Bissell 3576 6 Manual

1.
USER’S GUIDE
3574/73G8/3576/20Q9 SERIES
Safety Instructions3
Product View4
Assembly Instructions5-6
Operation / Special Tools6-8
Maintenance8-12
Troubleshooting12-13
Warranty16
Replacement Parts14
Consumer Services15
CleanView
®
 II
BAGLESS
Earn BISSELL Rewards! 
Register your  
product today!
See details on   
page 15   

1.2
Thanks For Buying A BISSELL CleanView® II
We’re glad you purchased a BISSELL CleanView II Vacuum. Everything we 
know about floor care went into the design and construction of this complete,   
high-tech home vacuuming system.
Your BISSELL CleanView II is well made, and we back it with a limited  
comprehensive one-year warranty. We also stand behind it with a  
knowledgeable, dedicated Consumer Services Department, so, should you ever 
have a problem, you’ll receive fast, considerate assistance.
My...

1.3
  IMPORTAnT SAFETy InSTRUCTIOnS
When using an electrical appliance, basic 
precautions should be observed, including 
the following: 
READ ALL InSTRUCTIOnS  
BEFORE USInG y OUR  
UPRIGHT VACUUM. 
 
Always connect to a polarized outlet (left slot is 
wider than right). Unplug from outlet when not in 
use and before conducting maintenance. 
    
 WARnInG:
 To reduce 
the risk of fire, electric shock,   
or injury:
 ■  Do not  modify the polarized plug to fit a  
non-polarized outlet or extension cord....

1.4
 CAUTIOn:  Do not plug in your vacuum 
cleaner until  you are familiar 
with  all instructions  and  
operating procedures.
Power Switch
Carrying
Handle
Crevice Tool
Post-Motor 
Filter
Quick Reach
®
 
Handle Handle
Quick Release 
Cord Wrap
Handle 
Release  
Pedal
Powerfoot Stretch Hose 
Extension Wand
Power Cord
Furniture Protection Guard
Height 
Adjustment 
Knob
Upper Tank
Dirt Container
Lock ’n Seal™
 
Lever
Headlight
Combination 
Dusting Brush/ 
Upholstery Tool
Hose Wand
Hose Clip
Furniture...

1.5
How To Put It Together
Select Models Only
The only tool you’ll need to assemble your vacuum 
cleaner is a screwdriver.
Locate the vacuum Handle and remove the screw  
packet taped to the base of the Handle.
Stand the vacuum upright and slide the base of  
the Handle firmly into the grooves at the top of the  
vacuum body.
Check to be sure the Handle is fitted to the vacuum 
body. If there is a gap in front, continue to push firmly 
until the Handle is flush.
Insert the screw provided from the screw...

1.
Press the Handle Release Pedal with your foot to place 
your vacuum in one of three cleaning positions.
Upright- For storage and above floor cleaning with tools.
Normal Cleaning- Press Handle Release Pedal once. 
Use for most household floor cleaning tasks.
Low Cleaning- With the vacuum in normal cleaning 
position, press Handle Release Pedal again. Use for 
reaching under low furniture such as tables, chairs  
or beds.
  The Powerfoot/Rotating Floor Brush can be adjust-
ed to clean several floor...

1.
 Your BISSELL CleanView II is not only a pow-
erful carpet and rug vacuum cleaner, it’s also a 
versatile above floor vacuum cleaner when you 
select one of the special tools.
Raise Handle to Upright Position.
Grasp the Quick Reach Handle and lift Hose Wand to 
separate from suction intake opening.
Attach tools by firmly pushing onto Vacuum Hose or 
Extension Wand.
Combination Dusting Brush/Upholstery Tool:
Two types of cleaning tools are included in one attach-
ment: rotate for desired tool.
■ Use...

1.
To maintain maximum cleaning performance, the 
following maintenance steps must be performed:
Empty the Dirt Container when the dirt reaches the 
“Full” line on the side. 
Check the Inner and Outer Circular Filters and the  
Pre-Motor Filter at least once a month and clean or 
replace as needed.
Replace the Post-Motor Filter every three to six months.note: More frequent filter cleaning or 
replacing may be necessary if you are  
vacuuming new carpet, fine dust, or have 
allergy concerns. Follow the...

1.
Separate the Outer foam and Inner pleated Circular Filters. Wash each 
individually by hand in warm water. Mild detergent may be used if 
desired. Rinse well, then air dry thoroughly before putting them back 
together and replacing in Filter Cup.
The Filter Cup may be washed in warm water with a mild detergent. 
Make sure it is completely dry before reassembling with filters.
The Upper Tank and Louvers may also be wiped clean with a damp 
cloth. Reach underneath the Upper Tank and turn the rim of the...

1.
For standard models, remove the four screws as shown 
with a Phillips Head Screwdriver. Lift the Brush Cover off.
For wide cleaning path models, Lift tab 1 and release the 
three latches in order 2-4 as marked. Lift the Brush Cover off.
Grasp Rotating Floor Brush at both ends and lift.
Clean strings, hair and other debris from Rotating Floor 
Brush, paying particular attention to brush ends.
Clean strings, hair and other debris from Motor Pulley and 
Drive Belt areas.
Check Drive Belt carefully for...