Bissell 93002 User Manual

							Operations
3. if th\b ar\ba has alr\bady dri\bd, s\bparat\b and 
r\bmov\b from th\b carp\bt what\bv\br s\bmi-solids 
and r\bsidu\b that can b\b acc\bss\bd b\bfor\b d\b\bp 
cl\baning. 
4.  b\b sur\b to t\bst any spot r\bmoval formulas in 
an inconspicuous ar\ba first. This is important as 
som\b dy\bs and mat\brials could b\b damag\bd or 
discolor\bd by cl\baning solv\bnts.  if such a chang\b  
should occur, try a diff\br\bnt solution or call a 
prof\bssional.
5.  if cl\baning on  b\brb\br carp\bting, g\bntly run 
your machin\b ov\br a hidd\bn ar\ba.   
if no fuzzing occurs, continu\b cl\baning   
in soil\bd ar\ba.
6.  Using th\b  bissell stain Pr\bTr\bat, spray 
\bv\bnly ov\br soil\bd ar\ba. Do not ov\brw\bt. Wait 
3-5 minut\bs. G\bntly work th\b solution by blotting 
ar\ba with a cl\ban, damp, color saf\b cloth.
7.   Cl\ban using \bith\br th\b Fl OOR CleANiNG, or 
TOOls s\btting on th\b R\badyTools dial.
c\beaning with the Stain  trapper  too\b
1.  Attach th\b  stain Trapp\br tool to th\b \bnd   
of th\b hos\b.
2.  G\bntly scrap\b up any s\bmi-solids with a spoon 
or spatula. Do not us\b a knif\b or oth\br ut\bnsil 
with sharp \bdg\bs b\bcaus\b it could   
damag\b th\b carp\bt or upholst\bry.
3.  Plug in and turn on th\b pow\br switch.
4.  Cl\ban by pr\bssing th\b trigg\br to spray solu-
tion onto th\b ar\ba to b\b cl\ban\bd.  slowly mov\b 
th\b tool back and forth ov\br th\b soil\bd surfac\b. 
R\bl\bas\b th\b trigg\br to suction soil\bd wat\br. 
Continu\b to cl\ban in th\b ar\ba, working in small 
s\bctions, until no mor\b dirt can b\b r\bmov\bd. 
Rins\b (optional) and suction as n\b\bd\bd. 
ca UtIon: Do not overwet.
notE: Do not fi\b\b the Stain  trapper tank   
above the  fUll \bine.
5.  To \bmpty th\b  stain Trapp\br tool, rotat\b   
th\b small tank on th\b bottom of th\b tool   
to unlock it. 
notE:  \fe carefu\b to keep the top of the too\b 
facing upward or soi\bed water wi\b\b spi\b\b out of 
the tank.
6.  Dump dirty wat\br into a sink or toil\bt and   
rins\b th\b tank out with cl\ban wat\br. R\bplac\b   
th\b tank by lining up th\b “unlock” symbol with 
th\b small arrow on th\b tank and turning it to   
th\b “lock” symbol. 
7.   Cl\ban th\b front of th\b tool by r\bmoving th\b 
plat\b ov\br th\b suction path. Pull down on th\b 
bottom of th\b plat\b to r\bmov\b. Run th\b tool   
and th\b plat\b und\br cl\ban wat\br to rins\b taking 
car\b to r\bmov\b all d\bbris. R\bplac\b th\b front   
plat\b by sliding it back into plac\b. 
www.bissell.com
   
   800.237.769111
7.
5. 
						

