Bisell BISSELL ProHeat 2X Revolution Carpet Cleaner 18588 User Manual

							www.BISSELL.com11
Cleaning with the Bare Floor Tool
21
Turn off and unplug your machine. 
Attach the bare floor tool to the 
foot’s bottom by lining the tool 
to the edge of the nozzle. Rotate 
down until it clicks into place. 
Follow filling instructions on page 
8 using the Wash & Shine Hard 
Floor Cleaner formula and switch 
cleaning mode to Express Clean. When finished, 
unplug the machine 
and remove the 
bare floor tool by 
rotating the tool up 
to unhook from the 
nozzle. Rinse and let 
dry before storing. 
Plug into a properly 
earthed outlet and turn 
the machine on. Clean by 
pressing the spray trigger 
for 1 wet pass forward, 1 
wet pass back, and then 
release the spray trigger 
and make 1 dry pass 
forward, 1 dry pass back.
3
WARNING
WARNING: To reduce the risk of fire and electric shock when cleaning a hard floor, the 
BISSELL Bare Floor Tool must be used, and is only to be used with BISSELL Wash & Shine 
Hard Floor Cleaner formula intended for use with this appliance.
(select models only)
Empty Dirty Water Tank
To remove dirty water 
tank, press down on the 
coloured tank handle.
Tilt the tank slightly toward 
you. Grab the handle and 
tank with both hands.
Pull dirty water tank up 
and away to remove. 
(continue to step 4)
2
WARNING
To reduce the risk of fire, electric shock or injury, turn power OFF and disconnect plug from 
electrical outlet before performing maintenance or troubleshooting.
13 
						

							www.BISSELL.com12
Empty Dirty Water Tank (continued)
Clean the red filter 
below the dirty 
tank by wiping off 
any remaining dirt 
or debris.
Quick Empty: 
 
Pull the rubber tab   
(located at the corner 
of the top of the tank) 
and tilt to pour. When 
closing the rubber tab, 
make sure all edges are 
sealed tight.
Final Rinse & Clean: 
Unscrew ring at bottom 
of tank by turning 
counterclockwise. 
Gently remove the float 
stack, rinse and clean. 
Once clean, return float 
stack into the tank by 
lining up the arrows 
to point at each other. 
With the arrows aligned, 
the float stack will lock 
into place. Return the 
ring and twist clockwise 
to lock. Water may leak 
if the ring is not fully 
tightened.
 
Did You Know? 
The Float Stack 
is what prevents 
your dirty   
tank from 
overflowing. 
4
6
5
Return Dirty Tank: 
Angle the tank 
and insert bottom 
first. Then tilt the 
tank toward the 
machine and push 
the top in until it 
clicks into place.
1
Maintenance: Cleaning Machine After Use
First, fill the clean water 
tank with warm tap water 
and then empty it all to 
rinse. Then fill again with 
warm tap water and return 
the tank to the machine. 
Twist cap back on tightly. To flush and rinse machine: 
Turn the machine on and 
press the spray trigger for 
15 seconds while making 
back and forth passes on a 
section of carpet. Release 
the spray trigger and suck 
up the water.
See pages 11-12 to clean the 
water that was just sucked 
up from the dirty tank.
Empty the clean water tank 
and let dry before storing.
Wipe your machine’s 
 
exterior with a soft cloth.
WARNING
To reduce the risk of electric shock, turn power switch off and disconnect plug from 
electrical outlet before performing maintenance or troubleshooting checks. 
						

							Maintenance: Cleaning the Nozzle
21
34
If pet hair or debris 
become clogged in 
the nozzle, it can 
be cleaned out of 
the nozzle with the 
nozzle clean out tool.
Turn off and unplug 
the machine from 
the earthed outlet.Remove the nozzle from the foot by 
flipping the accessory hose door open, 
then lifting the accessory hose door and 
nozzle up and away from the foot.
Return the nozzle back   
onto the foot of the   
machine by lining up the   
three hooks on the   
nozzle to the bottom of   
the foot. (see arrows for location) 
Rotate the nozzle up and click into place. 
Close the accessory hose door.
Hold the nozzle and insert the nozzle clean 
out tool into the thin slot on the bottom of 
the nozzle that touches the floor. Move the 
nozzle clean out tool up and down, back 
and forth to clean.
www.
BISSELL.com13
Maintenance: Cleaning the Brush Rolls
213
Turn off and unplug   
the machine from the 
earthed outlet. Lay the machine down 
 
on its back or side. Use the comb to brush 
 
out the debris or hair from 
the brush rolls.
WARNING
To reduce the risk of electric shock, turn power switch off and disconnect plug from 
electrical outlet before performing maintenance or troubleshooting checks. 
						

