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.
– It is essential to secure the washer dryer feet with holding bracket sâ*.
* âorder no. WMZ 2200, WX 9756
Hose and cable lengths
Connection on left side orConnection on right side
Note: if hose holders are used, the hose lengths may be reduced.
Available from dealer/customer service:
– Aqua-Stop extension hose â**, approx. 2.50 m.
– Longer supply hose, approx. 2.20 m, for standard m odel.
**âorder no. WMZ 2380, WZ 10130
Built-under/Built-in appliance
Build-under/build-in before connection to the power supply.
Installed in between kitchen units (built-under or built-in)
– Dimension requirement of kitchen unit:
aâ= â650 âmm ,b â= â620 âmm ,câ= â850 âmm
– Install washer dryer only under a continuous workt op that
is connected firmly to the adjacent cupboards.
– The installation area must be well ventilated, othe rwise the
washer dryer will operate below optimum performance.
Dimension of ventilation cross-section:
d x e = 200 mm x 100 mm ,f = 365 âmm
Distance between wall and machine: 50âmm
~ 140 cm
~ 160 cm ~
140 cm
~
90 cm
~ 165 cm
~
95 cm
max. 100 cm
min. 60 cm
fe
3
Removing transport bolts
– Before using the appliance for the first time, alw
ays remove and retain
all 4 transport bolts.
– If transporting the appliance subsequently, always re-install the
transport bolts – this prevents damage to the machi ne. aPage â6
– Retain the screw and sleeve.
1. Take the hoses out of the holder and the elbow.
2.Undo and remove all 4 transport bolts.
3.Take the power cord out of the holders. Remove the sleeves.
4.Insert the covers and lock them in place by pressin g on the locking hook. Insert the hose
holders.
5. Fix the hoses in the hose holders.
4
Water connection
– Risk of electric shock! Do not immerse the Aqua-Sto p safety device in water
(contains âan âelectric valve).
– To prevent leakage or water damage, follow the ins tructions in this chapter.
– Attention : operate the washer dryer with cold drinking water only.
Do not connect to the mixer tap of a pressureless h ot-water heater.
– Do not use a used inlet hose. Only use the inlet h ose supplied or one which
was purchased from an authorised specialist dealer.
– If in doubt, have the appliance connected by a tec hnician.
Water supply
Water inlet hose:
Attention: do not kink, crush, modify or cut through (strengt h is no longer guaranteed).
Optimum water pressure in the mains: 100–1000 kPa (1 –10 bar)
– When the tap is turned on, the water flow is at lea st 8 l/min.
– If the water pressure is higher, install a pressur e reducing valve.
Model: Aqua-Stop
Aqua-Secure Standard
1. Connect the water supply hose to the tap.
Tighten plastic screw fittings by hand only.
2. Carefully turn on the tap and check that the
connection points are not leaking.
Attention: the screw connection is under
water mains pressure.
Water drainage
Water drainage hose:
Attention : do not kink or stretch.
Height difference between installation area and outlet: 60–100 cm
Drainage into a sink/bath tub:
Attention: secure the drainage hose to prevent it from slipping out
of âthe âsink.
Attention: the plug must not be in the plug hole. When the wa ter is being
pumped out of the washer dryer, check that the water drains away quickly
enough. Do not immerse the end of the drainage hose in the water that has
been pumped out. There is a risk that water will be dra wn back into the
washer dryer.
Drainage into a siphon:
Attention : secure the connection with a 24–40 mm dia. hose cl ip (available
from a specialist retailer).
Drainage into a plastic pipe with rubber sleeve:
Attention: Secure the drainage hose to prevent it from slippin g out
of âthe âdrain.
3/4 ’’
min. 10 mm
max.90°max.
90°
3/4 ’’
min 10 mm
5Manufacturer (see Operating instructions) 0810 / 9000 479252
Alignment
High levels of noise, intense vibrations and “wande ring” may be due to incorrect alignment.
Alignment will be carried out by customer service o r authorised technicians, if you want
to âalign the machine by yourself please use a spirit l evel.
Aligning the washer dryer with a spirit level.
1.Undo the lock nut in a clockwise direction using a wrench.
2. Adjust the height by turning the appliance foot.
All four appliance feet must be placed firmly on th e floor.
The washer dryer must not be able to wobble.
Check the alignment of the washer dryer with a spir it level andâ
correct if necessary.
3. Tighten the lock nut against the housing.
Hold the foot in place and make sure that the heigh t is not adjusted.