							Operations
Hard f\boor c\beaning
(Se\bect mode\bs on\by)\four PROh\bat 2X mod\bl may hav\b com\b with 
a hard floor attachm\bnt and 2X Hard Floor 
solutions Formula. if not, th\bs\b products 
ar\b availabl\b for purchas\b by contacting th\b 
bissell Consum\br Car\b d\bpartm\bnt by phon\b 
or at th\b w\bbsit\b. Th\b hard floor tool provid\bs 
\bff\bctiv\b cl\baning for linol\bum, vinyl, and   
til\b floors. Caution: Do not us\b on uns\bal\bd 
hardwood floors.
1.  Vacuum or sw\b\bp thoroughly to pick up any 
loos\b d\bbris and p\bt hair.
2.  Mov\b any furnitur\b, if n\b\bd\bd.
3.  Fill th\b formula tank to “WATeR” lin\b with 
wat\br. Fill to “FORMUlA” lin\b with  bissell 2X 
Hard Floor  solutions.
4.  Fill th\b 2-in-1 wat\br tank with hot tap wat\br 
and s\bt asid\b.
5.  Attach th\b hard floor tool onto th\b bottom of 
th\b machin\b by hooking it into th\b nozzl\b and 
swinging it down until it clicks into plac\b. 
6.  s\bt R\badyTools dial to th\b “Fl OOR 
CleANiNG” s\btting.
7.   s\bt th\b Custom Cl\ban dial to NORMAl cl\ban.
8.  Plug into an outl\bt and turn th\b pow\br switch 
and h\bat\br ON (  I ).
9.  slowly mov\b th\b machin\b forward and   
back ov\br hard floor surfac\b on\b tim\b whil\b 
d\bpr\bssing trigg\br.  Caution: Do not overwet.
10.  R\bp\bat th\b motion without pr\bssing th\b   
trigg\br using th\b hard floor tool to squ\b\bg\b\b   
and suction up th\b dirty wat\br.
11.  Allow ad\bquat\b tim\b for floors to dry.
12.  R\bmov\b hard floor tool, rins\b and dry   
b\bfor\b storing.
13.  Rins\b out th\b formula tank.
www. bissell.com
   
   800.237.769112
W
aRnInG
To reduce the risk of fire and electric shock- when  
cleaning a hard floor, the BISSELL hard floor tool  
203-5642 must be used and it must only be used with 
BISSELL 2X Hard Floor Solutions cleaning fluid intended   
for use with this appliance.
5. 
						

							Maintenance & Care
machine storage
Onc\b your cl\baning is compl\bt\b, mak\b sur\b th\b 
2-in-1 wat\br tank is \bmpti\bd, rins\bd out, and 
dri\bd b\bfor\b th\b n\bxt us\b. Th\b formula tank can 
r\bmain fill\bd and r\bady to go.
notE: Store c\beaner in a protected, dry area. 
Since this product uses water, it must not be 
stored where there is a danger of freezing. 
freezing wi\b\b damage interna\b components and 
void the warranty.
machine care
For b\bst r\bsults, a f\bw simpl\b st\bps can assur\b 
your machin\b is w\bll maintain\bd  
aft\br your cl\baning is compl\bt\b.
1.  Flush your machin\b of any r\bmaining r\bsidual 
solution.
    a. Fill th\b 2-in-1 cl\ban wat\br tank with cl\ban 
hot tap wat\br.
   \b .   Plug your machin\b into a prop\br outl\bt 
and s\bt th\b Custom Cl\ban dial to th\b rins\b 
s\btting. Turn th\b pow\br on by pr\bssing th\b 
pow\br button. 
   c .  R\bclin\b th\b handl\b and pr\bss th\b spray 
trigg\br for 15 s\bconds whil\b making forward 
and backward pass\bs on carp\bt. R\bl\bas\b th\b 
trigg\br to suction. R\bp\bat for anoth\br 15 s\bc-
onds. Continu\b without pr\bssing th\b trigg\br 
until th\br\b is no mor\b wat\br b\bing suction\bd.
2.  Turn pow\br and h\bat\br switch\bs OFF (O). 
Unplug th\b machin\b and wrap th\b pow\br cord. 
empty th\b 2-in-1 wat\br tank.
3.  Rins\b out 2-in-1 wat\br tank, with running hot 
tap wat\br, taking car\b to cl\ban und\brn\bath th\b 
h\bavy duty bladd\br, and all around it.  
4.  Th\b top half of th\b tank can b\b rins\bd cl\ban 
through th\b nozzl\b ar\ba. Also, pop out th\b r\bd 
filt\br und\brn\bath th\b top half of th\b tank and 
rins\b out. R\bplac\b b\bfor\b putting th\b top and   
bottom halv\bs of th\b tank tog\bth\br.
www.bissell.com
   
   800.237.769113
W
aRnInG
To reduce the risk of electric shock, turn power switch 
off and disconnect plug from electrical outlet before 
performing maintenance or troubleshooting checks.
»  Let all parts 
dry completely 
before storing
Ti p
3 & 4Filt\br  
						

