Bissell 1694 W Manual

							11
Step on the handle release to lay the machine handle down.
Remove the Tank-in Tank from the machine base.
Lift the machine base to expose the underside of the nozzle.
Attach Bare Floor Tool to nozzle with long tab to the right side
(ReadyTools side) of the nozzle.
First attach left side (short Tab) catching tab over nozzle edge.
Gently bend long tab (right side) outward to easily snap over
edge of clear nozzle on left.
Set up machine following instructions in The Basics on pages
6-9. Be sure to thoroughly rinse out any remaining Fiber
Cleansing Formula from the Tank-in-Tank bottle to prevent
slippery linoleum, vinyl, and tile floors.Use BISSELL Floor
Cleansing Formula in the Tank-in-Tank.
Check ReadyTools dial - it should be set on FLOOR CLEANING.
Plug into a proper outlet and turn Power Switch ON.
Slowly move the machine nozzle with Bare Floor Tool 
forward and back over soiled surface one time while 
pressing the trigger.Caution: Do not over wet.
Repeat the motion without pressing the trigger using the Bare
Floor Tool to squeegee and suction up the dirty water.
Repeat steps 1 and 2 backing along the exit path.
Allow about 30 minutes for the floor to dry completely.
When the cleaning job is complete refer to the
Maintenance/Storagesection on page 13.
To remove Bare Floor Tool gently bend long tab (right side) 
outward and pull tool down away from nozzle. Rinse 
thoroughly, dry and store.
6.
Machine Preparation
1.
2.
3.
Attach the Bare Floor Tool
1.
2.
3.
4.
5.
Bare Floor
Cleaning ToolSnap Together Bottom Front Edge of
Machine Base
Tilt 
Handle
Back
Handle Release
Carrying
Bare Floor Cleaning Technique
1.
2.
3.
4.
5.
6.
WARNING: To reduce the risk of fire,
electric shock or injury
unplug from outlet
before servicing. 
						

							Check manufacturer’s tag before cleaning. A "W" or "WS" on
the tag means you can use your PowerSteamer. If the tag is
coded with an "X" or "S" (with a diagonal strike through), or
says "Dry Clean Only," do not proceed. Do not use your
PowerSteamer on velvet or silk. If manufacturer’s tag is 
missing or not coded, check with your furniture dealer.
Check for colorfastness in an inconspicuous place.
If possible, check upholstery stuffing. Colored stuffing may
bleed through fabric when wet.
Plan activities to give upholstery time to dry.
Vacuum thoroughly to pick up loose debris and pet hair. Use a
vacuum with a brush attachment and a crevice tool to clean in
fabric folds and tufts.
Set up the machine following instructions in The Basics sec-
tion, pages 6-9.
Using the Measuring Cup provided, pour BISSELL Advanced
Deep Cleaning Formula into the Tank-in-Tank.
Set the ReadyTools Dial to TOOLS/PRETREAT.
12
How To Clean Upholstery and Small Areas
Ad
sdfddghg bv
h
cv
bb
j jkn hnbj jk
vh
gcghhjj  jhf
fhl kllgh
Important - Check Upholstery Tags
Machine Preparation
1.
2.
3.
Manufacturer’s
Ta g 
						

							13
Maintenance/Storage
Turn Power Switch OFF.
Unplug Power Cord from outlet and coil cord
around Power Cord Quick Release.
Remove and rinse tools, if used, in clean, running
water. Dry and replace.
Coil Flex Hose through storage brackets.
Remove Tank-in-Tank. Dispose of dirty water. See
The Basics section, page 8.
Rinse out Tank-in-Tank and reseat the tank unto
the machine.
Wipe all exterior surfaces with a soft cloth.
Store cleaner in a protected, dry area.
When carpet is dry, vacuum again to remove 
hair and fuzz that the PowerSteamer may 
have loosened.
NOTE: Turn off machine and unplug from
wall outlet.
Step on Handle Release pedal and recline Handle
on floor (see illustration).
Remove the Tank-in-Tank. Set aside (see illustration).
Remove the Belt Access Door located near the
ReadyTools Dial. Insert a flathead screwdriver into
the slot nearest the handle to gently pry off the
door (see illustration).
1.
3.
4.
2.
5.
6.
7.
8.
9.
CAUTION: PowerSteamer®uses water
and must not be stored
where there is a danger of
freezing. Freezing will 
damage internal components
and void the warranty.
Pump & Brush Belts Replacement
To Remove Broken Pump & Brush Belts
1.
2.
3.
Power Cord
Quick Release
Flex Hose
Storage Bracket
1
2
3 
						

