BenQ Projector SX930 User Manual

							  41
  Using the projector
EnglishUsing the test pattern
The projector is able to display the grid test pattern. It helps you adjust 
the image size and focus on checking that the projected image is free 
from distortion.
To display the test pattern: 
1. Press MENU/EXIT to open the OSD menu and press  /  to 
highlight the System Setup: Basic menu.
2. Press  to highlight Test Pattern and press  /  to select On. 
						

							42 Using the projector  
EnglishUsing the teaching templates
The projector provides several preset patterns for various teaching purposes. To activate the pattern:
1. Press MENU/EXIT to open the OSD menu and press  /  to highlight the Display menu.
2. Press  to highlight Teaching Template and press MODE/ENTER.
3. Press  /  to highlight Blackboard or Whiteboard.
4. Press  /  to select the desired pattern and press MODE/ENTER.
Te a c h i n g  Te m p l a t eWhiteboardBlackboard
Letter Formation
Wo r k s h e e t
Coordinate Chart 
						

							  43
  Using the projector
EnglishSetting the lamp mode
This projector provides two lamp modes for different purposes:
You can perform one of the following methods to choose a lamp mode according to your preference.
Using the remote control:
1. Press Lamp Mode on your remote control, the lamp mode page is displayed.
2. Press   to highlight your preferred lamp mode and press MODE/ENTER.
Using the OSD menu:
1. Press MENU/EXIT and then press  /  until the System Setup: Advanced menu is highlighted.
2. Press   to highlight Lamp Settings and press MODE/ENTER. 
3. Press   to highlight Lamp Mode and press MODE/ENTER.
4. Press   to highlight your preferred lamp mode and press MODE/ENTER.
A slight variation in the picture brightness and colors may be observed during the very short time of 
switching lamp modes.
Lamp modeUser benefitSuitable environment
Normal
(The lamp is used in normal mode)• Delivering bright and clear images
• Suitable for high-ambient-light environments 
• Allowing continuous and non-stop operation under 
critical situationsLarge, well lit meeting rooms 
or auditoriums
Economic
(The lamp is used in economic mode)• Extending the lamp life
• Allowing continuous and non-stop operation under 
critical situationsSmall-mid boardrooms 
						

							44 Using the projector  
EnglishControlling the projector through a Wired 
LAN environment
Wired LAN allows you to manage the projector from a computer using a web browser when the 
computer and the projector are properly connected to the same local area network.
Configuring the Wired LAN
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end 
to the RJ45 port.
When connecting the RJ45 cable, avoid coiling and intertwining the cable as it may cause signal noise or 
interruption.
2. Press MENU/EXIT and then press  /  until the System Setup: Advanced menu is highlighted.
3. Press  to highlight Network Settings and press MODE/ENTER. The Network Settings page 
is displayed.
4. Press  to highlight Wired LAN and press MODE/ENTER. The Wired LAN page is displayed.
5. Press  to highlight DHCP and press  /  to select On.
6. Press  to highlight Apply and press MODE/ENTER.
7. Go back to System Setup: Advanced > Network Settings page.
8. Press  to highlight AMX Device Discovery and press  /  to select On or Off. When AMX 
Device Discovery is On, the projector can be detected by AMX controller.
9. Please wait for around 15 - 20 seconds, and then re-enter the Wired LAN page.
10. The IP Address, Subnet Mask, Default Gateway, and DNS Server settings will be displayed. 
Note down the IP address displayed in the IP Address row.
If the IP Address still does not display, contact your ITS administrator.
If you are in a non-DHCP environment:
1. Repeat steps 1-4 above.
2. Press  to highlight DHCP and press  /  to select Off.
3. Contact your ITS administrator for information on the IP Address, Subnet Mask, Default 
Gateway, and DNS Server settings.
4. Press   to select the item you want to modify and press MODE/ENTER.
5. Press  /  to move the cursor and then press  /  to enter the value.
6. To save the setting, press MODE/ENTER. If you do not want to save the setting, press MENU/
EXIT.
7. Press MENU/EXIT to return to Network Settings page, press   to highlight AMX Device 
Discovery and press  /  to select On or Off.
8. Press MENU/EXIT to exit the menu. 
						

