BenQ Projector MX528E User Manual

Operation 31
Securing the projector
Using a security cable lock
The projector has to be installed in a safe place to prevent theft. Otherwise, purchase 
a lock, such as the Kensington lock, to secure the projector. You can locate a 
Kensington lock slot on the rear side of the projector. See item 16 on page 10 for 
details.
A Kensington security cable lock is usually a combination of key(s) and the lock. Refer 
to the locks documentation for finding out how to use it.
Utilizing the password function
For...

Operation
32
If you forget the password
If the password function is activated, you will be 
asked to enter the six-digit password every time 
you turn on the projector. If you enter the wrong 
password, the password error message as pictured 
to the right displays lasting for three seconds, and 
the message INPUT PASSWORD follows. You 
can retry by entering another six-digit password, or 
if you did not record the password in this manual, and you absolutely do not 
remember it, you can use the password...

Operation 33 6. You have successfully assigned a new 
password to the projector. Remember to 
enter the new password next time the 
projector is started.
7. To leave the OSD menu, press MENU/EXIT.
Disabling the password function
To disable password protection, go back to the SYSTEM SETUP: Advanced > 
Security Settings > Change Security menu after opening the OSD menu system. 
The message INPUT PASSWORD displays. Enter the current password. 
• If the password is correct, the OSD menu returns to the...

Operation
34• The input signal type effects the options available for the Picture Mode. 
See Selecting a picture mode on page 36 for details.
For best display picture results, you should select and use an input signal 
which outputs at this resolution. Any other resolutions will be scaled by 
the projector depending upon the aspect ratio setting, which may cause 
some image distortion or loss of picture clarity. See Selecting the aspect 
ratio on page 35 for details.
Changing Color Space
In the unlikely...

Operation 35 5. To navigate the picture, press MODE/ENTER to switch to the paning mode 
and press the directional arrows ( ,  ,  ,  ) to navigate the picture.
6. Use the directional arrows ( ,  ,  ,  ) on the projector or remote control 
to navigate the picture.
7. To reduce size of the picture, press MODE/ENTER to switch back to the 
zoom in/out functionality, and press AUTO to restore the picture to its original 
size. You can also press   repeatedly until it is restored to the original size.
The...

Operation
364.16:9: Scales an image so that it is displayed in the center of the screen with a 
16:9 aspect ratio. This is most suitable for images which are already in a 16:9 
aspect, like high definition TV, as it displays them without aspect alteration.
5.16:10: Scales an image so that it is displayed in the center of the screen with a 
16:10 aspect ratio. This is most suitable for images which are already in a 16:10 
aspect, like high definition TV, as it displays them with out aspect alteration....

Operation 37 This function is only available when User 1 or User 2 mode is selected up in 
the Picture Mode sub-menu item.
5. Press  /  to select a picture mode that is closest to your need.
6. Press  to select a sub-menu item to be changed and adjust the value with  /
. See Fine-tuning the image quality in user modes below for details.
7. When all settings have been done, highlight Save Settings and press MODE/
ENTER to store the settings.
8. The confirmation message Setting Saved displays.
Using Wall...

Operation
38This feature utilizes a new color-processing algorithm and system level enhancements 
to enable higher brightness while providing truer, more vibrant colors in picture. It 
enables a greater than 50% brightness increase in mid-tone images, which are 
common in video and natural scenes, so the projector reproduces images in realistic 
and true colors. If you prefer images with that quality, select On. If you don’t need it, 
select Off.
When Off is selected, the Color Temperature function is...

Operation 39 The Color Management provides six sets (RGBCMY) of colors to be adjusted. When 
you select each color, you can independently adjust its range and saturation according 
to your preference.
If you have purchased a test disc which contains various color test patterns and can be 
used to test the color presentation on monitors, TVs, projectors, etc. You can project 
any image from the disc on the screen and enter the 3D Color Management menu 
to make adjustments.
To adjust the settings:
1. Go to...

Operation
40
Setting the presentation timer
The presentation timer can indicate the 
presentation time on the screen to help you 
achieve better time management when giving 
presentations. Follow these steps to utilize this 
function:
1. Press Timer Set up on the remote control 
or go to the SYSTEM SETUP: Basic > 
Presentation Timer menu and press 
MODE/ENTER to display the 
Presentation Timer page.
2. Highlight Timer Period and decide the timer period by pressing  / . The 
length of time can be set from...