							14
To Remove Broken Pump & Brush Belts-Continued
Turn the machine onto its side so the belt access area is
facing upward (see illustrations).
On the bottom of the machine, near the belt access area, is
a Red Retainer Plate that holds the black brush arm and
brush in place. Using a Phillips head screwdriver remove
the screw that holds the Red Retainer Plate in place. Set
Red Retainer Plate and Phillips head screw aside 
(see illustrations).
NOTE: For 1693 Model Series, remove stationary
brush (skip step 6 and 7).
Remove the black brush arm that holds the brush in place.
Set the black brush arm aside 
(see illustrations).
Remove the "toothed" Brush Belt from the Brush then from
the Red Pump Pulley. Set the "toothed" Brush Belt and
Brush aside.
Locate and remove the broken Pump Belt.4.
5
6.
7.
8.
54
6
7
8Red Retainer
Plate 
						

							15
To Install The Replacement Pump & Brush Belts
NOTE: For 1693 Model Series, skip steps 2 & 4.
With the unit still on its side, loop one end of the replacement
Pump Belt around the Red Pump 
Pulley and the other end around the silver motor shaft (see illustra-
tion). Do not twist the replacement Pump Belt.
Re-install the “toothed” Brush Belt first onto the Red Pump Pulley
and then onto the “toothed” end of the Brush (see illustrations).
Re-install the Brush into the base of the unit.
Place the black brush arm onto the Brush and slide black brush
arm into original position (see illustrations).
1.
2.
3.
4.
21
3
4 
						

							16
To Install The Replacement Pump & Brush Belts-Continued
Re-install the Red Retainer Plate and Phillips head screw
(see illustration).
Using your finger, gently spin the replacement Pump Belt 
on the silver motor shaft (see illustration). If assembled 
correctly, the replacement Pump Belt should rotate freely
around the silver motor shaft and drive pulley without
obstruction. The Brush should also rotate freely when the
silver motor shaft is turned.
Turn the machine right side up. Replace the Tank-in-Tank
and Belt Access Door (see illustration).
Assembly is now complete.
If you have any questions, or if you have any trouble
installing your replacement Pump Belt, please call BISSELL
Consumer Services 
at 1-800-237-7691.
Or visit the BISSELL website
:www.bissell.com
5.
6.
7.
5
6
7Red Retainer
Plate
Belt Access
Door 
						

							17
WARNING: To reduce the risk of fire,
electric shock, or injury,
unplug machine from
outlet before servicing.
Reduced spray or no spray.
Possible Causes Remedies
Bladder may be empty Refill tank with hot tap water.
The lint screen may be clogged Clean out lint screen page 8.
Tank-in-Tank may not be seated properly Turn power off; remove and reseat tank.
Pump may have lost prime. Turn power OFF; after 1 minute, turn 
ON and depress Spray Release trigger.
The Pump Belt may be broken. Turn power OFF and unplug machine 
from outlet. To check if a Pump Belt 
has broken, you will need a flathead
screwdriver. Insert the blade
end into the lower slot of the Belt 
Access Door to release the lower snap.
If necessary, insert the blade end into 
the upper slot to release the upper 
snap. Examine for belt breakage. You 
should be able to see the Pump Belt 
looped around the motor shaft. If it is 
broken or missing, please refer to the 
Part numbers and descriptions on 
page 19 before calling BISSELL 
Consumer Services. Complete 
installation instructions will accompany
the replacement belt.
DirtLifter PowerBrush* does not turn.
Possible Causes Remedies
The Brush Belt or Pump Belt Turn power OFF and unplug machine
may be broken  from outlet. To check if a Brush Belt
has broken, you will need a flathead 
screwdriver. Insert the blade 
end into the lower slot of the Belt
Access Door to release the lower snap.
If necessary, insert the blade end into 
the upper slot to release the upper
snap. Examine for belt breakage. If 
broken, refer to pages 13-16.
Troubleshooting
Lift Here
Insert Screwdriver
Blade Here
*On select models only 
						

