BenQ Pg2401pt User Manual

							  21   How to assemble your monitor hardware
Adjusting the monitor height
To adjust the monitor height, hold both the left and the 
right sides of the monitor to lower the monitor or lift 
it up to the desired height.
• Avoid placing hands on the upper or lower part of the 
height-adjustable stand or at the bottom of the monitor, as 
ascending or descending monitor might cause personal 
injuries. Keep children out of reach of the monitor while 
performing this operation.
• If the monitor has been rotated to portrait mode and height adjustment is desired, you should 
be noted that the wide screen will keep the monitor from being lowered to its minimum 
height.
 
						

							22  How to assemble your monitor hardware  
Rotating the monitor
1. Pivot the display.
Before rotating the monitor with a portrait viewing orientation, the display has to be rotated 90 
degrees.
Right-click the desktop and select 
Screen resolution from the popup menu. Select Portrait in 
Orientation, and apply the setting.
Depending on the operating system on your PC, different procedures should be followed to adjust the screen 
orientation. Refer to the help document of your operating system for details.
2. Pivot the OSD menu.
Once the display is rotated, you also need to rotate the OSD menu.
Go to 
System and Auto Pivot. Select On. The OSD menu rotates with the monitor.
3. Fully extend the monitor and tilt it.
Gently lift the display up and extend it to the maximum 
extended position. Then tilt the monitor.
The monitor should be vertically extended to allow to rotate 
from landscape to portrait mode.
4. Rotate the monitor 90 degrees clockwise as 
illustrated.
To avoid the edge of the LCD display hitting the monitor base 
surface while it is being rotated, do tilt and extend the monitor 
to the highest position before you start to rotate the display. You 
should also make sure there are no obstacles around the monitor 
and there is enough room for cables.
 
						

							  23   How to assemble your monitor hardware
Viewing angle adjustment
You may position the screen to the desired angle with -5° to + 20° monitor tilt, 90° (left and 
right total) monitor swivel, and 150 mm monitor height.
5. Adjust the monitor to the desired viewing 
angle.
-5-5O O ~ +20~ +20O-5O ~ +20O-45-45O O ~ +45~ +45O-45O ~ +45O150 mm150 mm
 
						

							24  How to assemble your monitor hardware  
Using the monitor wall mounting kit
The back of your LCD monitor has a VESA standard mount with 100mm pattern, allowing the 
installation of a wall mount bracket. Before starting to install a monitor wall mounting kit, 
please read the precautions carefully.
Precautions
• Install your monitor and monitor mounting kit on a wall with flat surface.
• Ensure that the wall material is stable to support the weight of the monitor.
• Turn off the monitor and the power before disconnecting the cables from the LCD monitor.
1. Remove the monitor stand.
Lay the screen face down on a clean and well-padded 
surface. Detach the monitor stand as instructed in step 
1~2 in How to detach the stand and the base on page 
16.
2. Remove the screws on the back cover.
Use a cross-pointed screwdriver to release the screws 
on the back cover. The use of a magnetic-head 
screwdriver is recommended to avoid of losing the 
screws.
In case you intend to use your monitor on the stand in the 
future, please keep the monitor base, monitor stand, and 
screws somewhere safe for future use.
3. Follow the instruction manuals of the wall 
mount bracket you purchased to complete 
the installation.
 
						

							  25   Getting the most from your BenQ monitor
Getting the most from your BenQ monitor
To gain the most benefit from your new BenQ LCD monitor, you should install the custom 
BenQ LCD Monitor driver software as provided on the BenQ LCD Monitor DVD-ROM.
The circumstances under which you connect and install your BenQ LCD Monitor will 
determine which process you need to follow to successfully install the BenQ LCD Monitor 
driver software. These circumstances relate to which version of Microsoft Windows you are 
using, and whether you are connecting the monitor and installing the software onto a new 
computer (without existing monitor driver software), or whether you are upgrading an existing 
installation (which already has existing monitor driver software) with a newer monitor.
In either case however, the very next time you turn on your computer (after connecting the 
monitor to your computer), Windows will automatically recognize the new (or different) 
hardware, and will launch its 
Found New Hardware wizard.
Follow the wizard instructions until it asks you to select a monitor model. At that point, click 
the 
Have Disk button, insert the BenQ LCD Monitor DVD-ROM and select the appropriate 
monitor model. Further details and step-by-step instructions for either an automatic (new) or 
upgrade (existing) installation, see:
• How to install the monitor on a new computer on page 26.
• How to upgrade the monitor on an existing computer on page 27.
• If you require a User Name and Password to login to your Windows computer, you must be logged on as an 
Administrator or as a member of the Administrators group in order to install the monitor driver software. 
Furthermore, if your computer is connected to a network which has security access requirements, network 
policy settings may prevent you from installing software on your computer.
• To check the name of the purchased model, refer to the specification label on the back of the monitor.
 
