Bissell 82g7h Manual

							www.bissell.com 800.237.769111
Maintenance and care
1. Unplug the vacuum from electrical 
outlet.
2. The pre-motor filter protects the 
motor from dirt particles. It is 
located in the slide out tray under-
neath the dirt container. If the filter 
becomes dirty, pull out the tray, lift 
out the foam filter pad and clean it. 
NOTE: The pre-motor filter may be 
hand washed in cold water with 
mild detergent. Rinse well and air 
dry thoroughly before replacing. 
DO NOT PUT IN DISHWASHER. 
3. The post-motor filter assists in the 
filtration process to return clean air 
to the room. It is located behind the 
door on the side of the vacuum. If 
the filter becomes dirty, open the 
door, remove the filter and replace. 
NOTE: The post-motor filter is a 
white pleated filter.  This filter 
is not washable and must be 
replaced when it becomes dirty.
Cleaning pre-motor and replacing post-motor filter
Post-Motor   
Filter
Washable 
Pre-Motor   
Filter
WARNING:   Do not operate cleaner with 
damp or wet filters or without 
all filters in place.  
						

							www.bissell.com 800.237.7691
Maintenance and care
12
You should check your vacuum clean-
er’s rotating floor brush and drive belt 
regularly for wear or damage. You 
should also clean the brush and brush 
ends of strings, hair and carpet fibers. 
This type of debris can wrap around 
the brush and hamper its ability to 
effectively clean your carpet. Also 
remove any debris that has  
accumulated under the brush cover. 
1.  Unplug the vacuum from electrical outlet.
2.  Place handle in low position and turn the 
vacuum cleaner over so bottom side is 
facing up. 
3.  Lift tab 1 and release the three latches 
in order 2-4 as marked. Lift off the brush 
cover.  
4.  Grasp the rotating floor brush at both 
ends and lift.
5.  Clean strings, hair and other debris  
from the rotating floor brush, paying 
particular attention to brush ends.
6.  Clean strings, hair and other debris from 
the motor pulley and drive belt areas. 
7.  Check the drive belt carefully for wear, 
cuts or stressed areas.  
8.  Check air passageway for obstructions. 
Remove debris from this area.   
9.  Insert front edge of brush cover, rotate 
into place, and snap three latches.
Check rotating floor brush and drive belt
WARNING:   To reduce the risk of injury from 
moving parts, turn vacuum cleaner 
off and disconnect power plug from 
electrical outlet.
Motor 
Pulley
Air Passageway
3.
4.  
						

							www.bissell.com 800.237.769113
Maintenance and care
Replace drive belt
1. Unplug the vacuum from electrical outlet.
2.  With the rotating floor brush removed 
from the vacuum cleaner (Steps 1-4 of 
check rotating floor brush and drive 
belt on page 12), grasp the old drive 
belt and remove from the motor pulley. 
Discard the old drive belt. 
3.  Place the new drive belt over the motor 
pulley and loop other end over the   
rotating floor brush in the space between 
the bristles. 
NOTE: It is important that you use 
only genuine BISSELL replacement 
belts. Generic belts may not meet 
the exact specifications required 
to keep your vacuum operating 
at its peak performance. The use 
of unbranded belts could lead to 
early failure of the vacuum and 
could void your warranty. 
4.  Pull the rotating floor brush firmly into 
position, stretching the drive belt and 
place ends of the rotating floor brush 
down into the slots on sides. Alignment 
of brush ends in slots may be necessary 
to fully insert the brush.
5.  Turn the rotating floor brush by hand sev-
eral times. If properly installed, the drive 
belt will center itself on the rotating brush 
crown.
6.  Insert front edge of brush cover, rotate 
into place, and snap 3 latches.
Replace lightbulb
1. Unplug the vacuum from electrical outlet.
2.  Using a flat head screwdriver, pry the 
tab on the left and right side out and 
pull out to remove the lens. 
3.  Remove the bulb from the socket by  
grasping the bulb and pulling gently. 
Install the new bulb by pushing it gently 
into the socket until the bulb snaps into 
place. 
4.  Reposition the lens and snap it back  
into place.
Motor 
Pulley
Motor 
Pulley
3.
4.
2. 3.
4.  
						

							www.bissell.com 800.237.7691
Maintenance and care
14
Maintaining TurboBrush
The TurboBrush should be checked 
regularly for clogs or debris wrapping 
around the brush.
1. Unplug the vacuum from electrical  
outlet. 
2.  Remove TurboBrush tool from the end of 
hose.
3.  If a clog is present or debris is visible, 
unscrew the two screws on the back of the 
TurboBrush to remove the faceplate and 
clear any obstructions.
4.  To clean debris from the brush, remove the 
brush from the drive belt and clean debris.
5.  Reposition the drive belt on the brush.  
Place ends of brush in slots on sides as 
shown. Reposition faceplate and secure 
with two screws. 2.
4.  
						

