Blomberg Wnf 7446 Users Manual

Washingmachine 
Vaskemaskine 
Pyykinpesukone 
Waschmaschine
User’s Manual  
Brugsanvisning 
Bedienungsanleitung 
Bruksanvisning
WNF 7446 A
WNF 7466 A
WNF 7466 S
WNF 7426 A
WNF 7406
 

2 - EN
1 Warnings
General Safety•	 Never	place	your	machine	on	a	carpet	covered	floor.	Otherwise,	lack	of	airflow	from	below	of	your	machine	may	cause	electrical	parts	to	overheat.	This	may	cause	problems	with	your	washing	machine.•	 If	the	power	cable	or	mains	plug	is	damaged	you	must	call	Authorized	Service	for	repair.•	 Fit	the	drain	hose	into	the	discharge	housing	securely	to	prevent	any	water	leakage	and	to	allow	machine	to	take	in	and	discharge	water	as	required.	It	is	very	important	that	the	water...

3 - EN
2 Installation
Removing packaging 
reinforcementTilt	the	machine	to	remove	the	packaging	reinforcement.	Remove	the	packaging	reinforcement	by	pulling	the	ribbon.
Opening the transportation locksA	Transportation	safety	bolts	must	be	removed	before	operating	the	washing	machine!	Otherwise,	the	machine	will	be	damaged!1.	 Loosen	all	the	bolts	with	a	spanner	until	they	rotate	freely	(“C”)2.	 Remove	transportation	safety	bolts	by	turning	them	gently.3.	 Fit	the	covers	(supplied	in	the	bag	with	the...

4 - EN
Electrical connectionConnect	the	machine	to	an	earthed	outlet	protected	by	a	fuse	of	suitable	capacity.
Important:•		 Connection	should	comply	with	national	regulations.•		 The	voltage	and	the	allowed	fuse	protection	are	specified	in	the	section	“Technical	Specifications”.•		 The	specified	voltage	must	be	equal	to	your	mains	voltage.•		 Connection	via	extension	cords	or	multi-plugs	should	not	be	made.B	A	damaged	power	cable	must	be	replaced	by	a	qualified	electrician.B	The	appliance	must	not	be...

5 - EN
5  Selecting a Program and Operating Your Machine
Control panelFigure 1
1	 -	 Spin	Speed	Adjustment	Button2	 -	 Display3	 -	 Temperature	Adjustment	Button	4	 -	 Program	Selection	Knob	5	 -	 On/Off	Button	
6	 -	 Time	Delaying	Button	(+/-)7	 -	 Auxiliary	Function	Buttons8	 -	 Start/Pause/Cancel	Button
Display symbols2.a	-	Spin	Speed	Indicator2.b	-	Temperature	Indicator2.c	-	Spin	Symbol2.d	-	Temperature	Symbol2.e	-	Remaining	Time	and	Delaying	Time	Indicator2.f	 -	Program	Indicator	Symbols...

6 - EN
Turning the machine onPlug	in	your	machine.	Turn	the	tap	on	completely.	Check	if	the	hoses	are	connected	tightly.	Place	the	laundry	in	the	machine.	Add	detergent	and	softener.	Press	the	“On/Off”	button.
Program selectionSelect	the	appropriate	program	from	the	program	table	according	to	type,	amount	and	degree	of	soiling	of	the	laundry	and	washing	temperatures.
Turn	the	Program	Selection	Knob	to	the	program	mode	that	you	wish	to	wash	your	laundry.
The	recommended	temperature	and	spin	speed	for	the...

7 - EN
rpm	in	the	default	setting	after	the	water	drains	from	the	machine.
C	Use	a	lower	spin	speed	for	delicate	laundries.Temperature selectionWhenever	a	new	program	is	selected,	the	temperature	anticipated	for	that	program	appears	on	the	temperature	indicator	(7b).
To	change	the	temperature,	press	the	temperature	button.	Temperature	decreases	in	10°	increments.
Cold	selection	is	shown	with	“-”	symbol.
90˚C	Normally	soiled,	white	cottons	and	linens.	(Ex.:	coffee	table	covers,	tablecloths,	towels,	bed...

8 - EN
Program and consumption table
•	:	Selectable
*	:	Automatically	selected,	not	cancellable.
**	:	Energy	Label	program	(EN	60456)
***	:	1400	rpm	in	machines	with	a	spin	speed	higher	than	1400	rpm.	It	spins	with	max.	rpm	in	machines	with	a	spin	speed	lower	than	1400	rpm.
-	:	See	program	description	for	maximum	load.
C	The	auxiliary	functions	in	the	table	vary	according	to	the	model	of	your	machine.C	Water	and	power	consumption	and	program	duration	differ	from	the	table	subject	to	changes	in	water...

9 - EN
Auxiliary functionsAuxiliary function selectionIf	an	auxiliary	function	that	should	not	be	selected	together	with	a	previously	selected	function	is	chosen,	the	first	selected	function	will	be	cancelled	and	the	last	auxiliary	function	selection	will	remain	active.
Ex.:	If	you	want	to	select	pre-wash	first	and	then	quick	wash,	pre-wash	will	be	cancelled	and	quick	wash	will	remain	active.
Auxiliary	function	that	is	not	compatible	with	the	program	cannot	be	selected.	(see,	“Program	Selection	Table”)•...

10 - EN
(prewash,	main	wash,	rinse,	softener	and	spin)	that	the	program	has	started	from	will	light	up.
Changing the selections after the program has startedThe	selected	spin	speed	and	program	temperature	fade	out.	An	empty	frame	appears.
When	the	“Program	selection”	button	is	brought	to	the	appropriate	position,	rpm	and	temperature	data	reappear.
Switching the machine to standby modeThe	machine	is	switched	to	standby	mode	by	pressing	“Start/Pause/Cancel”	button	momentarily.	The	Standby	symbol	which...