BenQ Mw724 Users Manual

							
Operation 41
Only in permanent installations with controlled lighting levels such as boardrooms, 
lecture theaters, or home theaters, should color management be considered. Color 
management provides fine color control adjusent to allow for more accurate color 
reproduction, should you require it.
Proper color management can only be achieved under controlled and reproducible 
viewing conditions. You will need to use a colorimeter (color light meter), and 
provide a set of suitable source images to measure color reproduction. These tools 
are not provided with the projector, however, your projector supplier should be able 
to provide you with suitable guidance, or even an experienced professional installer.
The Color Management provides six sets (RGBCMY) of colors to be adjusted. When 
you select each color, you can independently adjust its range and saturation according 
to your preference.
If you have purchased a test disc which contains various color test patterns and can be 
used to test the color presentation on monitors, TVs, projectors, etc. You can project 
any image from the disc on the screen and enter the 
3D Color Management menu 
to make adjusents.
To adjust the settings:
1. Go to the  PICTURE menu and select  3D Color Management .
2. Press  Mode/Enter  and the 3D Color Management  page displays.
3. Select  Primary Color  and press  /  to select a color from among Red, 
Yellow, Green, Cyan, Blue, or Magenta.
4. Press   to select  Hue and press  /  
to select its range. Increase in the range 
will include colors consisted of more 
proportions of its two adjacent colors. 
Please refer to the illustration to the right 
for how the colors relate to each other. 
For example, if you select Red and set its 
range at 0, only pure red in the projected 
picture will be selected. Increasing its 
range will include red close to yellow and 
red close to magenta.
5. Press  to select  Saturation and adjust 
its values to your preference by pressing  / . Every adjusent made will reflect 
to the image immediately. 
For example, if you select Red and set its value at 0, only the saturation of pure 
red will be affected.
• Saturation  is the amount of that color in a video picture. Lower settings produce 
less saturated colors; a setting of “0” removes that color from the image entirely. If 
the saturation is too high, that color will be overpowering and unrealistic.
6. Press   to select  Gain and adjust its values to your preference by pressing  /
. The contrast level of the primary color you select will be affected. Every 
adjusent made will reflect to the image immediately. 
7. Repeat steps 3 to 6 for other color adjusents.
8. Make sure you have made all of the desired adjusents.
RED
BLUEGREEN
Ye l l o w
Cyan
Magenta
Downloaded From projector-manual.com BenQ Manuals 
						

							
Operation
42 9. Press 
Menu/Exit  to exit and save the settings.
Resetting current or all picture modes
1. Go to the  PICTURE menu and select  Reset Picture Settings .
2. Press  MODE/ENTER  and press  /  to select  Current or All.
• Current : returns current picture mode to the factory preset settings.
• All: returns all settings, except  User 1/User 2 in the PICTURE  menu to the 
factory preset settings.
Downloaded From projector-manual.com BenQ Manuals 
						

							
Operation 43
Setting the presentation timer
The presentation timer can indicate the presentation time on the screen to help you 
achieve better time management when giving presentations. Follow these steps to 
utilize this function:
1. Go to the SYSTEM SETUP: Basic > Presentation Timer  menu and press 
Mode/Enter  to display the  Presentation Timer  page.
2. Select  Timer Period  and decide the timer period by pressing  / . The 
length of time can be set from 1 to 5 minutes in 1-minute increments and 5 to 
240 minutes in 5-minute increments.
3. Press   to select  Timer Display and choose if you want the timer to show up 
on the screen by press
ing /.
4. Press   to select  Timer Position and set the timer position by pressing  /
.
Top-LeftBottom-Left Top-Right Bottom-Right
5. Press   to select  Timer Counting Direction  and select your desired 
counting direction by pressing /
.
6. Press   to select  Sound reminder and decide if you want to activate sound 
reminder by pressing  / . If you select  On, a double beep sound will be 
heard at the last 30 seconds of counting down/up, and a triple beep sound will 
be produced when the timer is up.
7. To activate the presentation timer, press   and press  /  to select  On and 
press  Mode/Enter .
8. A confirmation message displays. Select  Ye s and press  Mode/Enter  to confirm. 
You will see the message “ Timer is On” displaying on the  screen. The timer 
starts counting at the time the timer is on.
To cancel the timer, perform the following steps:
1. Go to the  SYSTEM SETUP: Basic  > Presentation Timer  menu and press 
select   to select  Off. Press  Mode/Enter . A confirmation message displays.
2. Select  Ye s and press  Mode/Enter  to confirm. You will see the message 
“ Timer is Off! ” displaying on the screen.
SelectionDescription
Always Displays the timer on screen throughout the presentation time.
1 Min/2 Min/3 
Min  Displays the timer on screen in the last 1/2/3 minute(s).
Never Hides the timer throughout the presentation time.
SelectionDescription
Count Up Increases from 0 to the preset time.
Count Down Decrease from the preset time to 0.
Downloaded From projector-manual.com BenQ Manuals 
						