The lock nuts on all four appliance feet must be sc rewed tightly against
the housing.
Electrical connection
‘Connect the washer dryer to an alternating current via a correctly installed earthed socket
only.
‘The mains voltage and specifications on the washer dryer must match.
a Page â6: Technical specifications
‘For information about the connected load and requir ed fuse.
a Page â6: Technical specifications
‘Ensure that:
– the mains plug and socket are compatible,
– the cable cross-section is adequate,
– the earthing system has been installed correctly.
‘A damaged power cord may be replaced by an electrici an only.
A replacement power cord is available from customer service.
‘Do not use multiple plugs/connectors or extension ca bles.
‘If a residual current operated circuit-breaker is used, use only a type which guarantees
compliance with the currently valid regulations.
‘Mains plug:
– do not insert into/pull out of the socket with dam p hands.
– do not pull the plug out of the socket by pulling on the power cord.
– never pull out the plug while the appliance is in oper ation.
6
Transportation, e.g. if moving house
Before transporting the washer dryer:
1.Turn off the tap.
2. Release the water pressure in the supply hose. aPage â8: Filter in the water inlet hose
3. Drain any residual detergent solution. aPage â8: Drain pump
4. Isolate the washer dryer from the power supply.
5. Remove the hoses.
Installing transport bolts:
1.Remove the covers. If necessary, remove the
retainer according to the right picture.
2. Insert all 4 sleeves.
Clamp the power cord into
the holders.
Insert the screws and
tighten.
The transport bolts must be removed after transportation. aPage â3
To prevent unused detergent from flowing into the ou tlet during the next wash:
Pour 1 litre of water into dispenser II and start the Empty (Drain )or Spin programme.
Technical specifications
‘Dimensions (width x depth x height) 600 x 600 x 850 m m
‘Weight 84,5 kg
‘Power supplyNominal voltage 220–240
âV, 50 Hz
Max. current 10A
Max. washing power 2400 W
Max. drying power 1900 W
‘Water pressure 100–1000 kPa (1–10 bar)
‘Drain height 60–100 cm
‘Test programmes According valid European Standard EN 50229
1.
2.
7
Care
Machine housing, control panel
– Wipe with a soft, damp cloth.
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
– Immediately remove laundry and cleaning agent resi dues.
– Do not clean the appliance with a water jet.
Clean the detergent drawer ...
... if it contains detergent or fabric softener res idue.
1.Pull out the drawer up to the stop position, press down the latch
on âthe âinsert and remove the drawer completely.
2. Remove insert: pull insert upwards with finger.
3. Clean the detergent dispenser and the insert with w ater and a brush.
4. Refit the insert and secure in place (the cylinder s hould fit over the
guide âpin).
5. Insert the detergent drawer.
6. Leave the detergent drawer open so that residual wa ter can evaporate.
Drum
Leave the washer dryer door open after washing so t hat the drum can dry.
Rust stains – use chlorine-free cleaning agent, not steel wool.
Descaling No laundry in the machine!
This is not necessary if the detergent is dosed cor rectly. However, if it is necessary, follow the
instructions of the descaler manufacturer. Suitable descaling products can be purchased
from our website or after-sales service.
After-sales service
‘If you cannot rectify the fault yourself aOperating instructions, page 12, 13: What to do if...,
please contact our after-sales service. We will always find a suitable solution and will avoid a
visit from a service technician wherever possible.
‘The contact details for all countries can be found in the enclosed after-sales service directory.
‘Please give the after-sales service the product num ber (E-Nr.) and the production number
(FD) of the appliance.
Product number Production number You will find this information:
on the inside of the washer dryer door*/opened
service flap* and rear of the appliance.
*depending on the model
‘Rely on the professionalism of the manufacturer.
Please contact us.
This will ensure that the repair is carried out by trained service technicians who arrive
equipped with genuine spare parts for your appliance .
– Risk of electric shock!
Pull out the mains plug!
– Risk of explosion! No solvents!
8
Maintenance
Drain pump
Set the programme selector to Off, disconnect the mains plug.
1. Open and remove the service flap.
2.Release the drainage hose from the clip.
Remove the sealing plug from the drainage hose, all ow the detergent
solution to flow out. Push the sealing cap back in.
3. Remove the pump cap. Remove foreign objects/loose deb ris/fluff from
inside and clean the pump. (impeller in the pump must be able to rotate).
4.Clean any residual lye or fluff from the thread of the pump cap
and âpumphousing.
