Bosch WKD 28540 User Manual

11
Programmes
Programme selector
The programme selector is used to set the washing and drying 
programmes.
The time remaining until the end of the programme and the 
Beladungsmenge (Load) are shown on the display panel.
Washing programmes*
*depends on the model
Resistentes/Algod. (Cottons/Coloureds)
Suitable for hard-wearing fabrics, heat-resistant fabrics made from cotton 
or linen.
– Coloureds up to 60 °C.
– Whites 60 °C to 90 °C.
Color eco/Cor eco (Cottons Eco)
Washing programme for the best possible...

12
Washing programmes*
* depends on the model
Clinic Wash ; 
For washing fabrics with increased hygiene requirements or those that will 
be used by allergy sufferers. The temperature remains constant during the 
washing process. More intensive rinsing with increased water level. For 
hard-wearing and easy-care fabrics made from cotton or linen.
Nocturno (Night Wash) 
Particularly quiet wash programme with a reduced final spin.
Sleep mode. Once the programme has finished, the display goes out, but 
can be...

13
Washing and drying options   
°C (Temperature) button
The temperature can be adjusted individually for each programme. 
To adjust it, press the °C (Temperature) button repeatedly until the 
required temperature is displayed.
B (Spin speed) button 
The spin speed can be individually adjusted for each programme.
To set the spin speed, press the B (Spin) button repeatedly until the 
required spin speed is displayed.
$ (Rinse hold) deactivates the spin function. The laundry remains in the 
rinsing water....

14
Secar (Drying) button 
The drying programmes –> page 12 can be individually adapted by 
selecting the drying options.
– Press the Secar (Drying) button repeatedly until the required drying 
option is shown on the display panel.
– To deactivate, press the Secar (Drying) button repeatedly until   
is shown on the display.
Drying options (symbols on the display panel)
0 Time-controlled 
dryingThe drying time can be set to between 2:40 and 0:00 by repeatedly pressing the 
Secar(Drying) button.
P Iron-damp...

15
Washing and drying 
Washing only
ˆTurn the programme selector to the desired programme, 
e.g. Resistentes/Algod. (Cottons/Coloureds) 60°C.
– The display panel alternately shows 2 (Remaining time) and the 
recommended load in kg. The % symbol flashes.
ˆIf necessary, adjust the temperature and the spin speed and select any 
options for your individualised programme, –> page 13.
–The Secar (Drying) function must not be activated.
ˆLoad the laundry –> page 8.
– Observe the maximum load, 
Programme table...

16
End of the programme
The washing and drying programmes are ended automatically.   
appears on the display panel.
ˆTurn the programme selector to Stop.
ˆRemove the washing from the drum.
ˆLeave the door open to allow the inside of the washer-dryer to dry out.
ˆTurn off the tap (not necessary on models with Aqua-Stop).
If the spin function was deactivated at the start of the wash cycle, 
$ (no final spin = laundry remains in last rinsing water), the washing 
programme is automatically stopped after the...

17
Cleaning and care
Safety information
Risk of electric shock
You must disconnect the appliance from the mains first. Never clean the 
washer-dryer with a water jet.
Risk of explosion.
Never clean the washer-dryer with solvents.
Risk of scalding
Hot washing water must be cooled before Draining.
Housing and control 
panel
Wipe with a soft, damp cloth. 
Remove detergent and cleaning agent residue immediately.
Do not clean with a jet of water.
Drum
Remove any foreign bodies from the drum and rubber seals....

18
Drain pump
ˆTake the Drain hose out of the retainer.
ˆRemove the plug from the Drain hose and release the washing water.
– The container for the Drained water may have to be emptied several 
times.
– When no more water runs out, replace the plug.
ˆPlace the Drain hose into the retainer.
ˆUnscrew the pump cover.
– Clean the pump housing and remove any foreign objects.
– Make sure that the impeller can turn freely.
ˆReplace the pump cover and screw firmly in place.
ˆPlace the kick panel in the 4 clip-in...

19
What to do if... 
Risk of electric shock.
Repairs must only be carried out by customer services or authorised 
technicians.
If repairs are needed, or if you cannot rectify a fault yourself with the help 
of the following table:
ˆSet the programme selector to Stop.
ˆDisconnect the washer-dryer from the power supply.
ˆTurn off the tap.
ˆCall the after-sales service –> page 22.
Other fault codes are only for use by the after-sales service. Make a note of the fault code to inform the after-
sales...

20 Water is not flowing in.The mains plug is not correctly 
plugged in.Plug in the mains plug correctly.
The door is not properly closed. Close the door.
The tap is not turned on. Turn on the tap.
The filter in the water supply hose is 
blocked.Clean the filter in the water supply hose 
–> page 18.
The water supply hose is pinched or 
kinked.Check the water inlet hose.
Intense vibrations during 
spinning.The washer-dryer is not correctly 
levelled.Level the washer-dryer –> page 25.
The transport safety...