Bisell Powertrak 2400 1491E User Manual

POWERFORCE 300
™ 
POWERTRAK 2400
™ 
User GUide
1491 SER\fES  

 
Thanks for buying a BISSELL vacuum 
We’re \blad you purchased a B\fSSELL vacuum. Everythin\b we  
know about floor care went into the desi\bn and construction of 
this complete, hi\bh-tech home cleanin\b system.
Your B\fSSELL vacuum is well made, and we back it with a limited 
two-year \buarantee. We also stand behind it with a knowled\beable, 
dedicated Consumer Care department, so, should you ever have a 
problem, you’ll receive fast, considerate assistance.
My \breat-\brandfather invented the floor...

imPorTANT sAfeTy iNsTrUcTioNs
reAd  All iNs TrUcTioNs   
\fefore  UsiNG yoUr VA cUUm.  
When using an electrical appliance, basic precautions should be 
observed, including the following: 
WArNiNG
t o reduce the risk of fire, electric   
shock, or injury:
»    Do not leave appliance when plu\b\bed in.
»    Unplu\b from electrical socket when not in use and 
before servicin\b.
»    Do not allow to be used as a toy.
»    Not intended for use by persons (includin\b children) 
with reduced physical, sensory...

AB1
12
13
14
15
17
16
18
19
20
21
23
24
25
22
1
2
3
4
5
6
7
8
9
1011
2.4.
1.
2.
3. 4.
6.
3.
1.
5.
3.
4.
2.
B2
28
2726
www. bissell.com
   
   4
2930
Product View Assembly (handle)
Assembly (hose) 

C1C3C2
D1
D2
D4
D3
D5
2.3.
2.
4. 4.
8.
3.
3.
2. 5.
6.
3. 4. 5.6.
      www.
bissell.com5
Handle Position 
Cleaning Inner Cyclone Filter
Cleaning   
Post Motor Filter
Replacing   
Drive Belt  Clearing ClogsChecking Brush & Drive Belt
Height 
 
Adjustment Empty Dirt Tank 

Before using your vacuum, make sure that the dirt 
tank is in the locked position and that both filters 
(pre-motor and post-motor) are in place. Do not 
operate your vacuum without these filters.
The rotating floor brush continues to rotate while 
tools are in use. To reduce the risk of injury from 
moving parts, always move the cleaner with the 
carrying handle at the back of the cleaner. Always place vacuum 
cleaner on floor with handle in upright position when using tools. 
Never place your fingers...

C Operations
Power switch
The Power sw\ftch \fs located on the left s\fde 
of the vacuum. Push the rocker sw\ftch “ON” 
(i) to vacuum, and “OFF” (O) when clean\fng 
\fs complete. 
c1-Handle position
Press the handle release pedal w\fth your 
foot to place your vacuum \fnto one of three 
clean\fng pos\ft\fons.
1. Upright– For storage and a\bove floor   
clean\fng w\fth tools.
2.  Normal\fcleaning – Press handle release   
household floor clean\fng tasks.
3.  \bow\fcleaning –W\fth the vacuum \fn   
normal...

Power cable storage
When you have f\fn\fshed us\fng your bissell 
vacuum, return \ft to the upr\fght pos\ft\fon and 
store the power ca\ble.
1. Turn vacuum cleaner off.
2. Unplug power ca\ble \by grasp\fng the   
polar\fzed plug (NOT the ca\ble) and   
d\fsconnect from socket.
3. Wrap power ca\ble around ca\ble wraps 
located on the \back of the vacuum.
4. Cl\fp molded plug to power ca\ble to 
secure.
c3-empty dirt tank
The d\frt tank needs to \be empt\fed when 
the d\frt reaches the “Full” l\fne on the...

d2-replacing the   
post-motor filter
Use only a genu\fne  bissell replacement 
post-motor f\flter \fn your  bissell vacuum.
1. Unplug the cleaner from electr\fcal socket.
2. To access the post-motor f\flter, remove 
the f\flter tray located \below the  easy empty 
d\frt tank.  
3. When the f\flter \becomes d\frty, remove the 
f\flter from the \bottom of the tray and clean 
or replace the f\flter. (T\fp: fl\fp the f\flter tray 
over to access the f\flter). 
No Te\b  your vacuum comes with both a 
regular...

ProblemPossible causes remedies
Vacuum   
cleaner won’t   
turn on Power ca\ble not plugged \fn
Check electr\fcal plug
blown fuse/tr\fpped \breaker Check/replace fuse or reset \breaker
Vacuum   
cleaner won’t   
pick up dirt incorrect he\fght adjustment
Adjust powerfoot to correct he\fght sett\fng
Hose not attached to suct\fon 
open\fng 
Grasp the hose wand and f\frmly 
 
push \fnto the hose wand \base
Crack or hole \fn hose Check hose and replace \ff needed
broken or worn dr\fve \belt Replace dr\fve...