							  45
  Using the projector
EnglishControlling the projector re motely through a web browser
Once you have the correct IP address for the projecto r and the projector is on or in standby mode, you 
can use any computer that is on the same local area network to control the projector.
1. Enter the address of the projector in the address bar of your browser and click Go.
2. The remote network operation page opens. This pa ge allows you to operate the projector as if you 
were using the remote control or control panel on the projector.
• Menu • Auto PC See Remote control on page 11  for details.
• Blank • Input
• ( ) •  ( )
• ( ) • ( )
• OK
Activates the selected
 On-Screen Display 
(OSD) menu item.
To switch input source, click on your desired signal.
The source list varies according to the conn ectors available on the projector. Video 
stands for the Video signal.
i
ii
iii 
						

							46 Using the projector  
EnglishThe tools page allows you to manage the projector, configure the LAN control settings and secure access 
of remote network operation on this projector.
i.You can name the projector, keep track of its location and the person in charge of it.
ii. You can adjust the LAN Control Settings.
iii. Once set, access to the remote network operation on this projector has been password-
protected.
iv. Once set, access to the tools page has been password-protected.
After making the adjustments, press the Send button and the data will be saved in the projector.
v. Press Exit to go back to the remote network operation page.
Please pay attention to the limitation of input length (including space and other punctuation keys) in the 
list blow:
Category Item Input LengthMaximum Number of 
Characters
Crestron ControlIP Address 15
IP ID 4
Port 5
ProjectorProjector Name 22
Location 22
Assigned To 22
Network ConfigurationDHCP (Enabled) (N/A)
IP Address 15
Subnet Mask 15
Default Gateway 15
DNS Server 15
User PasswordEnabled (N/A)
New Password 15
Confirm 15
Admin PasswordEnabled (N/A)
New Password 15
Confirm 15
i
iv
iii
ii
v 
						

							  47
  Using the projector
EnglishThe info page displays the information and status of this projector.
For more information, visit http://www.crestron.com & www.crestron.com/getroomview.
Press Exit to go 
back to the 
remote network 
operation page. 
						

							48 Using the projector  
EnglishOperating in a high altitude environment
We recommend that you activate High Altitude when your environment is higher than 1500 meters 
(around 4920 feet) above sea level, or whenever the projector will be used for extended periods of time 
(>10 hours) without shutdown.
To activate High Altitude:
1. Press MENU/EXIT and then press  /  until the System Setup: Advanced menu is highlighted.
2. Press   to highlight High Altitude.
3. Press /  to select On. A confirmation message is displayed.
4. Highlight Ye s and press MODE/ENTER.
Operation under High Altitude may cause a higher decibel operating noise level because of increased fan 
speed necessary to improve overall system cooling and performance.
If you use this projector under other extreme conditions excluding the above, it may display auto shut-down 
symptoms, which is designed to protect your projector from over-heating. In cases like this, you should 
switch to High Altitude to solve these symptoms. However, this is not to state that this projector can 
operate under any and all harsh or extreme conditions. 
						

							  49
  Using the projector
EnglishTurning the projector off
To turn the projector off, press POWER ( ) on the projector or 
OFF   on the remote control and a warning message appears. 
Press POWER/OFF ( ) again.
•  The Power indicator light flashes orange and the fans run for 
about two minutes to cool the lamp. The projector will not 
respond to any commands until the cooling process is complete.
After turning off the projector, do NOT unplug the projector until 
the cooling process is complete and the fans stop running. 
Interrupting the cooling process in any way may cause overheating 
and result in damage to the projector.
•  Then, the Power indicator light is a steady orange once the 
cooling process has finished and fans stop.
•  If the projector will not be used for an extended period, unplug 
the power cable from the power outlet.
•  To protect the lamp, the projector will not respond to any 
commands during the cooling process.
•  Actual lamp life may vary due to different environmental conditions and usage.
•  If you attempt to re-start the projector shortly after shutdown, the fans may run for a few minutes to 
cool down. Press   Power/ON again to start the projector after the fans stop and the Power indicator 
light turns orange.
II
II
II
II 
						

							50 Using the projector  
EnglishOn-Screen Display (OSD) menus
On-Screen Display (OSD) structure
Please note that the on-screen display (OSD) menus vary according to the signal type selected.
Main menuSub-menuOptions
Picture
Picture Mode Bright/Presentation/sRGB/Cinema/(3D)/User 1/User 2
Reference Mode Bright/Presentation/sRGB/Cinema/User 1/User 2
Brightness 0~50~100
Contrast 0~50~100
Color 0~50~100
Tint 0~50~100
Sharpness 0–15
Advanced...Black Level 0 IRE/7.5 IRE
Noise Reduction 0-31
Color Temperature Cool/Normal/Warm/Lamp Native
Color Temperature 
Fine TuningRed Gain 0–200
Green Gain 0–200
Blue Gain 0–200
Red Offset 0–511
Green Offset 0–511
Blue Offset 0–511
3D Color 
ManagementPrimary Color Red/Green/Blue/Cyan/Magenta/Yellow
Hue 0–100
Saturation 0–100
Gain 0–100
Gamma Selection 1.6/1.8/2.0/2.2/2.4/2.5/2.6/2.8/BenQ
Brilliant Color On/Off
Rename User Mode User 1/User 2
Reset Picture Settings Current/All