							Maintenance & Care
5. b\bfor\b you plac\b th\b cl\ban\bd 2-in-1 wat\br tank 
back onto th\b machin\b, r\bmov\b th\b r\bd solution 
filt\br cap (on th\b bas\b of th\b machin\b).R\bmov\b 
th\b cap by ins\brting a coin or a flat h\bad scr\bw 
driv\br into th\b slot on th\b top. Turn count\br clock 
wis\b and unscr\bw.  s\bt asid\b.
   a .  R\bmov\b th\b whit\b filt\br by grasping th\b 
post and pulling up and out of th\b unit. 
Rins\b th\b filt\br und\br cold wat\br.
notE:  \fe carefu\b not to drop the fi\bter into the 
sink or disposa\b.
   \b .  R\bplac\b th\b whit\b filt\br back into th\b   
filt\br ar\ba. 
notE:  make sure the white fi\bter is seated prop-
er\by before p\bacing the red so\bution fi\bter cap.
   c .  R\bplac\b th\b r\bd solution filt\br cap and 
turn clockwis\b to tight\bn.
6.  K\b\bping th\b 2-in-1 wat\br tank off of th\b bas\b 
of th\b machin\b, simply unscr\bw th\b floor nozzl\b 
using a Phillips h\bad scr\bwdriv\br. This can b\b 
rins\bd out  at th\b fauc\bt. Th\bn r\bplac\b back onto 
th\b machin\b by starting from th\b bottom of th\b 
nozzl\b and hooking th\b tabs into th\b hol\bs on 
th\b bottom sid\bs of th\b machin\b.  s\bcur\b into 
plac\b with th\b scr\bw. 
7.   Th\b insid\b of th\b \bnd caps by th\b brush rolls 
can b\b wip\bd out with a cl\ban pap\br tow\bl, 
or, if a mor\b thorough cl\baning is d\bsir\bd, th\b 
\bnd caps can b\b tak\bn off using a Phillips h\bad 
scr\bwdriv\br and rins\bd cl\ban. R\bplac\b aft\br 
cl\baning.
8.  Any loos\b hair or d\bbris can b\b pull\bd from  
th\b brush rolls and thrown away. For th\b most 
thorough cl\ban b\bfor\b storag\b, follow dir\bctions 
for r\bmoval and r\bplac\bm\bnt of th\b brush rolls 
and b\blts.
9.  To cl\ban attachm\bnts that may hav\b b\b\bn us\bd, 
r\bmov\b from hos\b and rins\b und\br cl\ban, running 
wat\br. Dry and r\bplac\b attachm\bnt in th\b tool 
caddy. Cl\ban th\b hos\b by suctioning cl\ban wat\br 
from th\b tap.  b\bfor\b r\bplacing, lift \bnd of hos\b and 
str\btch out to \bnsur\b all wat\br is cl\bar\bd from hos\b. 
R\bf\br to pag\b 10.
10.  Aft\br carp\bt is dry, vacuum again to r\bmov\b 
hair and fuzz.
www. bissell.com
   
   800.237.769114
solution 
 
Filt\br Cap
Filt\br
5a. 5b.
5c.
6.
W aRnInG
To reduce the risk of electric shock, turn power switch 
off and disconnect plug from electrical outlet before 
performing maintenance or troubleshooting checks. 
						

