Bissell 8930 M Manual

www.bissell.com 800.237.769111
Operations
Carpet cleaning continued
8. Remove the tank from the base of the 
machine by lifting up on the tank carry 
handle. carry like a bucket to a utility sink 
or outside where you will dispose of the 
dirty water.
8a.  unlatch the top of the tank from the   
bottom by lifting up on the tank latch   
located on the back of the tank.
8b.  Remove the top of the tank by lifting up on 
the handle. 
Note how the lip on the top tank 
separates from the groove in the 
bottom...

www.bissell.com 800.237.7691
Operations
12
Cleaning with attachments
Your PROheat 2X machine comes 
equipped with a hose and at least 
one attachment for cleaning stairs, 
upholstery, and more.
1. Important! if using to clean uphol-stery, check upholstery tags. 
a.  check manufacturer’s tag before clean-
ing. “W” or “Ws” on the tag means 
you can use your pRoheat 2X. if the 
tag is coded with an “X” or an “s” 
(with a diagonal stripe through it), or 
says “dry clean only”, do not proceed 
with any deep...

www.bissell.com 800.237.769113
Operations
 
8. Remove and rinse tools in clean, running 
water. dry and replace in the tool caddy.
9.  it is recommended that you suction clean 
water from a bowl to rinse out the hose. 
10.  before replacing lift end of hose and 
stretch out to ensure all water is cleared 
from hose.
11.  coil flex hose around the tool caddy.
12.  empty 2-in-1 water tank and rinse out,  
following the instructions on page 11.  
13.  Return Readyt ools dial to floor setting.
Deep reach...

www.bissell.com 800.237.7691
Operations
14
Stain removal
Do Not Delay! Attending to an  
accident soon after it occurs ensures 
the most optimal clean. Leaving it 
for an extended period of time may 
cause it to set and become  
permanent.
1. blot up liquids with an absorbent cloth or 
paper towels. White materials are recom-
mended because certain dyes may bleed 
and make the stain worse.
2.  gently scrape up any semi-solids with a 
spoon or spatula. do not use a knife or other 
utensil with sharp edges...

www.bissell.com 800.237.769115
Operations
Hard floor cleaning
(Select models only)
Your PROheat 2X model may have 
come with a hard floor attachment 
and 2X Hard Floor Solutions Formula. 
If not, these products are available 
for purchase by contacting the BISSELL 
Consumer Services department by 
phone or at the website. The hard floor 
tool provides effective cleaning for lino-
leum, vinyl, and tile floors. Caution: Do 
not use on unsealed hardwood floors.
1. Vacuum with a specialized dry vacuum 
or...

www.bissell.com 800.237.7691
Operations
16
Machine storage
Once your cleaning is complete, 
make sure the 2-in-1 water tank is 
emptied, rinsed out, and dried before 
the next use. The formula tank can 
remain filled and ready to go.
Note: Store cleaner in a protected, 
dry area. Since this product uses 
water, it must not be stored where 
there is a danger of freezing. 
Freezing will damage internal  
components and void the warranty.
Machine care
For best results, a few simple steps can 
assure your...

www.bissell.com 800.237.769117
Maintenance and care  
Machine care continued
5. before you place the cleaned 2-in-1 
water tank back onto the machine, 
remove the red solution filter cap (on the 
base of the machine).Remove the cap 
by inserting a coin or a flat head screw 
driver into the slot on the top. t urn coun-
ter clock wise and unscrew. set aside.
5a.  Remove the white filter by grasping 
the post and pulling up and out of 
the unit. Rinse the filter under cold 
water.
Note: Be careful not to...

www.bissell.com 800.237.7691
Maintenance and care  
18
Machine care continued
6.  the inside of the end caps by the brush 
rolls can be wiped out with a clean paper 
towel, or, if a more thorough cleaning is 
desired, the end caps can be taken off 
using a phillips head       screwdriver and 
rinsed clean. Replace after cleaning.
7.  any loose hair or debris can be pulled from 
the brush rolls and thrown away. for the 
most thorough clean before storage, follow 
directions on pages 18 & 19 for removal...

www.bissell.com 800.237.769119
Maintenance and care   
 
Brushes can be removed for cleaning 
or replacement as needed. 
1. follow small belt removal instructions on   
page 18.
2.  Remove brush rolls by pulling them off 
of the metal rods. Be careful not to 
lose the small washer at each 
end of the brush rolls.
3.  place cleaned or new brush rolls back 
onto the rods. make sure one washer is 
on each end of the rollers prior to sliding 
onto the rod. be sure to let the rod slide 
through the bushing to...

www.bissell.com 800.237.7691
Troubleshooting
www.bissell.com 800.237.769120Built-in heater ready light does not illuminate
Possible causes 
Remedies
1.  The heater switch is not turned ON ( I )  1.  Turn the heater switch ON ( I )
2.   The power switch is not turned ON ( I )  2.  Both switches must be ON ( I ) to activate the   
    heater ready light
Reduce Spray or No Spray
Possible causes  Remedies
1.  Water tank may be empty   1.  Fill heavy duty bladder with hot tap water
2.   Formula tank may be...