Black and Decker 12CUP PROGRAMMABLE COFFEEMAKER DCM901BKT User Manual

							1920
•	 Reheating	coffee	is	not	 recommended.	 Coffee	is	at	 its	 peak	 flavor	 immediately	
after brewing.
•	 Small	 oil	droplets	 on	the	 surface	 of	brewed,	 black	coffee	 is	due	 to	the	
extraction of oil from the coffee grounds. Oiliness may occur more frequently 
if heavily roasted coffees are used. Over extraction may also cause oiliness, 
indicating a need to clean your coffeemaker.
Care and Cleaning
This appliance requires little maintenance. It contains no user-serviceable parts. 
Any servicing requiring disassembly other than cleaning must be performed by a 
qualified appliance repair technician.
Warning: Unplug from wall outlet before cleaning.
1.  Always make sure the coffeemaker is unplugged and the warming plate is 
cool before attempting to clean.
2.  After daily use, the removable filter basket, carafe and carafe lid should be 
washed in warm, soapy water.
3.  If necessary, wipe the outside of the coffeemaker with a soft, damp cloth and 
wipe dry. Do not use abrasive cleansers, scouring pads or steel wool. Never 
immerse the coffeemaker in water or any other liquid.
CARING FOR  yOUR CARAFE
1.  Do not allow all liquid to evaporate from the carafe while on the warming 
plate, or heat the carafe when empty.
2.  Discard the carafe if damaged in any manner.
3.  Never use abrasive scouring pads or cleansers; they will scratch the glass.
4.  Avoid rough handling and sharp blows.
MINERAL  DEPOSITS  AND CLOGGING
Mineral deposits left by hard water can clog your coffeemaker. excessive 
steaming or a prolonged brewing cycle are signs that a cleaning is needed. 
Cleaning is recommended every 60 brewing cycles.
1.  Pour white into the carafe up to the 7-cup mark. Add cold water up to the   
12-cup mark. Pour the water/vinegar mixture into the water reservoir. 
2.  Place a permanent filter in the removable filter basket, then close the lid. 
Place the carafe on the warming plate. Press the ON/OFF button.
Note: During cleaning, more steam will occur than during normal brewing.
3.  KEEP THE COFFEEMAKER ON UNTIL HALF THE WATER HAS CYCLED 
THROUGH THE COFFEEMAKER, AS CAN BE VIEWED THROUGH THE 
WATER LEVEL INDICATOR. Press the ON/OFF button to turn the power off. 
When liquid stops dripping from the removable filter basket into the carafe, 
remove the carafe and allow the liquid to cool for 10 minutes. When cooled, 
pour liquid back into the water reservoir.
4.  Return carafe to the warming plate.
AUTO-ON FEATURE
To pre-set your coffeemaker to begin brewing at a later time, first follow steps 
1-5 in the Brewing Instructions section. Check to make sure that the clock is 
set to the correct time. If it is not, follow the above instructions to set the clock. 
Press the PROGRAM Button once, the LCD Display will flash “PROGRAM”. 
Press the HOUR and MIN Buttons until the desired brew time is reached. Make 
sure the proper “AM/PM” appears on the left side of the LCD display. Press 
the AUTO ON button. The green “AUTO” light will illuminate in the upper right 
corner and the pre-set brew time will be displayed momentarily, indicating that 
the coffeemaker is now waiting for the pre-set brew time to be reached before it 
begins the brewing cycle.
Note: If the AUTO ON button is pressed during the brewing process, the 
brewing will stop and the unit will turn off.
To Cancel Auto On: Press the AUTO ON button and the green light will shut off. 
To re-set the Auto On time so the unit will turn on at the same pre-set time the 
next day, press the AUTO ON button and the green “AUTO” light will illuminate.
Note: The Auto On feature will turn off after completing the brewing process at 
the pre-set brew time. The AUTO ON button must be pressed after each use in 
order for the unit to turn on at the same pre-set time the following day.
Note: In the event of a power outage or if the unit is unplugged, the clock will 
reset to 12:00 and the Auto On feature will have to be reprogrammed.
BREW STRENGTH FEATURE
Use the Brew Strength feature when you plan on brewing only a small amount 
of coffee. This feature slows down the brewing process so that the smaller 
amount of coffee will have the same taste quality as when you brew an entire 
carafe. The Brew Strength feature can be activated before the unit is turned ON 
or during the brewing process by pressing the BREW STRENGTH button. When 
this feature is activated, a coffee cup icon will be displayed in the LCD display.
Note: To deactivate the Brew Strength feature, press the BREW STRENGTH 
button again and the coffee cup icon will disappear.
AUTO SHUT
-OFF FEATURE
As an added convenience, your coffeemaker has been designed with an Auto 
Shut-Off feature. When the brewing cycle is complete, the coffeemaker will 
automatically shut off after 2 hours.
HINTS FOR GREAT T ASTING COFFEE
•	 A 	clean	 coffeemaker	 is	essential	 for	making	 great	tasting	 coffee.	 Regular	
cleaning, as specified in Care and Cleaning is highly recommended. Always 
use fresh, cool water in your coffeemaker. Finer grinds, such as drip and ADC 
coffee, promote fuller extraction and provide rich, full-bodied coffee. Regular 
grinds will require slightly more coffee per cup to provide the strength of a 
finer grind.
•	 Store	 coffee	in	a	cool,	 dry	place.	 Once	coffee	 has	been 	opened,	 keep	it	tightly	
sealed in the refrigerator to maintain freshness. For optimum coffee, buy 
whole beans and grind them just before brewing.
•	 Do	 not	re-use	 coffee	grounds	 since	this	will	greatly	 impair	coffee	flavor. 
						

