BenQ Pe7700 Users Manual

  21
  Using the projector and remote control
English1. Selecting a preset mode
Select a preset mode on the remote control, or in Picture > Preset Mode menu. 
There are 5 modes available for each input. These modes are with preset values 
suitable for various projection purposes.
QPreset Cinema Mode: with well-balanced color saturation and contrast 
but lowest brightness. It is suitable for enjoying dark movie contents in a 
totally dark environment.
QPreset Home Theater Mode: is brighter than Cinema...

22 Using the projector and remote control  
EnglishPersonalizing the projector menu display
The On Screen Display (OSD) menus can be set according to your preferences. These settings will not affect the 
projection settings, operation, or performance.
•Language in Setup menu sets your familiar language for the on-screen menus.
• You can select projector’s Background Color from purple, black or white in Options menu.
•OSD Off (Secs) in Options Menu sets the length of time the OSD will remain active after...

  23
  Using the projector and remote control
EnglishPIP --- 
POP --- 
Tu r n i n g  t h e  p o w e r  o f f
Follow the steps below.
1. Press the POWER button on the projector or remote control and a 
warning message appears. To turn the projector off, press POWER 
again.
2. The Power indicator light flashes green and the fans run for about two 
minutes to cool the lamp. The projector will not respond to any 
commands until the cooling process is complete.
3. Then, the Power indicator light is a steady...

24 Menus  
EnglishMenus
Menu structure
Picture Contrast Preset Cinema Mode
Preset Home Theater Mode
Preset Family Room Mode
Preset Photo Mode
Preset Gaming ModeUser1
User2
Warm
Normal
Cool Brightness
Color
Tint
Noise Reduce
Filter
Sharpness Color Temp. Red
Green
Blue
Yellow
White Preset Mode Color Enhancement
Extended Picture Settings
Save Settings To User’s Memory 1
To User’s Memory 2
To User’s Memory 3 Load Settings
User Memory 1, User Memory 2, User Memory 3, Default
Display Aspect Ratio Anamorphic,...

  25
  Menus
EnglishUsing the menus
The projector is equipped with on-screen display (OSD) menus for making 
various adjustments and settings.
There are eight different menu languages. Refer to Setup Menu on page  27 for 
more details. 
The following example describes the adjustment of the keystone.
Picture menu
The functions provided in this menu are aiming to  adjust image quality by yourself. Before making 
adjustments, you are suggested to choose a desired preset  mode in this menu which has set...

26 Menus  
English6.Filter: Turn the video and data filters on or off. Filters can reduce noise in the picture to produce a sharper 
image. The higher the setting, the less the noise.
7.Sharpness: Adjusts the picture sharpness. The higher the value, the sharper the picture. 
8.Preset Mode: Preset modes are provided so you can optimize your projector image set-up to suit your 
program type. Refer to page 21 for more information.
9. Extended Picture Settings
QColor Temp.: You can choose a preferred color...

  27
  Menus
English6.PIP/POP Source Selection: Selects the input signal that will be displayed as the PIP or POP image.
Video --- 
QVideo: Composite video signal.
QS-Video: S-Video video signal.
Graphics ---
QComponent 1 and 2: Component Y/CB/CR and Y/PB/PR input
QRGBHD: DTV RGBHD signal input
QHDMI
In the unlikely event that the image shakes when PIP or POP function is activated, we suggest you to 
change the input signals. The shaking image may be caused by the combination of Y/CB/CR and Video, 
or...

28 Menus  
Englishshould switch to Ye s to solve these symptoms. However, this is not to state that this projector can operate 
under any and all harsh and extreme environments.
5.Black level: The grayscale video signal is measured in IRE units. In some areas which use NTSC TV standard, 
the grayscale is measured from 7.5 IRE (black) to 100 IRE (white); however, in other areas which use PAL 
equipment or Japanese NTSC standard, the grayscale is measured from 0 IRE (black) to 100 IRE (white). We 
suggest...

  29
  Additional information
English
Additional information
Care of the projector
Your projector needs little maintenance. The only thing you have to do on a regular basis is keep the lens clean. 
Never remove any parts of the projector except the lamp. Contact your dealer if other parts needs replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface. Before you attempt to clean the lens, turn the 
projector off, unplug the power cable, and leave it several minutes to...

30 Additional information  
English4. Use a small vacuum cleaner designed for computers and other office 
equipment to clean the filter. Or use a soft brush (such as a clean artist’s 
paintbrush) to gently sweep the dust away.
QIf the dirt is difficult to remove or the filter is broken, contact your place 
of purchase to replace it.
5. Re-install the filter grill securely.
QIf the filter grill is not correctly seated in place, you 
will be reminded by a message displayed on the 
screen every three...