Bissell 1697m Manual

							12
Cleaning bare floors
Tilt Handle
Back
Carrying
Bottom Front Edge of
Machine Base
Snap Together
Bare Floor 
Cleaning 
Tool
Handle Release
The Bare Floor Tool provides effective cleaning for
linoleum, vinyl, and tile floors. 
Caution: Do not use on hardwood floors.
1. Use only BISSELL Floor cleaning Formula.
2. Vacuum or sweep thoroughly to pick up loose debris and
pet hair.
3. Remove easily moved furniture from the room, (chairs,
tables, etc).
4. Plan your cleaning route to leave an exit path.
5. Plan activities to allow about 30 minutes for the floor to 
dry completely.
Attach the Bare Floor Tool
6. Step on the handle release to lay the machine handle down.
7. Remove the Tank-in-Tank™from the machine base.
8. Lift the machine base to expose the underside of the nozzle.
9. Attach Bare Floor Tool to nozzle with long tab to the right
side (ReadyTools
™side) of the nozzle.
10. First attach left side (short tab) catching tab over 
nozzle edge.
11. Gently bend long tab (right side) outward to easily snap
over edge of clear nozzle on left. 
						

							13
Machine Preparation
1 2. Set up machine following instructions in The Basics
section, pages 5-9. Be sure to thoroughly rinse out any
remaining cleaning solution to prevent slippery linoleum,
vinyl, and tile floors. Use BISSELL floor cleaning
chemical in the SmartMix
®tank.
13. Check ReadyTools™switch - it should be set on 
Floor Cleaning.
14. Choose the SmartMix
®setting to match the cleaning job.
15. Plug into a proper outlet and turn Power Switch ON. 
Bare Floor Cleaning Technique
17. Slowly move the machine nozzle with Bare Floor Tool 
forward and back over soiled surface one time while 
pressing the trigger. 
Caution: Do not over wet.
18. Repeat the motion without pressing the trigger using the 
Bare Floor Tool to squeegee and suction up the dirty water.
19. Repeat steps 1 and 2 backing along the exit path.
20. Allow about 30 minutes for the floor to dry completely.
21. When the cleaning job is complete refer to the
Maintenance/Putting it Awaysection, page 14, for
machine cleanup and storage instructions.
22. To remove Bare Floor Tool gently bend long tab (right 
side) outward and pull tool down away from nozzle. 
Rinse thoroughly, dry and store.
When filling bottle or 
storing unit, set
dial to:  
Keep plenty of genuine BISSELL
cleaning formulas on hand so
you can clean whenever it fits
your schedule. Always use genuineBISSELL deep cleaning formulas.
Non-BISSELL cleaning solutions
may harm the machine and void
the warranty. 
						

							1. Turn Power switch OFF.
2. Unplug power cord from the outlet and coil around
machine cord wrap.
3. Remove and rinse tools in clean, running water, dry and
replace in tool caddy.
4. Coil flex hose around storage brackets on tool caddy.
5. Remove Tank-in-Tank,
™dispose of dirty water. See The
Basics section, page 8.
6. Rinse out the Tank-in-Tank
™and replace on the machine.
7. Clean out the Flow Indicator Filter each time it is used to
insure best cleaning performance. Unscrew the Flow
Indicator Cap, lift out the red Rotor and white Filter. 
Rinse all three parts in tap water. Replace the Filter and
Rotor. Replace the Flow Indicator Cap; turn until snug, 
do not over-tighten.
8. To remove the Clear Nozzle for cleaning out remaining
dirt and carpet fibres, unscrew the two screws with a
Phillips        screwdriver. Rotate the Clear Nozzle up toward
the handle and lift out. Wipe machine base with a clean
damp cloth. Rinse nozzle in tap water and replace. Catch
the two tabs in the notches at the top, then rotate down
and replace the screws.
9. Wipe all exterior surfaces with a soft cloth.
10. Store cleaner upright in a protected, dry area.
14
Maintenance/Putting it away
CAUTION: 
POWERSTEAMER®PRO™
uses water and must not 
be stored where there 
is a danger of freezing.
Freezing will damage 
internal components and
void the warranty.
Cap
Rotor
Filter
O
NOF
F
Tip:
SmartMix® 
Bottle may be
stored with 
concentrate
ready for 
your next 
cleaning job.
Set
dial to:   
						

							Reduced spray or no spray.
Possible Causes Remedies
Bladder may be empty. Refill tank with hot tap water.
SmartMix
®Bottle may be empty. Fill with BISSELL chemical.
The filter may be clogged. Clean out filter, page 14.
Tanks may not be seated properly. Turn power OFF; remove and reseat tanks.
Pump may have lost prime. Turn power OFF; after 1 minute turn ON and 
depress trigger.
The Pump Belt may be broken. Turn the machine OFF and unplug from the outlet.
To check if a Pump Belt has broken, you will need
a flat head        screwdriver. Insert the blade end 
into the lower slot of the Belt Access door to release
the lower snap. If necessary, insert the blade end 
into the upper slot to release the upper snap. 
Examine for belt breakage. You should be able to
see the Pump Belt looped around the motor shaft.
If it is broken or missing, please refer to  
Part Numbers and Descriptionson page 17 
before calling Customer Service.
Complete installation instructions will accompany
the replacement belt.
15
Troubleshooting
WARNING:To reduce the risk of
fire, electric shock or
injury unplug from
outlet before servicing.
Insert
Screwdriver
Blade HereLift Here 
						