						

							26  Getting the most from your BenQ monitor  
How to install the monitor on a new computer
This instruction details the procedure for selecting and installing the BenQ LCD Monitor driver 
software on a new computer which has never had a monitor driver installed before. This 
instruction is only suitable for a computer which has never been used before, and for which the 
BenQ LCD Monitor is the first ever monitor to be connected to it.
1.  Follow the instructions in How to assemble your monitor hardware on page 10. 
When Windows starts, it will automatically detect the new monitor and launch the Found New 
Hardware Wizard. Follow the prompts until it displays the option to Install Hardware Device 
Drivers.
2.  Insert the BenQ LCD Monitor DVD-ROM into a DVD drive on the computer.
3.  Check 
Search for a suitable driver for my device option, and click Next.
4.  Check the option for DVD-ROM drives (uncheck all others) and click 
Next.
5.  Look to confirm that the wizard has selected the correct name of your monitor and click 
Next.
6.  Click 
Finish.
7.  Restart the computer.
If you are adding the BenQ LCD Monitor to an existing computer that has already had another monitor 
connected to it (and has monitor driver software installed), you should not be following these instructions. You 
should instead be following the instructions for How to upgrade the monitor on an existing computer.
 
						

							  27   Getting the most from your BenQ monitor
How to upgrade the monitor on an existing computer
This instruction details the procedure for manually updating the existing monitor driver 
software on your Microsoft Windows computer. It is currently tested as compatible for Mac 
OS, Windows 8, and Windows 7 Operating System (OS). 
Installing monitor driver software involves selecting an appropriate information file (.inf) on the 
BenQ LCD Monitor DVD-ROM for the particular model monitor you have connected, and 
letting Windows install the corresponding driver files from the DVD. You need only steer it in 
the right direction. Windows has an Upgrade Device Driver Wizard to automate the task and 
guide you through the file selection and installation process. 
See:
• How to install on Windows 8 system on page 28.
• How to install on Windows 7 system on page 29.
The BenQ LCD Monitor driver for your model may well function perfectly with other versions of Windows, 
however, as at the time of writing, BenQ has done no testing of this driver on other versions of Windows and 
cannot guarantee its operation on those systems.
 
						

							28  Getting the most from your BenQ monitor  
How to install on Windows 8 system
1.  Open Display Properties.
Move the cursor to the lower-right of the screen or press the Windows + C buttons on the 
keyboard to bring up the Charm bar. Go to Settings, Control Panel, Devices and Printers 
and right-click the name of your monitor from the menu.
Alternatively, right-click the desktop and select Personalize, Display, Devices and Printers, 
and right-click the name of your monitor from the menu.
2.  Select Properties from the menu.
3.  Click the 
Hardware tab.
4.  Click 
Generic PnP Monitor, and then the Properties button.
5.  Click the 
Driver tab and the Update Driver button.
6.  Insert the BenQ LCD Monitor DVD-ROM into a DVD drive on the computer.
7.  In the 
Update Driver Software window, select the option Browse my computer for 
driver software
.
8.  Click 
Browse and navigate to the following directory: d:\BenQ_LCD\Driver (where d is 
the drive letter designator for the DVD-ROM drive).
9.  Select the correct folder name of your monitor from provided driver list, and click 
Next.
This will copy and install the appropriate monitor driver files to your computer.
10. Click Close.
You may be prompted to restart your computer after the driver update is complete.
The drive letter for your DVD drive may differ from the example above depending upon your system - it may be 
D: or E: or F: etc.
 
						

							  29   Getting the most from your BenQ monitor
How to install on Windows 7 system
1.  Open Display Properties.
Go to Start, Control Panel, Hardware and Sound, Devices and Printers and right-click the 
name of your monitor from the menu.
Alternatively, right-click the desktop and select Personalize, Display, Devices and Printers, 
and right-click the name of your monitor from the menu.
2.  Select Properties from the menu.
3.  Click the 
Hardware tab.
4.  Click 
Generic PnP Monitor, and then the Properties button.
5.  Click the 
Driver tab and the Update Driver button.
6.  Insert the BenQ LCD Monitor DVD-ROM into a DVD drive on the computer.
7.  In the 
Update Driver Software window, select the option Browse my computer for 
driver software
.
8.  Click 
Browse and navigate to the following directory: d:\BenQ_LCD\Driver (where d is 
the drive letter designator for the DVD-ROM drive).
9.  Select the correct folder name of your monitor from provided driver list, and click 
Next.
This will copy and install the appropriate monitor driver files to your computer.
10. Click Close.
You may be prompted to restart your computer after the driver update is complete.
The drive letter for your DVD drive may differ from the example above depending upon your system - it may be 
D: or E: or F: etc.
 
						

							30  How to adjust your monitor  
How to adjust your monitor
The control panel
No.NameDescription
1.   Control keys Accesses the functions or menu items displayed on the screen, 
right next to each key.
2.   Power key Turns the power on or off.
12
The control keys are embedded in a touchpad and are indicated by the LED indicators. Touch of an LED indicator 
represents pressing the corresponding control key.