BenQ Projector SU931 User Manual

  41
  Using the projector
EnglishUsing the test pattern
The projector is able to display the grid test pattern. It helps you adjust 
the image size and focus on checking that the projected image is free 
from distortion.
To display the test pattern: 
1. Press MENU/EXIT to open the OSD menu and press  /  to 
highlight the System Setup: Basic menu.
2. Press  to highlight Test Pattern and press  /  to select On. 

42 Using the projector  
EnglishUsing the teaching templates
The projector provides several preset patterns for various teaching purposes. To activate the pattern:
1. Press MENU/EXIT to open the OSD menu and press  /  to highlight the Display menu.
2. Press  to highlight Teaching Template and press MODE/ENTER.
3. Press  /  to highlight Blackboard or Whiteboard.
4. Press  /  to select the desired pattern and press MODE/ENTER.
Te a c h i n g  Te m p l a t eWhiteboardBlackboard
Letter Formation
Wo r k s h e...

  43
  Using the projector
EnglishSetting the lamp mode
This projector provides two lamp modes for different purposes:
You can perform one of the following methods to choose a lamp mode according to your preference.
Using the remote control:
1. Press Lamp Mode on your remote control, the lamp mode page is displayed.
2. Press   to highlight your preferred lamp mode and press MODE/ENTER.
Using the OSD menu:
1. Press MENU/EXIT and then press  /  until the System Setup: Advanced menu is highlighted.
2. Press...

44 Using the projector  
EnglishControlling the projector through a Wired 
LAN environment
Wired LAN allows you to manage the projector from a computer using a web browser when the 
computer and the projector are properly connected to the same local area network.
Configuring the Wired LAN
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end 
to the RJ45 port.
When connecting the RJ45 cable, avoid coiling and intertwining...

  45
  Using the projector
EnglishControlling the projector re motely through a web browser
Once you have the correct IP address for the projecto r and the projector is on or in standby mode, you 
can use any computer that is on the same local area network to control the projector.
1. Enter the address of the projector in the address bar of your browser and click Go.
2. The remote network operation page opens. This pa ge allows you to operate the projector as if you 
were using the remote control or...

46 Using the projector  
EnglishThe tools page allows you to manage the projector, configure the LAN control settings and secure access 
of remote network operation on this projector.
i.You can name the projector, keep track of its location and the person in charge of it.
ii. You can adjust the LAN Control Settings.
iii. Once set, access to the remote network operation on this projector has been password-
protected.
iv. Once set, access to the tools page has been password-protected.
After making the...

  47
  Using the projector
EnglishThe info page displays the information and status of this projector.
For more information, visit http://www.crestron.com & www.crestron.com/getroomview.
Press Exit to go 
back to the 
remote network 
operation page. 

48 Using the projector  
EnglishOperating in a high altitude environment
We recommend that you activate High Altitude when your environment is higher than 1500 meters 
(around 4920 feet) above sea level, or whenever the projector will be used for extended periods of time 
(>10 hours) without shutdown.
To activate High Altitude:
1. Press MENU/EXIT and then press  /  until the System Setup: Advanced menu is highlighted.
2. Press   to highlight High Altitude.
3. Press /  to select On. A confirmation message...

  49
  Using the projector
EnglishTurning the projector off
To turn the projector off, press POWER ( ) on the projector or 
OFF   on the remote control and a warning message appears. 
Press POWER/OFF ( ) again.
•  The Power indicator light flashes orange and the fans run for 
about two minutes to cool the lamp. The projector will not 
respond to any commands until the cooling process is complete.
After turning off the projector, do NOT unplug the projector until 
the cooling process is complete and the...

50 Using the projector  
EnglishOn-Screen Display (OSD) menus
On-Screen Display (OSD) structure
Please note that the on-screen display (OSD) menus vary according to the signal type selected.
Main menuSub-menuOptions
Picture
Picture Mode Bright/Presentation/sRGB/Cinema/(3D)/User 1/User 2
Reference Mode Bright/Presentation/sRGB/Cinema/User 1/User 2
Brightness 0~50~100
Contrast 0~50~100
Color 0~50~100
Tint 0~50~100
Sharpness 0–15
Advanced...Black Level 0 IRE/7.5 IRE
Noise Reduction 0-31
Color Temperature...