							www.bissell.com 800.237.769115
Maintenance and care 
Clearing clogs
Low suction or poor pickup may be 
due to a clog in the vacuum cleaner. 
If you notice a change in the sound of 
the motor, check for clogs. 
1. Unplug the vacuum from electrical  
outlet.
2.  Empty dirt container.
3.  Check upper tank for build up or clogs.
4.  If you notice a clog in the upper tank, 
flip the separator plate down, remove 
the debris barrier, and remove the 
article causing the clog. Replace debris 
barrier and flip separator door back 
to its original position. (see section 
"Cleaning the Upper Tank" on page 
16).  
5.  Grasp the curved wand and separate 
it from the hose wand base. Check for 
a clog in the base, the wand or in the 
hose. 
NOTE: On select units that have 
the clean filter indicator, when the 
indicator reads black, there is a 
clog in the hose which is diminish-
ing suction power. Remove the 
clog in the hose to restore full suc-
tion power.
6. Remove the Twist ‘n Snap hose from the 
vacuum by turning to the right. Straighten 
the hose and unclog with a long, narrow 
object. 
7.  If you notice debris or dirt clogged in 
the connecting tube, remove it by  
pulling it out at the top and lifting the 
tube out. Clean the tube of any debris 
and clear any possible clog from the 
port to the pre-motor filter. Reattach tube 
by first installing the base and then push 
in the top of the tube. 
8.  If the clog persists, follow the  
instructions for checking the rotating 
floor brush and drive belt on page 12 
and inspect the air passageway for 
obstructions. 
2.
4.
6. 5.
Hose Wand 
Base
Connecting 
 
Tube Twist n' Snap 
Hose
Bottom   
Port  
						

							www.bissell.com 800.237.7691
Maintenance and care
www.bissell.com 800.237.769116
Cleaning the upper tank
1. Unplug the vacuum from electrical outlet. 
2.  Remove the dirt container as instructed in 
"Empty Dirt Container" on page 10.
3.  Flip separator plate down.
4.  Remove debris barrier by pulling straight 
down. Remove any dirt or debris on the 
debris barrier itself.
5.  Wipe out the inside of the upper tank and 
the separator plate with a damp cloth 
moistened with water or a mild cleaning 
solution. Allow upper tank to dry   
completely.
6.  Replace debris barrier and flip separator 
plate up; returning to original position.
7.  Replace the dirt container.
4.
6.
3.
Debris Barrier  
						

							www.bissell.com 800.237.769117
Troubleshooting
Vacuum cleaner won’t run
Possible causes Remedies
1. Vacuum cleaner is not plugged in  1. Check electrical plug
2.  Blown fuse/tripped breaker  2. Check/replace fuse or reset breaker
Vacuum cleaner or tools won’t pick up dirt
Possible causes  Remedies
1. Incorrect height adjustment  1. Adjust powerfoot to correct height 
2.   Hose not attached to suction opening  2.  Firmly push hose wand into the suction opening
3.   Twist ‘n Snap hose not securely attached  3.  Make sure Twist ‘n Snap hose is snapped into locked position
4  Crack or hole in hose  4. Check hose and replace if needed
5.  Broken or worn drive belt  5. Replace drive belt, see page 13
6.  Rotating floor brush bristles worn  6. Replace brush
7.   Rotating floor brush jammed   7.  Remove brush and clean debris from brush ends
8.   Clog in vacuum   8.  Clear clog, see page 15 
9.  Dirt container full  9. Empty dirt container
10.  Dirt container or upper tank not installed properly  10. Position correctly and lock in place
11.  Filters are dirty   11. Check and clean upper tank, pre-motor and post-motor filters
12.  TurboBrush is clogged or debris is wrapped  12. Maintaining TurboBrush, see page 14  
  around the brush roll
Vacuum cleaner is difficult to push
Possible causes  Remedies
1. Incorrect height adjustment  1. Adjust powerfoot to correct height setting
Visible dirt escaping from cleaner
Possible causes  Remedies
1. Dirt container full  1. Empty dirt container
2.  Filters missing or installed incorrectly  2. Check upper tank, pre-motor and post-motor filters for   
    correct  installation
3.  Dirt container installed incorrectly  3. Pull out and re-insert dirt container correctly
Other maintenance or service not included in the manual should be   
performed by an authorized service representative.
Thank you for selecting a BISSELL product.
Please  do  not  return  this  product  to  the  store.             
For any questions or concerns, BISSELL is happy to be of service.  Contact us directly at 1-800-237-7691.
WARNING:  To reduce the risk of electric shock, turn power OFF 
and disconnect plug from electrical outlet before 
performing maintenance or troubleshooting.  
						

