Bissell Proheat Model 7901-r Manual

11
Carpet Cleaning
1.
2.
3.
4.
5.
6.
7.
ATTENTION
BERBER CARPET
OWNERS:
Some Berber Carpets have a
tendency to fuzz with wear.
Repeated strokes in the 
same area with an ordinary
vacuum or deep cleaner may
aggravate this condition.
Please see Stain Removal
instructions on page 12.
Plug into a proper outlet and turn the Power and the
SmartTemp switches ON. Wait two minutes for the
heater to warm up before beginning to clean.
While pressing the trigger, make one slow forward wet
pass and another one back....

12
Stain Removal
Do Not Delay! Failure to attend to an accident soon after it occurs
may cause it to set and become permanent.
Before treating any stain, follow these pre-treatment steps:
Blot up liquids with an absorbent cloth or paper towels.
White materials are recommended because certain dyes
may bleed and make the stain worse.
Gently scrape up semi-solids with a spoon or spatula. Do
not use a knife or other utensil with sharp edges
because it could damage the carpet or upholstery.
If the area has...

13
(Available on select models only)
The Perfect Pass feature is designed to help you achieve the best
cleaning results when deep cleaning.
Apply smooth even strokes when deep cleaning your 
carpets. An upright deep cleaner should not be used at
the same speed as an ordinary vacuum. That is too fast
for optimum cleaning results.
The Perfect Pass indicator displays a red light which tells
you if you are in the range of Best Cleaningor if you
are going Too Fast. If you notice consistently that the...

14
The Scotchgard protector applicator (with formula included) can be used to
help retain the carpet cleanliness you achieve with your ProHeat Pro-Tech
machine. For best results the post cleaning treatment should be applied
while the carpet is still wet or damp. It is recommended that the Scotchgard
Protector is applied every  12 months in all carpeted areas, and after every
deep cleaning for high traffic areas such as entryways and stairs.
Immediately after cleaning and rinsing your carpets, empty the...

15
Tip:
Deep cleaning 
carpeting and
upholstery with
BISSELL Multi-
Allergen Removal
™
Formula regularly
can reduce dust
mite waste and
allergens in your
home.
Check manufacturer’s tag before cleaning. “W” or “WS” on the
tag means you can use your ProHeat Pro-Tech. If the tag is
coded with “X” or “S” (with a diagonal strike through), or says
“Dry Clean Only,” do not proceed. The Scotchgard
™protectant
is not recommended for use on velvet, silk, 100% cotton
upholstery, vinyl or leather. If manufacturer’s...

16
The Bare Floor Tool (available with select models only) 
provides effective cleaning for linoleum, vinyl, and tile floors.
Caution: Do not use on hardwood floors 
Use BISSELL Floor Cleansing Formula.
Vacuum or sweep thoroughly to pick up loose debris and pet hair.
Remove easily moved furniture from the room, (chairs, tables, etc.)
Plan your cleaning route to leave an exit path.
Plan activities to allow 30 minutes for the floor to dry completely.
Step on the handle release to lay the machine handle...

17
Routine Maintenance
Slowly move the machine nozzle with Bare Floor Tool 
forward and back over soiled surface one time while 
pressing the trigger.Caution: Do not over wet.
Repeat the motion without pressing the trigger using the Bare
Floor Tool to squeegee and suction up the dirty water.
Repeat steps 1 and 2 backing along the exit path.
Allow about 30 minutes for the floor to dry completely.
When the cleaning job is complete refer to the
Maintenance/Storagesection on page 17-20.
To remove Bare Floor...

18
Turn the machine off and unplug from the wall outlet.
Step on the release pedal and recline the handle down onto
floor. (see illustration).
Remove Tank-In-Tank and SmartMix tanks. Set them aside
(see illustration).
Remove Belt Access Door located near the Floor Cleaning/
Tools switch by inserting a flat head screwdriver into the slot
nearest to the handle and gently prying the access door off
(see illustration).
Turn the machine onto its side so the belt access area is 
facing upward (see...

19
To Install the Replacement Pump Belt
With the unit still on its side, loop one end of the replacement
pump belt around the red pump pulley and then the other end
around the silver motor shaft (see illustration). Do not twist the
replacement pump belt.
Re-install the toothed brush belt first onto the red pump pulley
and then onto the toothed end of the brush (see illustration).
Re-Install the brush into the base of unit.
Place the black brush arm onto the brush and slide black
brush arm into base of...

20
WARNING: To reduce the risk of
fire, electric shock or
injury unplug from outlet
before servicing.
Troubleshooting
SmartTemp Ready Light does not illuminate.
Possible Causes Remedies
The SmartTemp switch is not Turn on the SmartTemp switch.
turned ON.
The machine Power Switch is not  Both switches must be ON to
turned ON. activate the SmartTemp Ready Light.
Reduced spray or no spray
Possible Causes Remedies
Bladder may be empty. Refill bladder with hot tap water.
SmartMix bottle may be empty.Fill with...