							Sma\b\b be\bt remova\b and rep\bacement
Occasional r\bplac\bm\bnt of on\b or both b\blts 
may b\bcom\b n\bc\bssary. if that is n\b\bd\bd, pl\bas\b 
follow th\b instructions b\blow.
1.  Turn off th\b machin\b, and unplug it from   
th\b outl\bt.
2.  R\bmov\b both th\b 2-in-1 wat\br tank and th\b 
formula tank.  s\bt asid\b.
3.  Unscr\bw th\b front nozzl\b and r\bmov\b it.   
s\bt asid\b.
4.  Turn th\b machin\b on its sid\b.   
IMPORTANT: cord side down.
5.  R\bmov\b th\b cl\bar \bnd cap by unscr\bwing th\b 
2 black scr\bws. Tak\b car\b not to drop th\b scr\bws 
into th\b unit.
6.  R\bmov\b 1 silv\br scr\bw.
7.   R\bmov\b pivot arm by g\bntly lifting up.
8.  R\bmov\b small brush b\blt.
9.  R\bplac\b small brush b\blt, and r\bv\brs\b   
st\bps abov\b.
\frush remova\b and \barge be\bt rep\bacement 
brush\bs can b\b r\bmov\bd for cl\baning or   
r\bplac\bm\bnt as n\b\bd\bd. 
1.  Follow small b\blt r\bmoval instructions abov\b.
2.  R\bmov\b brush rolls by pulling th\bm off of 
th\b m\btal rods.  Be careful not to lose the small 
washer at each end of the \brush rolls.
3.  Plac\b cl\ban\bd or n\bw brush rolls back onto 
th\b rods. Mak\b sur\b on\b wash\br is on \bach \bnd 
of th\b roll\brs prior to sliding onto th\b rod.  b\b 
sur\b to l\bt th\b rod slid\b through th\b bushing to 
insur\b prop\br fit.
4.  R\b-attach th\b long b\blt on th\b bottom to th\b 
cogs of th\b small roll\br brush\bs.
5.  Plac\b small b\blt ov\br back roll\br and m\btal 
cog.
6.  Plac\b pivot arm in plac\b and scr\bw in plac\b 
using th\b silv\br scr\bw.
7.   R\b-attach cl\bar \bnd cap by tight\bning with th\b 
(2) black scr\bws.
8.  R\bturn front nozzl\b to front of unit, by latching 
from und\brn\bath and th\bn s\bcuring with a scr\bw.
if you hav\b any qu\bstions or ar\b having troubl\b 
installing or r\bplacing your b\blt(s) or brush\bs, 
pl\bas\b call  BI\f\fELL Consumer Care.2.
4.
6.
8. 3.
5.
7.
Maintenance & Care
www.
bissell.com
      800.237.769115
3.
7.
9.
6.
8.
W aRnInG
To reduce the risk of electric shock, turn power switch 
off and disconnect plug from electrical outlet before 
performing maintenance or troubleshooting checks.
5.  
						

							Troubleshooting
prob\bempossib\be causes Remedies
\fui\bt-in heater 
ready \bight 
does not  
i\b\buminate Th\b h\bat\br switch is not turn\bd 
ON ( 
i ) Turn th\b h\bat\br switch ON ( 
i )
Th\b pow\br switch is not turn\bd 
ON (  i ) both switch\bs must b\b ON ( 
i ) to 
activat\b th\b h\bat\br r\bady light
Reduced 
spray or   
no spray Wat\br tank may b\b \bmpty
Fill h\bavy duty bladd\br with hot tap wat\br
Formula tank may b\b \bmpty
Fill formula tank with bissell 2X 
Formula for cl\baning
Tank may not b\b s\bat\bd compl\bt\blyTurn pow\br OFF (0). R\bmov\b and r\bs\bat tank
Pump may hav\b lost prim\b.Turn pow\br OFF (0) and th\bn back ON 
(i). Wait on\b minut\b, th\bn d\bpr\bss trigg\br
Dirtlifter® 
p ower\frush 
does not turn Th\b b\blt is off or brok\bn
Turn pow\br OFF ( O ) and unplug unit 
from outl\bt. Follow instructions on pag\b 15
Th\b unit is in th\b upright position
brush\bs only rotat\b wh\bn unit is 
r\bclin\bd using th\b d\bt\bnt p\bdal
Circuit br\bak\br on machin\b may 
hav\b tripp\bd Turn th\b machin\b OFF ( O ) and 
unplug from outl\bt. Ch\bck to s\b\b if 
for\bign obj\bct is caught in brush roll. 
R\bmov\b obj\bct. Plug machin\b in to 
r\bs\bt circuit br\bak\br
c\beaner   
not picking 
up so\bution R\badyTools dial may b\b at wrong 
s\btting
s\bt R\badyTools dial to \bith\br Fl
OOR 
CleANiNG or TOOls s\btting 
Tank may not b\b s\bat\bd prop\brly Pick up both th\b 2-in-1 wat\br tank and 
formula tank and r\bs\bat th\bm so th\by 
fit snugly on th\b unit 
Tank may not b\b ass\bmbl\bd prop\brlyCh\bck to mak\b sur\b th\b "lip" of th\b 
nozzl\b is s\bcur\bly hook\bd into th\b 
groov\b on bottom of Tank (s\b\b pag\b 7)
solution or 2-in-1 wat\br tank is 
\bmptyCh\bck fluid l\bv\bls in h\bavy duty  
bladd\br and formula tank
2-in-1 wat\br tank has pick\bd up maximum 
dirty wat\br and r\bd float door has clos\bd. empty 2-in-1 wat\br tank. R\bfill h\bavy duty 
bladd\br with cl\ban hot tap wat\br and r\bplac\b. 
R\bd float "door" in th\b tank may 
hav\b clos\bd as a r\bsult of bumping 
an obj\bct or moving machin\b back 
and forth too quicklyTurn th\b machin\b OFF ( O ), allowing r\bd 
float door to r\bl\bas\b into th\b op\bn posi-
tion. Turn unit back ON ( 
i ) to continu\b 
cl\baning.  b\b sur\b your forward and back -
ward strok\bs ar\b don\b at a slow\br pac\b.
R\bd lint scr\b\bn in tank is dirtyR\bmov\b r\bd lint scr\b\bn, cl\ban and r\bplac\b.
Oth\br maint\bnanc\b or s\brvic\b not includ\bd in th\b manual should   
b\b p\brform\bd by an authoriz\bd s\brvic\b r\bpr\bs\bntativ\b.
Thank you for s\bl\bcting a  bissell product.
for any questions or concerns,  \fISSEll is happy to 
be of service.  contact us direct\by at 1-800-237-7691.
p\bease do 
not return 
this product 
t o   t h e   s t o r e .              
www. bissell.com
      800.237.769116
W
aRnInG
To reduce the risk of electric shock, turn power switch 
off and disconnect plug from electrical outlet before 
performing maintenance or troubleshooting checks.  
						

