BenQ Projector MS502 User Manual

							Introduction 11
Remote control
1. POWER
Toggles the projector between standby 
mode and on.
2.  Freeze
Freezes the projected image.
3. Left
4. Smart Eco
Displays the lamp mode selection bar.
5. ECO BLANK
Used to hide the screen picture.
6. Digital Zoom (+, -)
Magnifies or reduces the projected picture 
size.
7. Volume +/-
Adjusts the sound level.
8. MENU/EXIT
Turns on the On-Screen Display (OSD) 
menu. Goes back to previous OSD menu, 
exits and saves menu settings. 9. Keystone/Arrow keys ( / Up, 
/Down)
Manually corrects distorted images 
resulting from an angled projection.
10. AUTO
Automatically determines the best 
picture timings for the displayed image.
11. Right
When the On-Screen Display (OSD) 
menu is activated, the #3, #9, and #11 
keys are used as directional arrows to 
select the desired menu items and to 
make adjustments.
12. SOURCE
Displays the source selection bar.
13. MODE/ENTER
Selects an available picture setup mode.
Activates the selected On-Screen 
Display (OSD) menu item.
14. Timer On
Activates or displays an on-screen timer 
based on your own timer setting.
15. Timer Set up
Enters presentation timer setting 
directly.
16. PAGE UP/PAGE DOWN
Operate your display software program 
(on a connected PC) which responds to 
page up/down commands (like Microsoft 
PowerPoint).
1
3
7
8
9
10
11
12
14
15
16
13
96
2
4
5 
						

							Introduction 12
Remote control effective range
Infra-Red (IR) remote control sensor is located on the front of the projector. The remote 
control must be held at an angle within 30 degrees perpendicular to the projectors IR 
remote control sensor to function correctly. The distance between the remote control 
and the sensor should not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote control and the IR sensor on 
the projector that might obstruct the infra-red beam.
Replacing the remote control battery
1. Pull out the battery holder.
Please follow the illustrated instructions. Push and hold the locking 
arm while pulling out the battery holder.
2. Insert the new battery in the holder. Note the 
positive polarity should face outward.
3. Push the holder into the remote control.
•  Avoid excessive heat and humidity.
•  There may be battery damage if the battery is incorrectly 
replaced.
•  Replace only with the same or equivalent type recommended by 
the battery manufacturer.
•  Dispose of the used battery according to the battery 
manufacturers instructions.
•  Never throw a battery into a fire. There may be danger of an explosion.
•  If the battery is dead or if you will not be using the remote control for a long time, remove the battery to 
prevent damage to the remote control from possible battery leakage.
•  Operating the projector from the front
App
ro
x.
 +
1
5º 
						

							Positioning your projector 13
Positioning your projector
Choosing a location
Your projector is designed to be installed in one of four possible installation locations: 
Your room layout or personal preference will dictate which installation location you select. 
Take into consideration the size and position of your screen, the location of a suitable 
power outlet, as well as the location and distance between the projector and the rest of 
your equipment.1. Front Table
Select this location with the projector 
placed on the table in front of the screen. 
This is the most common way to position 
the projector for quick setup and 
portability.
2. Front Ceiling
Select this location with the projector 
suspended upside-down from the ceiling in 
front of the screen.
Purchase the BenQ Projector Ceiling 
Mount Kit from your dealer to mount your 
projector on the ceiling.
Set Front Ceiling in the SYSTEM 
SETUP: Basic > Projector Position 
menu after you turn the projector on.3. Rear Ceiling
Select this location with the projector 
suspended upside-down from the ceiling 
behind the screen.
Note that a special rear projection screen 
and the BenQ Projector Ceiling Mount Kit 
are required for this installation location.
Set Rear Ceiling in the SYSTEM 
SETUP: Basic > Projector Position 
menu after you turn the projector on.
4. Rear Table
Select this location with the projector 
placed on the table behind the screen.
Note that a special rear projection screen 
is required.
Set Rear Table in the SYSTEM SETUP: 
Basic > Projector Position menu after 
you turn the projector on. 
						

