BenQ Mx716/mx717 Digital Projector User Manual

Operation 31
3D Color Management
In most installation situations, color management will not be necessary, such as in 
classroom, meeting room, or lounge room situations where lights remain on, or where 
building external windows allow daylight into the room. 
Only in permanent installations with controlled lighting levels such as boardrooms, lecture 
theaters, or home theaters, should color management be considered. Color management 
provides fine color control adjustment to allow for more accurate color...

Operation 326. Press  to highlight Gain and adjust its values to your preference by pressing  /
. The contrast level of the primary color you select will be affected. Every 
adjustment made will reflect to the image immediately. 
7. Repeat steps 3 to 6 for other color adjustments.
8. Make sure you have made all of the desired adjustments.
9. Press MENU/EXIT to exit and save the settings.
Setting the presentation timer
Presentation timer can indicate the presentation time on the screen to help you achieve...

Operation 33
To cancel the timer, perform the following steps:
1. Go to the SYSTEM SETUP: Basic > Presentation Timer menu and highlight 
Off. Press ENTER. A confirmation message displays.
2. Highlight Ye s and press ENTER to confirm. You will see the message “Timer is 
Off” displaying on the screen. 
Remote paging operations
Connect the projector to your PC or notebook with a USB cable prior to using the paging 
function. See Connection on page 17 for details.
You can operate your display software...

Operation 341. Go to the SYSTEM SETUP: Basic > Panel Key Lock menu, and select On by 
pressing  /  on the projector or remote control. A confirmation message 
displays. 
2. Highlight Ye s and press ENTER to confirm.
To release panel key lock, use the remote control to enter the 
SYSTEM SETUP: 
Basic > 
Panel Key Lock menu and press  /  to select Off.
•  Keys on the remote control are still active when panel key lock is enabled.
•  If you turn off the projector without disabling panel key lock, the...

Operation 35 1. Press MENU/EXIT and then press  /  until the SYSTEM SETUP: Basic menu 
is highlighted.
2. Press  to highlight MyScreen and press ENTER.
3. Repeat steps 2-5 in the Using the remote control section to capture and view the 
captured picture.
In the unlikely event that the capturing action fails, change your target picture. Large-sized 
pictures may cause the capturing action to fail. If so, please choose a smaller one and try 
again.
Adjusting the sound
The sound adjustments made as below...

Operation 36
Controlling the projector through a LAN 
environment
You can manage and control the projector from one or more remote computers when 
they are properly connected to the same local area network.
Cable connection
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector 
and the other end to the RJ45 port on your Ethernet or router.
2. Do one of the following: 
•Press NETWORK SETTING on the remote control. The Network 
Settings page...

Operation 37 5. Press  /  to move the cursor and the press  /  to enter the value.
6. To save the settings, press ENTER. If you do not want to save the settings, press 
MENU/EXIT.
7. Press  to highlight Apply and press ENTER.
Controlling the projector remotely through a web 
browser
Once you have the correct IP address for the projector and the projector is on or in 
standby mode, you can use any computer that is on the same local area network to control 
the projector.
•  If you are using Microsoft...

Operation 38The tools page allows you to manage the projector, configure the Network settings and 
secure access of remote network operation on this projector.
i. You can name the projector, keep track of its location and the person in charge 
of it.
ii. You can adjust the Network Settings.
iii. Once set, access to the remote network operation on this projector has been 
password-protected.
iv. Once set, access to the tools page has been password-protected.
After making the adjustments, press the Send...

Operation 39
Shutting down the projector
1. Press  POWER or   OFF and a confirmation message will display prompting 
you. 
If you dont respond in a few seconds, the message will disappear.
2. Press  POWER or   OFF a second time. The POWER indicator light 
flashes orange, the projection lamp shuts down, and the fans will continue to run for 
approximately 90 seconds to cool down the projector.
To protect the lamp, the projector will not respond to any commands during the cooling process.
To shorten the...

Operation 40
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type 
selected and the projector model you are using.
Main menu Sub-menu Options
1. 
DISPLAY
Wall ColorOff/Light Yellow/Pink/Light 
Green/Blue/Blackboard
Aspect Ratio Auto/Real/4:3/16:9/16:10
Auto Keystone On/Off
Keystone
Position
Phase
H. Size
Digital Zoom
3D SyncOff/Frame Sequential/Top-
Bottom
3D Sync Invert Disable/Invert
Teaching 
TemplateBlackboardOff/Letter Formation/Worksheet/...