5. Attach the pump cap and screw it on tight until the s top, handle is upright.
Place the drainage hose back in the retainer.
6. Place the service flap back on and close.
To prevent unused detergent from flowing straight i nto the drain during
the next wash cycle: pour 1 litre of water into com partment II and start
the Spin programme. Then select and start a new washing progr amme
with detergent as usual.
Filter in the water inlet hose
Risk of electric shock
Do not immerse the Aqua-Stop safety device in water (it contains an electric valve).
Reduce the water pressure in the supply hose:
1. Turn off the tap.
2. Select any programme (except Spinor Empty (Drain )).
3. Touch Start button and allow the programme to run for approx. 40 seconds.
4. Set the programme selector to Off.Disconnect the mains plug.
Clean the filter:
1. Depending on model: Remove the supply hose from the tap.
Clean the filter with a small brush.
and/or on standard and Aqua-Secure models:
Remove the hose from the rear, remove the filter
using pliers and clean the filter.
2. Reconnect the supply hose and check if it
is tight.
– Risk of scalding!
Allow detergent solution to cool down!
– Turn off the tap!
9
Maintenance
Air inlet filter
Set the programme selector to Off, disconnect the mains plug.
1. Open and remove the service flap.
2.Remove the air inlet filter.
3.Clean the fluff on the air inlet filter with water and a brush.
4.Place the air inlet filter back on and close.
5.Place the service flap back on and close.
Aqua-Stop warrantyfor appliances with Aqua-Stop only
In addition to warranty claims against the seller b ased on the contract of sale and in addition
to our appliance warranty, we shall pay damages und er the following conditions:
1. If water damage was caused by a fault in our Aqua-Sto p system, we shall compensate private
users for damage.
2. The liability warranty applies to the service life of the appliance.
3. A claim can only be made under the warranty if the a ppliance and Aqua-Stop have been
correctly installed and connected according to our instructions; this also includes a correctly
installed Aqua-Stop extension (genuine accessory).
Our warranty does not extend to defective supply li nes or fittings up to the Aqua-Stop
connection on the tap.
4. Appliances which feature Aqua-Stop can be left unat tended during operation and it is not
necessary to turn off the tap afterwards.
The tap should only be turned off if you are away fo r a prolonged period, e.g. several weeks
holiday.
Contents Page
‹Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‹Environmental disposal . . . . . . . . . . . . . . . . . . . . . . . . . 1
‹Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‹Installation area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2‹Hose and cable lengths . . . . . . . . . . . . . . . . . . . . . . . . 2
‹Built-under/Built-in appliance . . . . . . . . . . . . . . . . . . . . . 2‹Removing transport bolts . . . . . . . . . . . . . . . . . . . . . . . 3
‹Water connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4‹Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
‹Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 5‹Transportation, e.g. if moving house . . . . . . . . . . . . . . . 6‹Technical specifications. . . . . . . . . . . . . . . . . . . . . . . . . 6
‹Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7‹After-sales serevice . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7‹Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8/9
‹Aqua-Stop warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Washer dryer
en
Read these instructions before switching on the washer dryer.
Also follow the separate Operating instructions.
Retain all documents for subsequent use or for the next o wner.
Installation maintenance
instructions
1
Safety instructions
– The washer dryer is heavy – take care when lifting it.
– Warning: frozen hoses may tear/burst. Do not insta ll the washer dryer outdoors or in areas
where there is a risk of frost.
– The washer dryer may be damaged. Do not lift by pr ojecting components (e.g. washer dryer
door).
– In addition to the instructions mentioned here, sp ecial regulations of the relevant water and
power supply companies may apply.
– If in doubt, have the appliance connected by a tec hnician.
– Lay hoses and cables in such a way that there is n o risk that they can be tripped over.
Environmental disposal
– Dispose of packaging in an environmentally friendl
y manner.
– This appliance has been identified in accordance w ith the European Directive
2002/96/EEC on Waste Electrical and Electronic Equi pment (WEEE). The Directive
specifies a âframework for the return and recycling of waste app liances and is valid
throughout Europe.
Scope of deliveryHumidity in the drum is caused byâthe final inspection.
Depending on the connection
– A â24–40 mm dia. hose clip may also be required for co nnecting the siphon (available from
specialist retailers). aPage â4 :Water connection
Useful tool
– Spirit level for aligning the washer dryer.
– Wrench for adjusting the machine feet.
Water drainage
Power cord
Water supply
Covers
Hose holder
Aqua-Stop Aqua-Secure Standard
2
Installation area
– Stability is important to prevent the machine from
wandering.