							
Operation
44
Hiding the image
In order to draw the audiences full attention to 
the presenter, you can use  ECO BLANK to hide 
the screen image. Press any key on the projector 
or remote control to restore the image. Eco Blank 
wording appears at the screen while the image is 
hidden. When this function is activated with an 
audio input connected, the audio can still be 
heard.
You can set the blank time in the  SYSTEM 
SETUP: Basic  > Operation Settings  > Blank Timer  menu to let the projector 
return the image automatically after a period of time when there is no action taken on 
the blank screen. The length of time can be set from 5 to 30 minutes in 5-minute 
increments.
• Do not block the projection lens from projecting as this could cause the 
blocking object to become heated.
• No matter Blank Timer is activated or not, you can press any key on  the projector or remote control to restore the picture.
Freezing the image
Press  FREEZE  on the remote control to freeze the image. The word FREEZE will 
display in the screen. To release the function, press any key on the projector or 
remote control.
Even if an image is frozen on the screen, the pictures are running on the video or 
other device. If the connected devices have active audio output, you will still hear the 
audio even though the image is frozen on screen.
Operating in a high altitude environment
We recommend you use the  High Altitude Mode when your environment is 
between 1500 m –3000 m above sea level, and ambient temperature is between 0°C–
35°C. 
Do not use the High Altitude Mode if your altitude is between 0 m and 
1500 m and ambient temperature is between 0°C and 35°C. The projector 
will be over cooled, if you turn the mode on under such a condition.
To activate the  High Altitude Mode :
1. Press  Menu/Exit  and then press  /  until the  SYSTEM SETUP: 
Advanced  menu is selected.
2. Press   to select  High Altitude Mode and press  /  to select  On. A 
confirmation message displays.
3. Select  Ye s and press  Mode/Enter .
Operation under  High Altitude Mode  may cause a higher decibel operating noise 
level because of increased fan speed necessary to improve overall system cooling and 
performance.
If you use this projector under other extreme conditions excluding the above, it may 
display auto shut-down symptoms, which is designed to protect your projector from 
Downloaded From projector-manual.com BenQ Manuals 
						

							
Operation 45
over-heating. In cases like this, you should switch to High Altitude mode to solve 
these symptoms. However, this is not to state that this projector can operate under 
any and all harsh or extreme conditions.
Adjusting the sound
The sound adjusents made as below will have an effect on the projector speaker(s). Be 
sure you have made a correct connection to the projector audio input. See 
Connection on page 21
 for how the audio input is connected.
Muting the sound
To adjust the sound level, press  MUTE on the remote 
control, or:
1. Press  Menu/Exit  and then press  /  until the 
SYSTEM SETUP: Advanced  menu is selected.
2. Press   to select  Audio Settings and press 
Mode/Enter . The Audio Settings page displays.
3. Select  Mute and select  On.
Adjusting the sound level
To adjust the sound level, press  Volume on the 
remote control or on the projector, or:
1. Repeat steps 1-2 above.
2. Select  VOLUME and select a desired sound level.
Turning off the Power on/off ring tone
To turn off the ring tone:
1. Repeat steps 1-2 in Muting the sound section.
2. Select  Power On/Off Ring Tone  and select Off.
The only way to change Power on/off ring tone is setting On or Off here. 
Setting the sound mute or changing  the sound level will not affect the 
Power on/off ring tone.
Adjusting the microphone’s sound level
To adjust the sound level:
1. Repeat steps 1-2 in Muting the sound section.
2. Select  Microphone Volume  and select a desired sound level.
Microphone sound will still function even though Mute is activated.
Downloaded From projector-manual.com BenQ Manuals 
						