							Replace smaller 
toothed belt by 
wrapping around 
the small metal 
toothed pulley, 
and the gear at 
the end of the 
rear-most brush.
Return belt/brush 
access plate to the 
end of the brush rolls. 
It will “click” in place 
when screws align. 
Use a screwdriver to 
secure the plate with 
the three screws.
Replace and secure the 
brush roll cover, making 
sure brush rolls are 
aligned.
NOTE: It is important 
the brush rolls align on 
both ends of the foot.
Maintenance: Replacing Belts & Brush Roll
6
8
7
9
If the belt is 
broken, gently 
remove it from 
the machine.
To replace the 
large belt, place it 
over the red area 
of the large pulley 
near the front of 
the machine.4
5
www. BISSELL.com14
Remove the brush 
cover by lifting it up, 
then lift the small 
belt to remove. The 
brush rolls can be 
gently removed and 
replaced with new 
brush rolls. (Skip to 
step 7 for small belt 
replacement.)
Remove clean 
water tank and 
make sure the dirty 
water tank is empty. 
Press the recline 
pedal and lay the 
machine on its side. 
Remove 3 screws 
on the belt/brush 
access plate using a 
Philips screwdriver. 
Remove the plate 
to expose the belt.
Make sure to press the recline pedal   
and lay the machine on its back. Use   
a flathead screwdriver to help lift the   
belt access door and remove. If the 
belt is not broken, skip to step 8.
NOTE:  Force must be used to lift the belt access door. There is a small belt and end cap 
on the other end of the brush rolls. That belt needs to wrap around the tooth end of the 
brush rolls and the end cap needs to be secure before re-assembling the machine.
2
3
1
What you will need: 1 Phillips screwdriver & 1 flathead screwdriver
Large Wheel Belt 
Replacement
Brush Roll & Small 
Belt Replacement
Stretch the belt towards the back of the 
machine with your thumb and transfer it 
onto the metal axle. Snap the belt access 
door back into place. 
						

							ProblemPossible causes Remedies
Reduced 
spray OR  
no spray
Clean water tank may be emptyRefill tank
Clean water tank may not be   
seated completely Turn power OFF. Remove and 
 
reseat tank
Pump may have lost prime in 
hose cleaning mode Hold end of hose below water level 
in tank to prime
Loss of   
suction   
power Tanks may not be seated properly
Pick up both tanks and reseat them 
so they fit properly on the unit 
Dirty tank has picked up   
maximum amount of dirty water 
and has reached full line Empty dirty tank 
Clean water tank is empty Check fluid levels in the clean water 
tank. Refill the tank if it is empty
Rubber tab on dirty water tank is 
not sealed tight Check the rubber tab on the dirty 
water tank and press firmly on all 
edges to secure it tightly (see step 
 
4 on page 12 for detail)
Accessory hose door may not be 
closed tightly in place Check the accessory hose door 
 
and make sure it is closed tightly by 
pushing down to lock into place.
Nozzle may be clogged from pet 
hair or debris Use the nozzle clean out tool 
 
and follow steps on page 13 for 
“Cleaning Nozzle”
Troubleshooting
Helpful Cleaning Tips
WARNING
To reduce the risk of electric shock, turn power switch off and disconnect plug from 
electrical outlet before performing maintenance or troubleshooting checks.
››    Clean on a day with low humidity to help 
carpets dry faster.
While Cleaning
››  Turn on any available ceiling fans and 
make sure the room is well ventilated to 
help the airstream in your home.
››   Additional dry strokes will aid in faster 
drying of carpet. The two exceptions are 
when using Express Clean Mode or when 
using DeepClean + Antibacterial formula. 
With these exceptions, the directions need 
to be followed exactly.
After Cleaning
››   Use a portable fan directed towards 
the surface of the carpet and/or a 
dehumidifier to aid in drying carpet.
››   Adjust your heat up a few degrees in the 
winter and use your air conditioning for 
dryer air in the summer.
››   On warm dry days, simply opening the 
windows can be an eco-friendly option to 
assist in drying carpet.
››   When the carpet feels dry to the touch, 
return furniture that was removed. To be 
sure to avoid staining, place wax paper or 
aluminum foil under the legs. Wait at least 
another three hours before removing wax 
paper or foil.
For more helpful tips 
and videos, check out 
BISSELL.com
www. BISSELL.com15 
						