– The installation area must be firm and level.
– Soft floors/floor coverings are not suitable.
– Ensure the area is well ventilated to achieve good drying performance.
If installing the appliance on a pedestal
– It is essential to secure the washer dryer feet with holding bracke tsâ*.
If installing the appliance on a wooden joist floor
– If possible, install the washer dryer in a corner .
– Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.
– It is essential to secure the washer dryer feet with holding bracke tsâ*.
* âorder no. WMZ 2200, WX 9756
Hose and cable lengths
Connection on left side orConnection on right side
Note: if hose holders are used, the hose lengths may be reduced.
Available from dealer/customer service:
– Aqua-Stop extension hose â**, approx. 2.50 m.
– Longer supply hose, approx. 2.20 m, for standard m odel.
**âorder no. WMZ 2380, WZ 10130
Built-under/Built-in appliance
Build-under/build-in before connection to the power supply.
Installed in between kitchen units (built-under or built-in)
– Dimension requirement of kitchen unit: aâ= â650 âmm ,b â= â620 âmm ,câ= â850 âmm
– Install washer dryer only under a continuous workt op that
is connected firmly to the adjacent cupboards.
– The installation area must be well ventilated, oth erwise the
washer dryer will operate below optimum performance .
Dimension of ventilation cross-section:
d x e = 200 mm x 100 mm ,f = 365 âmm
Distance between wall and machine: 50âmm
~ 140 cm
~ 160 cm ~
140 cm
~
90 cm
~ 165 cm
~
95 cm
max. 100 cm
min. 60 cm
fe
a
â
â â
â â
â â
â â
‘
‘aâ
‘aâ
‘
‘
‘
‘
‘
â
â
â
aâ
â â
â
â
â
â â â â â â â â â
ââ
3
Removing transport bolts
– Before using the appliance for the first time, alw ays remove and retain
all 4 transport bolts.
– If transporting the appliance subsequently, always re-install the
transport bolts – this prevents damage to the machi ne. aPage â6
– Retain the screw and sleeve.
1. Take the hoses out of the holder and the elbow.
2.Undo and remove all 4 transport bolts.
3.Take the power cord out of the holders. Remove the sleeves.
4.Insert the covers and lock them in place by pressin g on the locking hook. Insert the hose
holders.
5. Fix the hoses in the hose holders.
4
Water connection
– Risk of electric shock! Do not immerse the Aqua-St op safety device in water
(contains âan âelectric valve).
– To prevent leakage or water damage, follow the ins tructions in this chapter.
– Attention : operate the washer dryer with cold drinking water only.
Do not connect to the mixer tap of a pressureless h ot-water heater.
– Do not use a used inlet hose. Only use the inlet h ose supplied or one which
was purchased from an authorised specialist dealer.
– If in doubt, have the appliance connected by a tec hnician.
Water supply
Water inlet hose:
Attention: do not kink, crush, modify or cut through (strengt h is no longer guaranteed).
Optimum water pressure in the mains: 100–1000 kPa (1–10 bar )
– When the tap is turned on, the water flow is at le ast 8 l/min.
– If the water pressure is higher, install a pressur e reducing valve.
Model: Aqua-Stop
Aqua-Secure Standard
1. Connect the water supply hose to the tap.
Tighten plastic screw fittings by hand only.
2. Carefully turn on the tap and check that the
connection points are not leaking.
Attention: the screw connection is under
water mains pressure.
Water drainage
Water drainage hose:
Attention : do not kink or stretch.
Height difference between installation area and out let: 60–100 cm
Drainage into a sink/bath tub:
Attention: secure the drainage hose to prevent it from slippi ng out
of âthe âsink.
Attention: the plug must not be in the plug hole. When the wa ter is being
pumped out of the washer dryer, check that the wate r drains away quickly
enough. Do not immerse the end of the drainage hose in the water that has
been pumped out. There is a risk that water will be drawn back into the
washer dryer.
Drainage into a siphon:
Attention : secure the connection with a 24–40 mm dia. hose cl ip (available
from a specialist retailer).
Drainage into a plastic pipe with rubber sleeve:
Attention: Secure the drainage hose to prevent it from slippin g out
of âthe âdrain.