							Positioning your projector 14
Obtaining a preferred projected image size
The distance from the projector lens to the screen, the zoom setting, and the video format 
each factors in the projected image size.
For example, if you are using an 120-inch screen, the recommended projection distance is 
4755 mm and the vertical offset is 183 mm.
If your measured projection distance is 6.0 m (6000 mm), the closest match in the 
Distance from screen (mm) column is 5943 mm. Looking across this row shows that a 
150 (about 3.8 m) screen is required.
Projection dimensions 
Refer to Dimensions on page 52 for the center of lens dimensions of this projector 
before calculating the appropriate position.
All measurements are approximate and may vary from the actual sizes. 
BenQ recommends that if you intend to permanently install the projector, you should physically test the 
projection size and distance using the actual projector in situ before you permanently install it, so as to make 
allowance for this projectors optical characteristics. This will help you determine the exact mounting position 
so that it best suits your installation location.
Screen sizeDistance from screen (mm)
Vertical offset (mm)DiagonalW 
(mm)H 
(mm)
Min 
length
Average
Max 
length
Inchmm(max. 
zoom)(min. 
zoom)
30 762 610 457 1132 1189 1245 46
40 1016 813 610 1509 1585 1660 61
50 1270 1016 762 1887 1981 2075 76
60 1524 1219 914 2264 2377 2491 91
80 2032 1626 1219 3019 3170 3321 122
100 2540 2032 1524 3774 3962 4151 152
120 3048 2438 1829 4528 4755 4981 183
150 3810 3048 2286 5660 5943 6226 229
200 5080 4064 3048 7547 7925 8302 305
220 5588 4470 3353 8302 8717 9132 335
250 6350 5080 3810 9434 9906 10377 381
300 7620 6096 4572 11321 11887 12453 457
Maximum zoom Minimum zoom
Projection distanceCenter of lens Screen
Vertical offset 
						

							Connection 15
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
•  In the connections shown below, some cables may not be included with the projector (see Shipping 
contents on page 8). They are commercially available from electronics stores.
•  The connection illustrations below are for reference only. The rear connecting jacks available on the 
projector vary with each projector model.
•  Many notebooks do not turn on their external video ports when connected to a projector. Usually a key 
combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled CRT/
LCD or a function key with a monitor symbol on the notebook. Press FN and the labeled function key 
simultaneously. Refer to your notebooks documentation to find your notebooks key combination.
•  The D-Sub output only works when an appropriate D-Sub input is made to the COMPUTER 1 jack.
1. VGA cable
2. VGA to DVI-A cable
3. USB cable
4. Component Video to VGA (D-Sub) 
adapter cable5. S-Video cable
6. Video cable
7. Audio cable
7
774121
6
3
5
Notebook or desktop computer
Speakers
orA/V device
Monitor
(DVI) (VGA)
or 
						

							Connection
16
•  If you wish to use this connection method when  the projector is in standby mode, make sure the 
Monitor Out function is turned on in the SYSTEM SETUP: Advanced  menu. See Standby Settings 
on page 41  for details.
Connecting video source devices
You need only connect the projector to a video source device using just one of the 
connecting methods, however each provides a  different level of video quality. The method 
you choose will most likely depend upon the availability of matching terminals on both the 
projector and the video source device as described below:
Connecting audio
The projector has built-in mono speaker(s)  which are designed to provide basic audio 
functionality accompanying data presentation s for business purposes only. They are not 
designed for, nor intended for stereo audio reproduction use as might be expected in 
home theater or home cinema applications. An y stereo audio input (if provided), is mixed 
into a common mono audio output  through the projector speakers.
The built-in speaker will be muted when the  AUDIO OUT jack is connected.
•  The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See 
Connecting audio on page 16  for details.
•  If the selected video image is not displayed after the  projector is turned on and the correct video source 
has been selected, check that the video source device  is turned on and operating correctly. Also check 
that the signal cables have  been connected correctly.
Te r m i n a l  n a m eTerminal appearancePicture quality
Component Video
Better
S-VideoGood
VideoNormal 
						

							Operation 17
Operation
Starting up the projector
1. Plug the power cord into the projector and into a 
power outlet. Turn on the power outlet switch 
(where fitted). Check that the POWER indicator 
light on the projector lights orange after power 
has been applied.
Please use the original accessories (e.g. power cord) only with the 
device to avoid possible dangers such as electric shock and fire.
2. Press  POWER to start the projector. As soon as the lamp lights up, a Pow e r  
On Tone will be heard. The POWER indicator light flashes green and stays 
green when the projector is on.
The start up procedure takes about 30 seconds. In the later stage of start up, a 
startup logo is projected.
(If necessary) Rotate the focus ring to adjust the image clearness.
To turn off the ring tone, see Turning off the Power On/Off Ring Tone on page 33 
for details.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds 
before energizing the lamp.
3. If the projector is activated for the first 
time, select your OSD language following 
the on-screen instructions.
4. If you are prompted for a password, press 
the arrow keys to enter a six-digit 
password. See Utilizing the password 
function on page 21 for details.
5. Switch all of the connected equipment on.
6. The projector will start to search for input 
signals. The current input signal being 
scanned displays in the upper left corner of 
the screen. If the projector doesnt detect 
a valid signal, the message “No Signal” will 
continue displaying until an input signal is 
found.
You can also press SOURCE on the 
projector or remote control to select your 
desired input signal. See Switching input 
signal on page 23 for details.
If the frequency/resolution of the input signal exceeds the projectors operating range, you will see the 
message “Out of Range” displayed on the background screen. Please change to an input signal which is 
compatible with the projectors resolution or set the input signal to a lower setting. See Timing chart on 
page 53 for details. 
						

