BenQ Mw814st Digital Projector User Manual

Operation 31
3D Color Management
In most installation situations, color management will not be necessary, such as in 
classroom, meeting room, or lounge room situations where lights remain on, or where 
building external windows allow daylight into the room. 
Only in permanent installations with controlled lighting levels such as boardrooms, lecture 
theaters, or home theaters, should color management be considered. Color management 
provides fine color control adjustment to allow for more accurate color...

Operation 327. Repeat steps 3 to 6 for other color adjustments.
8. Make sure you have made all of the desired adjustments.
9. Press MENU/EXIT to exit and save the settings.
Setting the presentation timer
Presentation timer can indicate the presentation time on the screen to help you achieve 
better time management when giving presentations. Follow these steps to utilize this 
function:
1. Go to the SYSTEM SETUP: Basic > Presentation Timer menu and press MODE/
ENTER to display the Presentation Timer...

Operation 33
Remote paging operations
Connect the projector to your PC or notebook with a USB cable prior to using the paging 
function. See Connection on page 17 for details.
You can operate your display software program (on a connected PC) which responds to page 
up/down commands (like Microsoft PowerPoint) by pressing PAGE UP/PAGE DOWN on 
the remote control.
If remote paging function doesnt work, check if the USB connection is correctly made and 
the mouse driver on your computer is updated to the...

Operation 34
•  If you press    POWER to turn off the projector without disabling panel key lock, the 
projector will still be in locked status the next time it is turned on.
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 1500 m 
–3000 m above sea level, and ambient temperature is between 0°C–35°C.
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and ambient 
temperature is between 0°C and 35°C. The...

Operation 35
Adjusting the sound
The sound adjustments made as below will have an effect on the projector speaker. Be sure 
you have made a correct connection to the projector audio input. See Connection on page 
17 for how the audio input is connected.
Muting the sound
To temporarily turn off the sound:
1. Press MENU/EXIT and then press  /  until the SYSTEM SETUP: Advanced menu 
is highlighted.
2. Press   to highlight Audio Settings and press MODE/ENTER. The Audio Settings 
page displays.
3. Highlight...

Operation 362. Press MENU/EXIT and then press  /  until the SYSTEM SETUP: Advanced menu 
is highlighted. Press   to highlight Network Settings and press MODE/ENTER. The 
Network Settings page is displayed. 
3. Highlight Wired LAN and press MODE/ENTER.
4. Make sure the Status is Connect.
5. Press   to highlight DHCP and press  /  to select On. 
6. Press   to highlight Apply and press MODE/ENTER.
7. Re-enter the Network Settings page. The IP Address, Subnet Mask, Default Gateway, 
DNS and Mac Address...

Operation 37 2. The remote network operation page opens. This page allows you to operate the 
projector as if you were using the remote control or control panel on the projector. 
i. These buttons function the same as the ones on the OSD menus or remote 
control. See 1. DISPLAY menu on page 43 and Remote control on page 11 for 
details.
ii. To switch input source, click on your desired signal.
•  The Menu button can also be used to go back to previous OSD menu, exit and save menu 
settings.
•  The...

Operation 38iv. Once set, access to the tools page has been password-protected.
After making the adjustments, press the Send button and the data will be saved in the 
projector.
v. Press Exit to go back to the remote network operation page.
The info page displays the information and status of this projector.
6. For more information, visit http://www.crestron.com. If you are an IT administrator 
and would like to manage multiple devices through one interface, you can download 
Crestron Roomview at...

Operation 39
Shutting down the projector
1. Press  POWER and a confirmation message will display prompting you. 
If you dont respond in a few seconds, the message will disappear.
2. Press  POWER a second time. The POWER indicator light flashes orange, the 
projection lamp shuts down, and the fans will continue to run for approximately 90 
seconds to cool down the projector.
To protect the lamp, the projector will not respond to any commands during the cooling 
process.
To shorten the cooling time, you...

Operation 40
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type 
selected and the projector model you are using.
Main menu Sub-menu Options
1. 
DISPLAY
Wall ColorOff/Light Yellow/Pink/Light 
Green/Blue/Blackboard
Aspect Ratio Auto/Real/4:3/16:9/16:10
Keystone
Position
Phase
H. Size
Digital Zoom
3D Sync Off/Frame Sequential/Top-Bottom
3D Sync Invert Disable/Invert
Teaching 
TemplateBlackboardOff/Letter Formation/Worksheet/
Coordinate Chart...