							2122
NOTAS/NOTES5. Turn the coffeemaker back on and repeat this procedure, allowing all the 
cleaning solution to empty into the carafe. After dripping has stopped, discard 
contents in the carafe.
6.  After allowing the coffeemaker to cool for 10 minutes, rinse it out by brewing 
a carafe full of cold water. Make sure to insert the permanent filter into the 
removable filter basket before brewing.
7.  At the end of the brew cycle, turn OFF the unit by pressing the ON/OFF 
button. Discard water in the carafe. Remove the permanent filter and wash 
the carafe and removable filter basket in warm, soapy water. Rinse and dry.
8.  When the coffeemaker has cooled, wipe exterior with a dry cloth.  
						

							2324
NEED HELP?
For service, repair or any questions regarding your appliance, call the \
appropriate 800 
number on cover of this book. Please 
DO NOT return the product to the place of pur -
chase. Also, please  DO NOT mail product back to manufacturer, nor bring it to a service 
center. You may also want to consult the website listed on the cover of this manu\
al.
Two-y ear Limited Warranty 
(Applies only in the United States and Canada)
What does it cover?
•	 Any	defect	in	material	or	workmanship	provided;	however,	 Applica’s	liability	will	not		 	
  exceed the purchase price of product.
For how long?
•	 Two	years	after	date	of	purchase.
What will we do to help you?
•	 Provide	you	with	a	reasonably	similar	replacement	product	that	is	either	new	or	factory			
  refurbished.
How do you get service?
•	 Save	your	receipt	as	proof	of	date	of	sale.
•	 Visit	the	online	service	website	at	www.prodprotect.com/applica,	or	call	toll-free		 	
  1-800-231-9786, for general warranty service.
•	 If	you	need	parts	or	accessories,	please	call	1-800-738-0245.
What does your warranty not cover?
•	 Damage	from	commercial	use
•	 Damage	from	misuse,	abuse	or	neglect
•	 Products	that	have	been	modified	in	any	way
•	 Products	used	or	serviced	outside	the	country	of	purchase
•	 Glass	parts	and	other	accessory	items	that	are	packed	with	the	unit
•	 Shipping	and	handling	costs	associated	with	the	replacement	of	the	unit
•	 Consequential	or	incidental	damages	(Please	note,	however,	that	some	states	do	not		 	
  allow the exclusion or limitation of consequential or incidental damages\
, so this    
  limitation may not apply to you.)
How does state law relate to this warranty?
•	 This	warranty	gives	you	specific	legal	rights.	 You	may	also	have	other	rights	that	vary		 	
  from state to state or province to province.
¿NECESITA A yUDA?
Para servicio, reparaciones o preguntas relacionadas al producto, por favor 
llame al número del centro de servicio en el país donde usted compró su 
producto. NO devuelva el producto al fabricante. Llame o lleve el producto a un 
centro de servicio autorizado. 
DOS AÑOS DE GARANTÍA LIMITADA  
(No aplica en México, Estados Unidos o Canadá)
¿Qué cubre la garantía?
•	 La	 garantía	 cubre	cualquier 	defecto	 de	materiales	 o	de	 mano	 de	obra.	 Applica	
no se responsabiliza por ningún costo que exceda el valor de compra del 
producto.
¿Por cuánto tiempo es válida la garantía?
•	 Por	 dos	años	 a	partir	 de	la	fecha	 original	 de	compra.
¿Cómo se puede obtener servicio?
•	 Conserve	 el	recibo	 original	 de	compra.	
•	 Por	 favor	llame	 al	número	 del	centro	 de	servicio	 autorizado.	
Esta garantía  no cubre:
•	 Los	 productos	 que	han	sido	 utilizados	 en	condiciones	 distintas	a	las	 normales
•	 Los	 daños	 ocasionados	 por	el	mal	 uso,	 el	abuso	 o	negligencia
•	 Los	 productos	 que	han	sido	 alterados	 de	alguna	 manera
•	 Los	 daños	 ocasionados	 por	el	uso	 comercial	 del	producto
•	 Los	 productos	 utilizados	o	reparados	 fuera	del	país	 original	 de	compra
•	 Las	 piezas	 de	vidrio	 y	demás	 accesorios	 empacados	 con	el	aparato
•	 Los	 gastos	 de	tramitación	 y	embarque	 asociados	al	reemplazo	 del	producto
•	 Los	 daños	 y	perjuicios	 indirectos	 o	incidentales 
						