3/4 ’’
min. 10 mm
max.90°max.90°
3/4 ’’
min 10 mm
â
â
‘
‘aâ
‘aâ
‘
‘
‘
‘
‘
â
â
â
aâ
â â
â
â
â
â â â â â â â â â
ââ
a â
â â
â â
â â
5Manufacturer (see Operating instructions) 0810 / 9000 479252
Alignment
High levels of noise, intense vibrations and “wande ring” may be due to incorrect alignment.
Alignment will be carried out by customer service o r authorised technicians, if you want
to âalign the machine by yourself please use a spirit l evel.
Aligning the washer dryer with a spirit level.
1. Undo the lock nut in a clockwise direction using a wrench.
2. Adjust the height by turning the appliance foot.
All four appliance feet must be placed firmly on th e floor.
The washer dryer must not be able to wobble.
Check the alignment of the washer dryer with a spir it level andâ
correct if necessary.
3. Tighten the lock nut against the housing.
Hold the foot in place and make sure that the heigh t is not adjusted.
The lock nuts on all four appliance feet must be sc rewed tightly against
the housing.
Electrical connection
‘Connect the washer dryer to an alternating current via a correctly installed earthed socket
only.
‘The mains voltage and specifications on the washer dryer must match.
a Page â6: Technical specifications
‘For information about the connected load and requir ed fuse.
a Page â6: Technical specifications
‘Ensure that:
– the mains plug and socket are compatible,
– the cable cross-section is adequate,
– the earthing system has been installed correctly.
‘A damaged power cord may be replaced by an electric ian only.
A replacement power cord is available from customer s ervice.
‘Do not use multiple plugs/connectors or extension cables.
‘If a residual current operated circuit-breaker is used, use only a type which guarantees
compliance with the currently valid regulations.
‘Mains plug:
– do not insert into/pull out of the socket with dam p hands.
– do not pull the plug out of the socket by pulling on the power cord.
– never pull out the plug while the appliance is in operation.
6
Transportation, e.g. if moving house
Before transporting the washer dryer:
1. Turn off the tap.
2. Release the water pressure in the supply hose. aPage â8: Filter in the water inlet hose
3. Drain any residual detergent solution. aPage â8: Drain pump
4. Isolate the washer dryer from the power supply.
5. Remove the hoses.
Installing transport bolts:
1. Remove the covers. If necessary, remove the
retainer according to the right picture.
2. Insert all 4 sleeves.
Clamp the power cord into
the holders.
Insert the screws and
tighten.
The transport bolts must be removed after transportation. aPage â3
To prevent unused detergent from flowing into the o utlet during the next wash:
Pour 1 litre of water into dispenser II and start the Empty (Drain )or Spin programme.
Technical specifications
‘Dimensions (width x depth x height) 600 x 600 x 850 mm
‘Weight 84,5 kg
‘Power supplyNominal voltage 220–240
âV, 50 Hz
Max. current 10A
Max. washing power 2400 W
Max. drying power 1900 W
‘Water pressure 100–1000 kPa (1–10 bar)
‘Drain height 60–100 cm
‘Test programmes According valid European Standard E N50229
1.
2.
7
Care
Machine housing, control panel
– Wipe with a soft, damp cloth.
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
– Immediately remove laundry and cleaning agent resi dues.
– Do not clean the appliance with a water jet.
Clean the detergent drawer ...
... if it contains detergent or fabric softener res idue.
1.Pull out the drawer up to the stop position, press do wn the latch
on âthe âinsert and remove the drawer completely.
2. Remove insert: pull insert upwards with finger.
3. Clean the detergent dispenser and the insert with w ater and a brush.
4. Refit the insert and secure in place (the cylinder should fit over the
guide âpin).
5. Insert the detergent drawer.
6. Leave the detergent drawer open so that residual wa ter can evaporate.
Drum
Leave the washer dryer door open after washing so t hat the drum can dry.
Rust stains – use chlorine-free cleaning agent, not steel wool.
Descaling No laundry in the machine!
This is not necessary if the detergent is dosed cor rectly. However, if it is necessary, follow the
instructions of the descaler manufacturer. Suitable descaling products can be purchased
from our website or after-sales service.
After-sales service
‘If you cannot rectify the fault yourself aOperating instructions, page 12, 13: What to do if...,
please contact our after-sales service. We will alw ays find a suitable solution and will avoid a
visit from a service technician wherever possible.
‘The contact details for all countries can be found in the enclosed after-sales service directory.
‘Please give the after-sales service the product num ber (E-Nr.) and the production number
(FD) of the appliance.
Product number Production number You will find this information:
on the inside of the washer dryer door*/opened
service flap* and rear of the appliance.