							16
Dirtlifter®PowerBrush does not turn.
Possible Causes Remedies
The Brush Belt or Pump Belt Turn the machine OFF and unplug from the 
may be broken. outlet. To check if a Brush Belt has broken,
you will need a flat head        screwdriver.
Insert the blade end into the lower slot of the
Belt Access door to release the lower snap. If 
necessary, insert the blade end into the upper
slot to release the upper snap. Examine for 
belt breakage. The Brush Belt should be 
visible, looped around the motor shaft. 
If it is broken or missing, please refer to 
Part Numbers and Descriptionson 
page 17 before calling Customer Service. 
Complete installation instructions will 
accompany the replacement belt.
Vacuum not picking up solution.
Possible Causes Remedies
ReadyTools™switch may be at the  Set ReadyTools™switch to either Tools or 
wrong setting for the cleaning job. PreTreat or Floor Cleaning.
Drain cap may be missing or not   Remove Tank-in-Tank,
™loosen and 
properly installed at back of  re-tighten Drain Cap.
Tank-in-Tank.
™
Tank-in-Tank™lid is not  Re-install lid; refer to The Basicssection.
properly installed.
Tank-in-Tank
™is not properly seated. Tank-in-Tank™ must be firmly seated to 
function; remove and reseat Tank-in-Tank.™
Poor tool position. Adjust angle; apply more downward pressure.
(Hand held attachments only).
Tank-in-Tank
™ has picked upEmpty Tank-in-Tank,™refer to 
maximum dirty water.The Basics section.
Troubleshooting - continued 
						

							17
Item Part No. Part Name
1* 010-9201 4” Small Area Tool
2* 603-0910 6” Stair Tool
3* 010-9148Spraying Crevice Tool
4* 010-1185 TurboBrush
™
5* 014-9131Bare Floor Tool
6* 014-9142PreTreat Wand
7* 015-9155 Tough Stain Brush
8 013-0212 Baffle
9 014-0325 Red Float
10 015-9040 Tank Assembly
11 010-6241 Tank Seal
12 014-2987 Tank Lid Assembly 
13 013-4435 Tank Handle
14 014-1782 Tank Drain Cap
15 010-1785 SmartMix
®Bottle
(Includes Cap)
16 010-1795 SmartMix
®Cap Assembly
17 010-1651 Flow Indicator Cap
18 010-6214 Flow Indicator O-Ring
19 010-7635 Flow Indicator Rotor
20 010-3510 Flow Indicator Filter
21 014-9860 Floor Nozzle Window
and Gasket
22 010-4052 Window Gasket
23 010-0620 Belt – Pump
24 010-0621 Belt – Brush
Part numbers and descriptions*
NOTE:  To order replacement parts, or to 
order parts not originally included in your 
POWERSTEAMER
®PRO™model, call
BISSELL Customer Service
1-800-263-2535
Monday - Friday
8:00 A.M. - 4:30 P.M. (E.S.T.)
BRUSH
SUCTION
1*
7*
8
2*
3*
4*5*
6*
10
11
12
14
15
2423
16
17
9
18
19
20
21
22
* Not all attachments are included with every model. Please turn to page 4 to see
what comes with your PowerSteamer®Pro™model.
13 
						

							18
About your warranty
One Year Warranty
BISSELL Ltd., or an Authorized BISSELL Service Centre will repair or
replace, free of charge, any part which is defective or malfunctioning
within 1 year of the purchase date, provided that it is used for personal
and not commercial or rental service.
PLEASE CALL, TOLL FREE, 1-800-263-2535 to obtain an
Authorized BISSELL Service Centre in your area.
Terms:
1.Return the unit and/or part with proof of purchase date, to your dealer,
your nearest BISSELL Authorized Service Centre, or return by mail to.
BISSELL Ltd.,
6934 Kinsmen Court,
Niagara Falls, Ontario, L2E 6S5
2.  Any defective or malfunctioning part will be repaired or replaced and
returned postage paid.
3.  This warranty does not cover belts, filters or light bulbs.
For your protection, you should always insure the unit and/or part
when shipping or mailing. BISSELL will reimburse you for the parcel
post, CanPar or UPS charge. Any charges for packaging or insurance
are your responsibility.
Tip: Attach your sales receipt to this User’s Guide for future reference.
BISSELL Customer Service
For information about repairs or replacement parts, or questions about your warranty, call:
BISSELL Customer Service
1-800-263-2535
Monday - Friday
8 A.M. — 4:30 P.M.  (E.S.T.)
Or write:
BISSELL Ltd.
Attn: Customer Service
Box 1003,
Niagara Falls, Ont., L2E 6W2
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date:  ___________________
NOTE:  Please keep your original sales receipt. It is your warranty.
It is suggested you staple your original receipt to the
front of this guide.
©1998 BISSELL Inc.
BISSELL Ltd.
Niagara Falls, Ont., L2E 6W2
All rights reserved. Printed in USA
Part Number 010-5857 
Visit our web site at:
http://www.bissell.com
WARNING:Use only
BISSELL cleaning formulas
in your POWERSTEAMER
®
. PRO.™Use of cleaningformulas which contain
lemon or pine oil may damage
this applianceand void
warranty. Chemical spot
cleaners or solvent-based
soil removers should not be
used. These products 
may react with the plastic
materials used in your 
POWERSTEAMER
®PRO™
causing cracking or pitting.