							Sello del Distribuidor:
Fecha de compra:
Modelo:
2526
Póliza de Garantía 
(Válida sólo para México)
Duración 
Applica Manufacturing, S. de R. L. de C.V. garantiza este producto por 2 años 
 
a partir de la fecha original de compra.
¿Qué cubre esta garantía?
Esta Garantía cubre cualquier defecto que presenten las piezas, componentes 
y la mano de obra contenidas en este producto.
Requisitos para hacer válida la garantía
Para reclamar su Garantía deberá presentar al Centro de Servicio Autorizado 
la póliza sellada por el establecimiento en donde adquirió el producto. Si no la 
tiene, podrá presentar el comprobante de compra original.
¿Donde hago válida la garantía?
Llame sin costo al teléfono 01 800 714 2503, para ubicar el Centro de Servicio 
Autorizado más cercano a su domicilio en donde usted podrá encontrar partes, 
componentes, consumibles y accesorios.
Procedimiento para hacer válida la garantía
Acuda al Centro de Servicio Autorizado con el producto con la póliza de 
Garantía sellada o el comprobante de compra original, ahí se reemplazará 
cualquier pieza o componente defectuoso sin cargo alguno para el usuario 
final. Esta Garantía incluye los gastos de transportación que se deriven de su 
cumplimiento.
Excepciones
Esta Garantía no será válida cuando el producto:
A)  Se hubiese utilizado en condiciones distintas a las normales.
B)  No hubiese sido operado de acuerdo con el instructivo de uso que le 
acompaña.
C)  Cuando el producto hubiese sido alterado o reparado por personas no 
autorizadas por  Applica Manufacturing, S. de R. L. de C.V.
Nota: Usted podra encontrar partes, componentes, consumibles y accesorios 
en los centros de servicios autorizados. Esta garantía incluyen los gastos 
de transportación que se deriven de sus cumplimiento dentro de sus red de 
servicio.
Argentina
Servicio Central Attendace 
Monroe 3351 Ciudad 
Autónoma de Bs. As. 
Buenos Aires Argentina  
Tel. 0810-999-8999
Chile
Servicio Máquinas y 
Herramientas Ltda. 
Rosario Norte #24 A   
Santiago, Chile  
Tel.: (800) 401 400
Colombia
PLINARES 
Tel. sin costo 01 800 7001870
Costa Rica
Tel.: (800) 293 4663
Ecuador
Servicio Master de Ecuador  
Av. 6 de Diciembre 9276   
y los Alamos 
Tel. (593) 2281-3882
El Salvador
Calle San Antonio Abad 2936  
San Salvador, El Salvador  
Tel. (503) 2284-8374
Guatemala
MacPartes SA  
3ª Calle  414 Zona 9 
Frente a Tecun   
Tel. (502) 2331-5020  
  2332-2101
    Honduras
ServiTotal 
Contigua a Telecentro
 