							Replacement Parts
These items are available for your BI\f\fELL Pro\beat 2X deep cleaner.  
Call 1-800-237-7691 or visit www.BI\f\fELL.com
Par T # ParT name ParT # ParT name
203-7017 Tank Assembly (complete) 
(Black)
203-6660 Tank Lid (Black)
203-6618Tank Bottom (Black)203-6675 Cap and Insert for   
Water Tank
203-6676 Formula Tank (includes   
Cap & Insert for Formula Tank)203-6677 Cap and Insert for   
Formula Tank
203-7649 Floor Nozzle with End Cap 
Assembly203-6679 Autoload Gasket (fits both 
Water and Formula Tank)
203-6845Float Door203-6680 Tank Filter (Lint Screen)
203-6682Cord Wrap (Blue Illusion) 203-6685 Clear End Cap w/Edge Brushes 
(2 pack, includes screws)
203-6686Brush Roll – 6 row (includes   
1 brush, axle, 2 swivel arms)203-6688 Small Brush Belt   
(non-cord side)
203-6804 Large Brush Belt (cord side)203-6689 Hose Secure Latch
203-6690Hose Rack Assembly   
(Top/Bottom Hose Rack, Screws)
*Not all parts are included with every model.
www.bissell.com
   
   800.237.769117 
						

							Accessories
These items are available for your BI\f\fELL Pro\beat 2X deep cleaner.  
Call 1-800-237-7691 or visit www.BI\f\fELL.com
www. bissell.com
   
   800.237.7691
Par
T # ParT name ParT # ParT name
203-6651 3” Tough Stain Tool
203-6652 Powered TurboBrush®   
Hand Tool
203-6653 4” Upholstery Tool203-6654 6” Stair Tool
203-6655Spraying Crevice Tool 203-5642 Bare Floor Tool with trial size 
bottle of Hard Floor Solutions 
formula
203-7412Deep Reach Pet Tool160-0057  Stain Trapper Tool
62E5-22X Deep Clean and Protect 
Formula with Scotchgard™ 
Protection 60 oz. 99K5-2 2X Pet Stain and Odor   
Formula with Scotchgard™ 
Protection 60 oz. 
89Q5-2 2X Allergen Cleansing   
Formula 60 oz. 78H6-3 2X Professional Deep Cleaning 
Formula with Scotchgard™ 
Protection 48 oz. 
56L92X Hard Floor Solutions Formula 
16 oz.4001 Stain PreTreat 22 oz.
18
*Not all parts are included with every model. 
						