							www.bissell.com 800.237.7691
Replacement parts - BISSELL vacuum
18
You may purchase parts from your retailer, by calling BISSELL Consumer Services or by  
visiting our website. Below is a list of common replacement parts. While not all of 
these parts may have come with your specific model, they are available for purcha\
se if 
desired.  Please note, all attachments may not store on board your vacuu\
m.
Item  Part No.  Part Name
1 32074  Style 7/9/10/12/14 Drive Belt (2-Pack)
2  203-1297  Headlight Bulb
3  203-1063  Crevice Tool
4  203-1228  Dusting Brush/Upholstery Tool
5  203-2302  TurboBrush, clear top with black brush roll
6  203-1068  Extension Wand 
7  203-2303  Curved Hose Wand
8  203-2304  Twist 'n Snap Vacuum Hose (clear)
9   203-2305  Wide Window Foot Brush Roll (gray)
10  3290  Style 7/8/14 Pre-Motor Foam Filter
11  3091  Style 8/14 Post-Motor Filter 
12  203-2431  Hose & Cord Wrap
13  203-2307  Cord Clip
14  203-2308  Hose Clip 
12345
678910
11121314  
						

							www.bissell.com 800.237.769119
Warranty - BISSELL Momentum® Cyclonic Vacuum 
This warranty gives you specific legal rights, and you may also have oth\
er rights which may vary from state to state. If you need additional instruction regarding this\
 warranty or have 
questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail, 
telephone, or regular mail as described below.
Limited three Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Homecare, Inc. will repair or replace (with new or remanufactur\
ed components or 
products), at BISSELL’s option, free of charge from the date of purchase by the original  
purchaser, for three years any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial o\
r rental service. This   
warranty does not apply to fans or routine maintenance components such a\
s filters, belts, or 
brushes. Damage or malfunction caused by negligence, abuse, neglect, una\
uthorized repair, or any 
other use not in accordance with the User's Guide is not covered.
 
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your 
area. 
If you need information about repairs or replacement parts, or if you have questions about 
your warranty, contact BISSELL Consumer Services.
Website or E-mail:  
www.bissell.com  
Use the “Customer Services” tab.
Or Call:  
BISSELL Consumer Services  
1-800-237-7691  
Monday - Friday 8 a.m. - 10 p.m. ET  
Saturday 9 a.m. - 8 p.m. ET 
Or Write:  
BISSELL Homecare, Inc.  
PO Box 3606  
Grand Rapids, MI 49501  
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL 
DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S 
LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
 
Some states do not allow the exclusion or limitation of incidental or co\
nsequential damages, so the 
above limitation or exclusion may not apply to you. 
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER 
ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION 
OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS 
FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE THREE YEAR DURATION FROM 
THE DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on  how long an implied warranty la\
st so the  
above limitation may not apply to you.  
						

							Registering is quick, easy and offers you benefits over the lifetime of \
your product.  
You’ll receive:
BISSELL Rewards Points
Automatically earn points for discounts and free shipping on future purchases.
Faster Service
Supplying your information now saves you time should you need to contact us with 
questions regarding your product.
Product Support Reminders and Alerts
We’ll contact you with any important product maintenance reminders and alerts.
Special Promotions
Optional: Register your email to receive notice of offers, contests, cle\
aning tips and more!
Visit www.bissell.com/registration now!
don't forget to register your product!
For information about repairs or replacement parts, or questions about your warranty, call:
BISSELL Consumer Services  1-800-237-7691
 
Monday - Friday  8 a.m. — 10 p.m. ET
Saturday    9 a.m. —   8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids  MI 49501
ATTN: Consumer Services
 
Or visit the BISSELL website -  www.bissell.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date:  ___________________
NOTE: Please keep your original sales receipt. It  
provides proof of purchase date in the event of a  
warranty claim. See Warranty on page 19 for details.  
BISSELL consumer services
www.bissell.com 800.237.769120
Registering is quick, easy and offers you benefits over the lifetime of \
your product.   
You’ll receive:
BISSELL Rewards Points
Automatically earn points for discounts and free shipping on future purchases.
Faster Service
Supplying your information now saves you time should you need to contact us with 
questions regarding your product.
Product Support Reminders and Alerts
We’ll contact you with any important product maintenance reminders and alerts.
Special Promotions
Optional: Register your email to receive notice of offers, contests, cle\
aning tips and more!
Visit www.bissell.com/registration now!
don't forget to register your product!
©2013 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in Korea
Part Number 160-3160
Rev 9/13
Visit our website at:
www.bissell.com