							©2016 BISSELL Homecare, Inc.
Grand Rapids, Michigan  USA
All rights reserved. Printed in China
Part Number 160-8817  Rev 01/16 RevA
Visit our website at: www.BISSELL.com
Scotchgard is a trademark of 3M
16If your BISSELL product should 
require service or to claim under 
our Limited Six-Year Guarantee, 
please contact us as follows:
 
Website or Email: 
www.BISSELL.com
[email protected]
Call or write: 
Telephone: 0344-888-6644
BISSELL Homecare (Overseas) Inc.
Ground Floor
226 Berwick Avenue
Slough
Berkshire, SL1 4QT
United Kingdom This Guarantee only applies outside of the USA and Canada. It is 
provided by BISSELL International Trading Company BV (“BISSELL”).
This Guarantee is provided by BISSELL.  It gives you specific rights.   
It is offered as an additional benefit to your rights under law. You   
also have other rights under law which may vary from country 
to country. You can find out about your legal rights and remedies 
by contacting your local consumer advice service. Nothing in this 
Guarantee will replace or lessen any of your legal rights or remedies.  
If you need additional instruction regarding this Guarantee or have 
questions regarding what it may cover, please contact BISSELL 
Consumer Care or contact your local distributor. 
This Guarantee is given to the original purchaser of the product from 
new and is not transferable. You must be able to evidence the date   
of purchase in order to claim under this Guarantee.
Limited Six-Year Guarantee
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, 
BISSELL will for six years from the date of purchase by the 
original purchaser repair or replace (with new or remanufactured 
components or products), at BISSELL’s option, free of charge, any 
defective or malfunctioning part or product.
BISSELL recommends that the original packaging and evidence   
of the date of purchase be kept for the duration of the Guarantee 
period in case the need arises within the period to claim on the 
Guarantee. Keeping the original packaging will assist with any 
necessary re-packaging and transportation but is not a   
condition of the Guarantee.
If your product is replaced by BISSELL under this Guarantee, the new 
item will benefit from the remainder of the term of this Guarantee 
(calculated from the date of the original purchase). The period of 
this Guarantee shall not be extended whether or not your product 
is repaired or replaced.
*EXCEPTIONS AND EXCLUSIONS FROM 
THE TERMS OF THE GUARANTEE
This Guarantee applies to products used for personal domestic use and 
not commercial or hire purposes.  Consumable components such as 
filters, belts and mop pads, which must be replaced or serviced by the 
user from time to time, are not covered by this Guarantee.  
This Guarantee does not apply to any defect arising from fair wear 
and tear. Damage or malfunction caused by the user or any third 
party whether as a result of accident, negligence, abuse, neglect, or 
any other use not in accordance with the User Guide is not covered 
by this Guarantee. 
An unauthorised repair (or attempted repair) will void this Guarantee 
whether or not damage has been caused by that repair/attempt.
Removing or tampering with the Product Rating Label on the   
product or rendering it illegible will void this Guarantee. 
SAVE AS SET OUT BELOW BISSELL AND ITS DISTRIBUTORS ARE NOT 
LIABLE FOR ANY LOSS OR DAMAGE THAT IS NOT FORESEEABLE 
OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY 
NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT INCLUDING 
WITHOUT LIMITATION LOSS OF PROFIT, LOSS OF BUSINESS, BUSINESS 
INTERRUPTION, LOSS OF OPPORTUNITY, DISTRESS, INCONVENIENCE OR 
DISAPPOINTMENT.  SAVE AS SET OUT BELOW BISSELL’S LIABILITY WILL 
NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
BISSELL DOES NOT EXCLUDE OR LIMIT IN ANY WAY ITS LIABILITY FOR 
(A) DEATH OR PERSONAL INJURY CAUSED BY OUR NEGLIGENCE OR THE 
NEGLIGENCE OF OUR EMPLOYEES, AGENTS OR SUBCONTRACTORS; (B) 
FRAUD OR FRAUDULENT MISREPRESENTATION; (C) OR FOR ANY OTHER 
MATTER WHICH CANNOT BE EXCLUDED OR LIMITED UNDER LAW.
Guarantee
Service
Spares are available for purchase.   
To purchase visit www.4bissell.co.uk.
Visit us online at:  
BISSELL.com
When contacting BISSELL, have model 
number of cleaner available.
Model Number:  ______________________
Purchase Date:   ______________________
NOTE: Please keep your original sales 
receipt. It provides proof of purchase 
date in the event of a warranty claim.  
Febreze® is a trademark of The Proctor & Gamble Company, 
Cincinnati, Ohio used under license by BISSELL Homecare, Inc.