							This warranty gives you specific legal rights, and you may also  
have other rights which may vary from state to state. If you need   
additional instruction regarding this warranty or have questions   
regarding what it may cover, please contact BISSELL Consumer   
Care by E-mail, telephone, or regular mail as described below.
limited  two- year WarrantySubject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon 
receipt of the product BISSELL will repair or replace (with new or 
remanufactured components or products), at BISSELL’s option, free   
of charge from the date of purchase by the original purchaser, for 
two years any defective or malfunctioning part.
See information below on "If your BISSELL product should   
require service".
This warranty applies to product used for personal, and not commercial 
or rental service. This warranty does not apply to fans or routine 
maintenance components such as filters, belts, or brushes. Damage or 
malfunction caused by negligence, abuse, neglect, unauthorized repair, 
or any other use not in accordance with the User's Guide is not covered. 
BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES 
OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S 
LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT. 
Some states do not allow the exclusion or limitation 
of incidental or consequential damages, so the 
above limitation or exclusion may not apply to you. 
*EX cEptIonS anD EX clUSIonS fRom  
tHE tERmS of tHE lImItED W aRRanty
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER 
WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES 
WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 
PURPOSE, ARE LIMITED TO THE THREE YEAR DURATION FROM THE   
DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on  how long an implied   
warranty last so the above limitation may not apply to you.
notE: p\bease keep your origina\b sa\bes \l 
receipt. It provides proof of date of purchase 
in the event of a warranty c\baim.
If your  \fISSEll product shou\bd 
require service:
Contact BISSELL Consumer Care to locate a BISSELL Authorized Service 
Center in your area. 
If you need information about repairs or replacement parts, or if you 
have questions about your warranty, contact BISSELL Consumer Care.
Website or E-mai\b:www.bissell.com
or  ca\b\b:bissell Consum\br Car\b
1-800-237-7691
Monday – Friday 8am - 10pm eT
saturday 9am - 8pm eT 
sunday 10am - 7pm eT
or Write:bissell Hom\bcar\b, inc.
PO box 3606
Grand Rapids, Mi 49501
ATTN: Consum\br Car\b
Warranty Service
www.bissell.com
      800.237.769119  
						

							©2013 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 160-3115  Rev 10/13
Visit our website at: www.BISSELL.com
Scotchgard is a trademark of 3M 
For information about r\bpairs or r\bplac\bm\bnt parts, or qu\bstions about your warranty:R\bgist\bring is quick, \basy and off\brs you b\bn\bfits ov\br th\b lif\btim\b of your product.  
You’ll receive:
Visit www.\fISSEll.com/registration now!
Visit the \fISSEll website: www.\fISSEll.com
Wh\bn contacting  bissell, hav\b mod\bl numb\br of cl\ban\br availabl\b.
Pl\bas\b r\bcord your Mod\bl Numb\br: __________________\1_
Pl\bas\b r\bcord your Purchas\b Dat\b:  __________________\1_
NOTE: Please keep your original sales r\Ieceipt. It provides proof of purchase 
date in the event of a warranty claim. \fee Warranty on page 19 for details.  
ca\b\b:
BI\f\fELL Consumer Care1-800-237-7691
Monday - Friday  8 am - 10 pm eT 
saturday  9 am - 8 pm eT 
sunday  10am - 7pm eT
Write:
BI\f\fELL \bomecare, Inc.
PO Box 3606
Grand Rapids  MI 49501
ATTN: Consumer Care
BISSELL Consumer Care Register your product today!
\fISSEll Rewards pointsAutomatically \barn points for   
discounts and fr\b\b shipping on 
futur\b purchas\bs.
f aster Servicesupplying your information now 
sav\bs you tim\b should you n\b\bd to 
contact us with qu\bstions r\bgarding 
your product.
product Support Reminders 
and  a\berts
W\b’ll contact you with any   
important product maint\bnanc\b 
r\bmind\brs and al\brts.
Specia\b  promotionsOptional: R\bgist\br your \bmail  
to r\bc\biv\b notic\b of off\brs,  
cont\bsts, cl\baning tips and mor\b!
We can’t wait to hear from you!
Rat\b this product and l\bt us (and millions  
of your clos\bst fri\bnds) know what you think! 
www.\fISSEll.com
20