BenQ Pe7700 Users Manual

							  31
  Additional information
English4. Loosen the screws that hold the lamp to the projector. If the screws are not 
loosened completely, they could injure your fingers. It is strongly 
recommended that you use a magnetic-head screwdriver to retain the screw 
should it come loose 
5. Slowly pull the lamp out of the projector.
Pulling it too quickly may cause the lamp to break and scatter broken glass in 
the projector. To reduce the risk of injuries to fingers and damage to internal 
components, use caution when removing lamp glass that has shattered.
Do not place the lamp in locations where water might splash on it, children 
can reach it, near or above heat sources, or near flammable materials.
Do not insert your hands into the projector after the lamp is removed. If you 
touch the optical components inside, it could cause color unevenness and distortion of the projected 
images.
6. Insert a new lamp. Make sure it is securely in place.
7. Tighten the screws securing the lamp box.
8.  Re-install the lamp cover. 
9.  Tighten the screws on the lamp cover.
Do not over tighten the screws.
Loose screws may cause a bad connection, which could result in malfunction.
10.  Turn the power on and go into Setup > Lamp > Reset Lamp Timer menu to 
reset the lamp time.
Do not turn the power on with the lamp cover removed. 
Whenever the lamp is replaced, reset the total lamp operation time. 
Do not reset if the lamp is not replaced as this could cause damage.
PE7700-e.book  Page 31  Monday, January 10, 2005  11:20 AM
Downloaded From projector-manual.com BenQ Manualr 
						

							32 Additional information  
EnglishIndicators
There are three indicators which show the status of the projector. Check the following for information about the 
indicator lights. If there is anything wrong, turn the projector off and contact your dealer. 
When the projector is in a normal state, ... 
When the projector is in an abnormal state, ... 
POWER TEMP LAMP STATE REMARK
Orange
Off OffStandby mode.
Flashing 
orangeThe projector is powering up. Cannot turn the projector off.
GreenThe projector is under normal 
operation.
Flashing 
green(1) The projector needs 110 
seconds to cool down as it 
was abnormally shut down 
without the normal cooling 
down process. Or
(2) The projector needs to cool 
for 110 seconds after the 
power is turned off.Cannot turn the projector on.
POWER TEMP LAMP STATE REMARK
Orange Off Red(1) The lamp has exceeded its 
usage life. Or
(2) The lamp is not properly 
attached or is damaged.Solution:• Install a new lamp.
• Please contact your dealer for 
assistance.
Orange  Red OffThe dust filter is seriously clogged 
with dust. The projector is going to 
shut down.Solution:• Install a new filter.
Orange Red OffThe internal temperature is too 
high.
• The intake ventilation or the 
exhaust ventilation is blocked.
• The projector may be in a poorly 
ventilated location.
• The ambient temperature may 
be too high.
Solution:
• Make sure that the ventilation 
holes are not blocked.
• Relocate the projector.
• Stop using the projector until 
the ambient temperature falls 
within the specified range. The 
maximum operating 
temperature is specified as 40°C 
/ 104°F.
OrangeFlashing 
redFlashing 
redThe fans are not working.Solution:
• Check if the power supply is 
stable.
• Check if there is object stuck in 
the fans.
• Contact your dealer.
PE7700-e.book  Page 32  Monday, January 10, 2005  11:20 AM
Downloaded From projector-manual.com BenQ Manualr 
						

							  33
  Additional information
EnglishTroubleshooting
ProblemCauseRemedy
The projector does 
not turn on.
There is no power from the power 
cable.Plug the power cable into the AC inlet on 
the rear of the projector, and plug the 
power cable into to the power outlet. If the 
power outlet has a switch, make sure that it 
is switched on. (Page 19)
The power switch is not in the on 
position.Put the power switch in the on position. 
(Page 19)
Attempting to turn the projector on 
again during the cooling process.Wait until the cooling down process has 
completed.
The lamp cover is not securely 
attached.Correctly attach the lamp cover. (Page 30)
No picture.
The video source is not turned on 
or connected correctly.Turn the video source on and check that 
the signal cable is connected correctly. 
(Page 17)
The projector is not correctly 
connected to the input source 
device.Check the connection. (Page 17)
The input signal has not been 
correctly selected.Select the correct input signal with the 
Source buttons on the remote control or 
SOURCE / ENTER on the projector. (Page 
19)
Image is unstable.
The connection cables are not 
securely connected to the projector 
or the signal source.Correctly connect the cables to the 
appropriate terminals. (Page 17)
Picture is blurred.
The projection lens is not correctly 
focused.Adjust the focus of the lens using the focus 
ring. (Page 20)
The projector and the screen are 
not aligned properly.Adjust the projection angle and direction as 
well as the height of this unit if necessary. 
(Page 20)
The lens cap is still attached to the 
lensRemove the lens cap. (Page 19)
Remote control 
does not work 
correctly
The batteries are out of power. Replace both of the batteries with new 
ones. (Page 10)
There is an obstacle between the 
remote control and the projector.Remove the obstacle. (Page 12)
You are too far away from the 
projector.Stand within 8 meters (26.2 feet) of the 
projector. (Page 12)
PE7700-e.book  Page 33  Monday, January 10, 2005  11:20 AM
Downloaded From projector-manual.com BenQ Manualr 
						

							34 Additional information  
EnglishSpecifications
All specifications are subject to change without notice. 
Dimensions
Unit: mm
Optical characteristics
Projection systemSingle-chip DLPTM system.
DMD chip0.8” DMD W_Pal (1280 x 720)
Lens1.37-times zoom ratio, F/# 2.4 ~ 2.8, f = 24 ~ 32
Projection size0.94 m to 7.62 m / 37 to 300 inches
Lamp250W
Electrical characteristics
Color systemNTSC / PAL-M / PAL-N / PAL 60 / SECAM
ResolutionXGA, SVGA, VGA, Macintosh
®, 
HDTV (1080i, 720p, 576p, 576i, 480p, 480i)
Max. number of display colors16,770,000 colors (full color display)
Input
Video, S-Video, Component (Y/ CB/ CR, Y/ PB/ PR)
RS-232C, RGBHV, HDMI
General characteristics
Dimensions 380 mm x 300 mm x 115 mm (L x W x H)
We i g h t10 lbs / 7.6 kg
PowerVAC 100 - 240V, 4.0 A, 50 / 60 Hz (Automatic)
Power consumptionMax 320 W
Operating temperature0 °C to 40 °C at sea level
Operating humidity10% - 90% (without condensation)
Operating altitude6000 feet at 30°C, 6000 - 10000 feet at max. 23°C
Storage temperature-10°C- 60°C / 14°F to 140°F
Storage humidity10% - 90%
PE7700-e.book  Page 34  Monday, January 10, 2005  11:20 AM
Downloaded From projector-manual.com BenQ Manualr