Bosch Gts 10 J Manual

 English | 33
Bosch Power Tools1 609 92A 15R | (26.1.15)
When mounting the saw blade, pay attention that the 
cutting direction of the teeth (arrow direction on the 
saw blade) corresponds with the direction of the arrow 
on the blade guard!
–Mount the clamping flange 44 and the clamping nut 42.
– Turn the clamping nut 42 with the ring spanner 22 
(23 mm) and at the same time, pull the spindle lock lever 
43 until it engages.
– Tighten the clamping nut in clockwise direction 
(Tightening torque approx....

34 | English 
1 609 92A 15R | (26.1.15)Bosch Power Tools
Adjusting the Auxiliary Parallel Guide 
(see figure O)
When sawing narrow workpieces and bevel angles, the auxil-
iary parallel guide 37 must be mounted to parallel guide 10.
The auxiliary parallel guide can be mounted left or right to par-
allel guide 10 as required.
When sawing workpieces, these can become jammed be-
tween the parallel guide and the saw blade, be caught by the 
rotating saw blade, and be thrown from the machine.
Therefore, adjust...

 English | 35
Bosch Power Tools1 609 92A 15R | (26.1.15)
– Adjust the blade guard according to the workpiece height.
When sawing, the blade guard must always face lightly 
against the workpiece.
– Switch on the machine.
– Saw through the workpiece applying uniform feed.
– Switch off the machine and wait until the saw blade has 
come to a complete stop.
Sawing Bevel Angles
– Adjust the desired bevel angle. (see “Adjusting Bevel An-
gles”, page 33)
– Follow the worksteps in section “Sawing Straight Cuts”...

36 | English 
1 609 92A 15R | (26.1.15)Bosch Power Tools
Adjusting the Parallelism of the Parallel Guide 
(see figure W)
– Bring the power tool into the working position.
– Tilt the blade guard 6.x toward the rear to the stop.
– Loosen the clamping handle 35 of the parallel guide and 
slide it until it touches the saw blade.
Checking:
The parallel guide 10 must touch the saw blade over the com-
plete length.
Adjusting:
– Loosen the hex socket screws 71 using the supplied hex 
key 21.
– Carefully move the...

 English | 37
Bosch Power Tools1 609 92A 15R | (26.1.15)
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself, pull the mains 
plug.
If the replacement of the supply cord is necessary, this has to 
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Cleaning
– For safe and proper working, always keep the power tool 
and its ventilation slots clean.
– Remove dust and chips after each working procedure by 
blowing out with compressed...

38 | English 
1 609 92A 15R | (26.1.15)Bosch Power Tools
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: (031) 7012120
Fax: (031) 7012446
E-Mail: [email protected]
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: (021) 5512577
Fax: (021) 5513223
E-Mail: [email protected]
Bosch Headquarters
Midrand, Gauteng
Tel.: (011) 6519600
Fax: (011) 6519880
E-Mail: [email protected]
Disposal
The machine, accessories and packaging should be sorted...