							18
Troubleshooting-continued
PowerSteamer not picking up solution.
Possible Causes Remedies
ReadyTools Dial may be at the Set ReadyTools Dial to either FLOOR
wrong setting for cleaning job. CLEANING or TOOLS/PRETREAT.
Nozzle Window may not be Make sure the two tabs on the back of
properly attached. the Nozzle Window are inserted
through the mating slots in the main 
housing. Reinstall if necessary.
Tank-in-Tank lid is not  Reinstall lid; refer to The Basics 
properly installed. section, page 7.
Tank-in-Tank is not properly seated. Tank-in-Tank must be firmly seated to 
function. Remove and reseat Tank-in Tank.
Tank-in-Tank has picked up the maximum Empty tank and refill; refer to
amount of dirty water. Basics section, page 8.
Poor tool position. Readjust angle; apply more downward
(Handheld attachments only.) pressure.
Thank you for selecting a BISSELL product.
If you should happen to need assistance during assembly or operation, call: 1-800-237-7691
Please do not return this 
product to the store.
For information about repairs or replacement parts, or questions about your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. — 9 p.m. EST
Saturday 9 a.m. — 5 p.m. EST
Or write:
BISSELL INC
PO Box 3606
Grand Rapids  MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It is your warranty.
BISSELL Consumer Services
©2002 BISSELL Inc
Grand Rapids, Michigan
All rights reserved. Printed in USA.
Part Number 310-5800
Rev 3/02
Visit our website at:
www.bissell.com
Scotchgard a trademark of 3M  
						

							19
Part Numbers And Descriptions*
*Not all parts included with every model
Item Part No. Part Name
1 603-7818 Handle Assembly with Screw
2 215-9155 Tough Stain Brush
3 015-9043 Tank Assembly Complete
4 015-4439 Tank Lid Assembly
5 015-9041 Tank Bottom
6 213-0213 Baffle with Red Float
7 210-4052 Window Gasket
8 015-0628 Replacement Pump Belt (with instructions)
9 015-0621 Replacement Brush Belt (with instructions)
10 015-3500 Lint Screen
11 213-3010 Measuring Cup
12 214-9131 Bare Floor Tool
13 0710 48 oz. BISSELL Fiber Cleansing Formula with Scotchgard
™
14 0400 22 oz. BISSELL Tough Stain PreCleaner
15 0480 32 oz. BISSELL Floor Cleansing Formula
P
U
S
H
13
TOUGHSTAINPRECLEANER™PenetratesandLoosensToughStains&EmbeddedDirtbeforeDeepCleaning
14
Floor Cleansing Formula
FOR DEEP 
CLEANING MACHINES™
32 FL.OZ.(946 mL)CAUTION:MAY BE IRRITATING TO THE EYES.
                                                 READ BACK PANEL CAREFULLYSafely Deep Cleans and
Revitalizes No-Wax FloorsDIRTANDSTAINSREMOVESDEEPDOWN
®
15 12
119 8 7
64 3 2
1
10 5 
						

							20
About Your Warranty
This warranty gives you specific legal rights, and you may also have other rights which
may vary from state to state. If you need additional instruction regarding this warranty
or have questions regarding what it may cover, please contact BISSELL Consumer
Services by E-mail, telephone, or regular mail as described below.
LimitedOneYear Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the
product BISSELL Homecare, Inc. will repair or replace (with new or remanufactured
components or products), at BISSELL’s option, free of charge from the date of 
purchase by the original purchaser, for one year any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This
warranty does not apply to fans or routine maintenance components such as filters, belts, or
brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or
any other use not in accordance with the User's Guide is not covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your
area.
If you need information about repairs or replacement parts, or if you have questions about
your warranty, contact 
BISSELL Consumer Services.
Website or E-mail:
www.bissell.com
Use the “Customer Services” tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 9 p.m. EST
Saturday 9 a.m. - 5 p.m. EST 
Or write:
BISSELL Homecare Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services 
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE
ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE
PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITEDWARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN.
ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO 
THE TWO YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.