Tegucigalpa, Honduras, 
Tel. (504) 235-6271
México
Articulo 123 # 95 Local 109 
y 112 
Col. Centro, Cuauhtemoc,   
México, D.F. 
Tel. 01 800 714 2503
Nicaragua
ServiTotal 
De semáforo de portezuelo  
500 metros al sur. 
Managua, Nicaragua, 
Tel. (505) 248-7001
Panamá
Servicios Técnicos CAPRI 
Tumbamuerto Boulevard   
El Dorado Panamá  
500 metros al sur. 
Tel. (507) 2360-236  
       (507) 2360-159
Perú
Servicio Central Fast Service 
Av. Angamos Este 2431  
San Borja, Lima Perú 
Tel. (511) 2251 388
Puerto Rico
Buckeye Service 
Jesús P. Piñero #1013 
Puerto Nuevo, SJ PR  00920  
Tel.: (787) 782-6175 Republica Dominicana
Plaza Lama, S.A.
Av, Duarte #94
Santo Domingo, 
 
República Dominicana
Tel.: (809) 687-9171
Venezuela
Inversiones BDR CA  
Av. Casanova C.C.   
City Market Nivel Plaza Local 
153 
Diagonal Hotel Melia, 
Caracas. 
Tel. (582) 324-0969
www.applicaservice.com
[email protected]
Por favor llame al número correspondiente que aparece en la lista a continuación para solicitar 
que se haga efectiva la garantía y donde Ud. puede solicitar servicio, reparaciones o partes en 
el país donde el producto fué comprado. También puede consultarnos en el e-mail. servicio@
applicaservice.com
Comercializado por:
Applica Manufacturing S. de R.L de C.V  Presidente Mazarik No111, 1er Piso
Col. Chapultepec Morales, Mexico D.F       Delegacion Miguel Hidalgo CP 11570Mexico
Servicio y Reparación
Newton #133 Locales A y B Col. Chapultepec Morales C.P. 11570
Mexico, DF.
Servicio al Consumidor,
Venta de Refacciones y Accesorios 01 800 874 2503 
						

							marca registrada de The Black & Decker Corporation, Towson, Maryland, E.U. A trademark of The Black & Decker Corporation, Towson, Maryland, USA
2008/6-24-112S/E
950  W  120 V
CAT. NO. EHB500
TYPE  1  160  W  1
AC  ONLY          6
60 Hz
950  W  220 V
CAT. NO. EHB500
TYPE  1  160  W  1
AC  ONLY          6
50/60 Hz
El símbolo de un rayo indica voltaje 
peligroso. El signo de exclamación 
indica  importantes instrucciones de 
mantenimiento. Consulte a    continuación:
PRECAUCIóN:   Para reducir el riesgo 
de incendio o de choque eléctrico, no 
retire la cubierta de la cafetera.   
No contiene por dentro partes 
reparables por el consumidor. Cualquier 
reparación deberá ser efectuada 
únicamente por personal autorizado.  The lightning symbol refers to 
“dangerous 
  voltage”; the exclamation 
symbol refers to   
maintenance 
instructions. See below.
WARNING:  To reduce the risk of fire   
or    electric shock, do not remove the 
cover of the   
coffeemaker. There are   
no user-serviceable parts inside. Repair 
should be done by    authorized service 
personnel only.
PRECAUCIóN / WARNING
RIESGO DE INCENDIO O DE CHOQUE ELÉCTRICO. NO ABRA.
RISK OF FIRE OR ELECTRIC SHOCK. DO NOT OPEN.
Código de fecha / Date Code
Copyright © 2008 Applica Consumer Products, Inc. Fabricado en la República Popular de ChinaImpreso en la República Popular de China
Importado por / Imported by:Applica Americas, Inc.
Av. Juan B Justo 637 Piso 10
(C1425FSA) Ciudad Autonoma de Buenos Aires Argentina
C.U.I.T No. 30-69729892-0
Importado por/ Imported by:   
APPLICA  MANUFACTURING  S. DE R. L.  DE  C. V.
Presidente Mazarik No111, 1er Piso
Col. Chapultepec Morales, Mexico D.F Deleg. Miguel HidalgoCP 11570Mexico
Del interior marque sin costo  01 (800)  744 4444
Made in People’s Republic of China
Printed in People’s Republic of China