							Operation 18
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. 
These adjusters change the image height and projection angle. To adjust the projector:
1. Press the quick-release button and lift the 
front of the projector. Once the image is 
positioned where you want it, release the 
quick-release button to lock the foot in 
position.
2. Screw the rear adjuster foot to fine-tune the 
horizontal angle.
To retract the foot, hold up the projector while 
pressing the quick-release button, then slowly lower 
the projector. Screw the rear adjuster foot in a 
reverse direction.
If the projector is not placed on a flat surface or the 
screen and the projector are not perpendicular to 
each other, the projected image becomes 
trapezoidal. To correct this situation, see Switching 
input signal on page 23 for details.
Auto-adjusting the image
In some cases, you may need to optimize the picture quality. To do this, press AUTO on 
the projector or remote control. Within 3 seconds, the built-in Intelligent Auto 
Adjustment function will re-adjust the values of Frequency and Clock to provide the best 
picture quality. 
The current source information will be displayed in the corner of the screen for 3 seconds.
This function is only available when PC signal (analog RGB) is selected.
Fine-tuning the image size and clarity
21
Do not look into the lens while the 
lamp is on. The strong light from the 
lamp may cause damage to your eyes.
Be careful when you press the quick-
release button as it is close to the 
exhaust vent where hot air comes 
from.
1. Adjust the projected image to the 
size that you need using the zoom 
ring. 2. Sharpen the image by rotating the 
focus ring.  
						

							Operation 19
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either 
the top or bottom. It occurs when the projector is not perpendicular to the screen. 
To correct this, you will need to manually correct it following ONE of these steps.
•  Using the remote control
Press  /  on the projector or remote control 
to display the Keystone correction page. Press   
to correct keystoning at the top of the image. Press 
 to correct keystoning at the bottom of the 
image.
•  Using the OSD menu
1. Press MENU/EXIT and then press  /  until the DISPLAY menu is highlighted.
2. Press  to highlight Keystone and press MODE/ENTER. The Keystone 
correction page displays.
3. Press   to correct keystoning at the top of the image. Press   to correct 
keystoning at the bottom of the image.
Press/.Press /. 
						

							Operation
20
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various 
adjustments and settings.
The OSD screenshots below are for reference on ly, and may differ from the actual design.
Below is the overview of the OSD menu.
The following example describes how to set the OSD language.
1. Press  MENU/EXIT  on the projector or 
remote control to turn the OSD menu on. 3. Press  to highlight 
Language 
and press  /  to select a 
preferred language.
2. Use  /  to highlight the  SYSTEM 
SETUP: Basic  menu. 4. Press
 MENU/EXIT  twice* on 
the projector or remote control 
to leave and save the settings.
*The first press leads you back to the 
main menu and the second press closes 
the OSD menu.
Current input signal
Main menu icon
Main menu
Sub-menu
Highlight
Press MENU/
EXIT  to the 
previous 
page or to 
exit.
Sta tu s
DISPLAYWall Color
Aspect Ratio
Keystone
PositionPhase
H. Size
Digital Zoom Off
Auto
0
0ENTER
MENU Exit
Analog RGB
3D Sync Frame Sequential
3D Sync Invert Disable
Teaching Template
DISPLAYWall Color Aspect Ratio
Position Phase
H. Size
Digital Zoom Keystone
Analog RGB Off
Auto
0
0
MENU Exit
3D Sync Frame Sequential
3D Sync Invert Disable
Teaching Template
SYSTEM SETUP: BasicPresentation Timer EnglishLanguageProjector Position
Operation Settings
Panel Key Lock
Splash Screen Background Color
Analog RGB
MENU Exit
Front Table Off
BenQ
BenQMenu Settings
SYSTEM SETUP: BasicPresentation Timer
English
Language
Projector Position
Operation Settings
Panel Key Lock
Splash Screen Background Color
Analog RGB
MENU Exit
Front Table Off
BenQ
BenQ
Menu Settings