BenQ W1070 Users Manual

  41
  Using the projector
Note that the menu items are available when the projector detects at least one valid signal. If there is no 
equipment connected to the projector or no signal detected, limited menu items are accessible.
System Setup 
: Basic
Language
Splash Screen BenQ/Black/Blue
Projector Position Front/Front Ceiling/Rear/Rear Ceiling
Auto OffDisable/5 min/10 min/15 min/20 min/25 min/
30 min
Sleep TimerDisable/30 min/60 min/90 min/120 min/150 
min/180 min
Menu SettingsMenu Display Time5...

42 Using the projector  
Picture menu
FunctionDescription
Preset Mode
Pre-defined picture modes are provided so you can optimize your projector 
picture set-up to suit your program type. See Selecting a preset mode on 
page 30 for details.
User Mode 
ManagementSelects a preset mode that most suits your need for the picture quality and 
further fine-tune the picture based on the selections listed below. See Setting 
the User 1/User 2/User 3 mode on page 30 for details.
BrightnessAdjusts the brightness of...

  43
  Using the projector
Audio Setup menu
Display menu
FunctionDescription
Mute
See Muting the sound on page 35 for details.
Vo l u m eSee Adjusting the sound level on page 35 for details.
Pow e r  O n / O f f  R i n g  
To n eSee Turning off the Power On/Off Ring Tone on page 35 for details.
FunctionDescription
Aspect Ratio
There are several options to set the picture’s aspect ratio depending on your 
input source. See Selecting the aspect ratio on page 36 for details.
Key s t o n eCorrects any...

44 Using the projector  
System Setup : Basic menu
3D
3D Mode
This projector features a 3D function which enables you to enjoy the 3D 
movies, videos, and sporting events in a more realistic way by presenting the 
depth of the images. You need to wear a pair of 3D glasses to view the 3D 
images.
When the 3D Mode function is enabled:
• The brightness level of the projected image will decrease.
•  The Preset Mode cannot be adjusted.
• The Keystone can only be adjusted within limited degrees.
3D Sync...

  45
  Using the projector
System Setup : Advanced menu
FunctionDescription
Lamp Settings
Reset Lamp Timer
Once the lamp is renewed, select Reset to return the lamp timer to 0. See 
Resetting the lamp timer on page 51 for details.
Equivalent Lamp Hour
Shows the lamp hour information. See Getting to know the lamp hour on 
page 48 for details.
HDMI Settings
HDMI Format
Selects an input source type for the HDMI signal. You can also manually select 
the source type. The different source types carry different...

46 Using the projector  
Information menu
This menu shows you the current operating status of the projector.
Some picture adjustments are available only when certain input sources are in use. Unavailable adjustments 
are not shown on the screen.
Reset All Settings
Returns all settings to the factory preset values.
The following settings will still remain: Keystone, Language, Projector 
Position, High Altitude Mode, Password, Key Lock, and ISF.
ISF
The ISF calibration menu is password protected and only...

  47
  Using the projector
Additional information
Care of the projector
Your projector needs little maintenance. The only thing you have to do on a regular basis is keep the lens 
clean. Never remove any parts of the projector except the lamp. Contact your dealer or local customer 
service center if the projector fails to operate as expected.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface. Before you attempt to clean the lens, 
turn the projector off, unplug the power...

48 Using the projector  
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by 
the built-in timer.
See Setting Lamp Power as Economic or SmartEco below for more information on Economic mode.
To obtain the lamp hour information:
1. Press MENU/EXIT and then press  /  until the System Setup : Advanced menu is highlighted.
2. Press   to highlight Lamp Settings and press MODE/ENTER. The Lamp Settings page...

  49
  Using the projector
Timing of replacing the lamp
When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, 
please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector 
and in some instances the lamp may explode. Go to http://lamp.BenQ.com for a replacement lamp.
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. Turn 
the power off and let the projector cool for 45...

50 Using the projector  
2. Loosen the screw that secures the lamp cover on the side of 
the projector until the lamp cover loosens.
3. Remove the lamp cover from the projector.
•  Do not turn the power on with the lamp cover removed.
•  Do not insert your fingers between the lamp and the projector. 
The sharp edges inside the projector may cause injuries.
4. Loosen the screw that secures the lamp.
5. Lift the handle so that it stands up.
6. Use the handle to slowly pull the lamp out of the projector.
•...