*depending on the model
‘Rely on the professionalism of the manufacturer.
Please contact us.
This will ensure that the repair is carried out by trained service technicians who arrive
equipped with genuine spare parts for your applianc e.
– Risk of electric shock!
Pull out the mains plug!
– Risk of explosion! No solvents!
â
‹‹
‹‹‹
‹‹
‹‹
‹‹‹
‹‹‹
‹
aâ
a â
aâ
‘
‘
‘â
‘
‘
‘
1.
2.
â â
â
‘a
‘
‘
‘
8
Maintenance
Drain pump
Set the programme selector to Off, disconnect the mains plug.
1. Open and remove the service flap.
2.Release the drainage hose from the clip.
Remove the sealing plug from the drainage hose, all ow the detergent
solution to flow out. Push the sealing cap back in.
3. Remove the pump cap. Remove foreign objects/loose d ebris/fluff from
inside and clean the pump. (impeller in the pump mu st be able to rotate).
4.Clean any residual lye or fluff from the thread of the pump cap
and âpumphousing.
5. Attach the pump cap and screw it on tight until the stop, handle is upright.
Place the drainage hose back in the retainer.
6. Place the service flap back on and close.
To prevent unused detergent from flowing straight i nto the drain during
the next wash cycle: pour 1 litre of water into com partment II and start
the Spin programme. Then select and start a new washing prog ramme
with detergent as usual.
Filter in the water inlet hose
Risk of electric shock
Do not immerse the Aqua-Stop safety device in water (it contains an electric valve).
Reduce the water pressure in the supply hose:
1. Turn off the tap.
2. Select any programme (except Spinor Empty (Drain )).
3. Touch Start button and allow the programme to run for approx. 40 seconds.
4. Set the programme selector to Off.Disconnect the mains plug.
Clean the filter:
1. Depending on model: Remove the supply hose from the tap.
Clean the filter with a small brush.
and/or on standard and Aqua-Secure models:
Remove the hose from the rear, remove the filter
using pliers and clean the filter.
2. Reconnect the supply hose and check if it
is tight.
– Risk of scalding!
Allow detergent solution to cool down!
– Turn off the tap!
9
Maintenance
Air inlet filter
Set the programme selector to Off, disconnect the mains plug.
1. Open and remove the service flap.
2.Remove the air inlet filter.
3.Clean the fluff on the air inlet filter with water and a brush.
4.Place the air inlet filter back on and close.
5.Place the service flap back on and close.
Aqua-Stop warranty for appliances with Aqua-Stop only
In addition to warranty claims against the seller based on the contract of sale and in addition
to our appliance warranty, we shall pay damages und er the following conditions:
1. If water damage was caused by a fault in our Aqua-Stop system, we shall compensate private
users for damage.
2. The liability warranty applies to the service life of the appliance.
3. A claim can only be made under the warranty if the appliance and Aqua-Stop have been
correctly installed and connected according to our in structions; this also includes a correctly
installed Aqua-Stop extension (genuine accessory).
Our warranty does not extend to defective supply li nes or fittings up to the Aqua-Stop
connection on the tap.
4. Appliances which feature Aqua-Stop can be left unat tended during operation and it is not
necessary to turn off the tap afterwards.
The tap should only be turned off if you are away f or a prolonged period, e.g. several weeks
holiday.
‹‹
‹‹‹
‹‹
‹‹
‹‹‹
‹‹‹
‹
aâ
a â
aâ
‘
‘
‘â
‘
‘
‘
1.
2.
â â
â
‘a
‘
‘
‘
â
Contents Page
‹Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‹Environmental disposal . . . . . . . . . . . . . . . . . . . . . . . . . 1
‹Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1‹Installation area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2‹Hose and cable lengths . . . . . . . . . . . . . . . . . . . . . . . . 2
‹Built-under/Built-in appliance . . . . . . . . . . . . . . . . . . . . . 2‹Removing transport bolts . . . . . . . . . . . . . . . . . . . . . . . 3
‹Water connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4‹Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
‹Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 5‹Transportation, e.g. if moving house . . . . . . . . . . . . . . . 6‹Technical specifications. . . . . . . . . . . . . . . . . . . . . . . . . 6
‹Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7‹After-sales serevice . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7‹Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8/9
‹Aqua-Stop warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Washer dryer
en
Read these instructions before switching on the was her dryer.
Also follow the separate Operating instructions.
Retain all documents for subsequent use or for the next o wner.
Installation maintenance
instructions