							
Operation
46
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The 
following settings do not affect the projection settings, operation, or performance. 
• Language  in the SYSTEM SETUP: Basic  menu sets your familiar language for 
the OSD menus. Press  Mode/Enter to display language page. Use  / / /  
and  Mode/Enter  to select your language.
• Menu Display Time  in the SYSTEM SETUP: Basic  > Menu Settings  menu 
sets the length of time the OSD will remain active after your last key press. The 
time length ranges from 5 to 30 seco nds in 5-second increments. Use  /  to 
select a suitable time frame.
• Menu Position  in the SYSTEM SETUP: Basic  > Menu Settings  menu sets 
the OSD position in five locations. Use  /  to select a preferred position. 
• Reminder Message  in the SYSTEM SETUP: Basic  > Menu Settings  menu 
sets whether to display reminder messages on screen. Use  /  to select your 
desired setting.
• Splash Screen  in the SYSTEM SETUP: Basic  menu sets a preferred logo 
screen to be displayed during projector start-up. Use  /  to select a screen.
Select the lamp saver mode
• Using the remote control. 
Press  LAMP MODE  and the lamp mode 
selection  bar appears. Use  /  to select 
Normal/Economic/SmartEco .
• Using the OSD menu.
1. Press  Menu/Exit  and then press  /  
until the  SYSTEM SETUP: Advanced  
menu is selected.
2. Press   to select  Lamp Settings and press Mode/Enter . The Lamp Settings 
page displays.
3. Select  Lamp Mode  and press  /  to select  Normal/Economic/
SmartEco .  The lamp brightness vary from the different lamp mode,see the 
description list in table below.
If the Economic mode or SmatEco mode is selected, the light output will 
be reduced and result in darker projected pictures.
Lamp ModeDescription
Normal Provides full lamp brightness
Economic Lower brightness to extend the lamp life and decreases the fan 
noise
SmartEco Adjusts the lamp power automatically depending on the 
content brightness level
Downloaded From projector-manual.com BenQ Manuals 
						

							
Operation 47
U s e  Te a c h i n g  Te m p l a t e
Making writing on the board easier for teachers, you can use build-in template by 
OSD.
Open the OSD menu and go to the DISPLAY > Teaching Template  . Choose 
Blackboard/Whiteboard  > Off /Letter Formation/Worksheet /Coordinate 
Chart . The Teaching Template displays.
Teaching 
TemplateWhiteboardBlackboard
Letter 
Formation
Wo r k s h e e t
Coordinate 
Chart
Downloaded From projector-manual.com BenQ Manuals 
						

							
Operation
48
Shutting down the projector
1. Press  Power on the projector. A 
confirmation message displays prompting 
you. 
If you dont respond in a few seconds, the 
message will disappear. If you use the 
remote control, press OFF to shut down 
the projector.
2. Press  Power on the projector a second 
time. The  POWER indicator light  flashes 
orange, the projection lamp shuts down, 
and the fans will continue to run to cool 
down the projector. 
• To protect the lamp, the projector will  not respond to any commands during 
the cooling process.
• To shorten the cooling time, you can also activate the Quick Cooling  function. See  Quick Cooling on page 60  for details.
3. Once the cooling process finishes, the  POWER indicator light is a steady 
orange and fans stop.
4. Disconnect the power cord from the power putlet if the projector will not be  used in an extended period of time.
• If the projector is not properly shut down, to protect the lamp, when  you attempt to re-start the projector, the fans will run for a few minutes 
to cool down. Press Power again to start the projector after the fans 
stop and the POWER indica tor light turns orange.
• Actual lamp lives may vary due to different environmental conditions  and usage.II
II
Downloaded From projector-manual.com BenQ Manuals 
						

							
Operation 49
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type 
selected.
Main menu Sub-menu Options
1. 
DISPLAY Wall Color
Off
/Light Yellow/Pink/Light 
Green/Blue/Blackboard
Aspect Ratio Auto /Real/4:3/16:9/16:10
2D Keystone
Corner Fit
Po s i t i o n
Phase
H. Size
Digital Zoom
3D 3D mode
Auto
/Top Bottom/Frame 
Sequential/Frame Packing/Side 
by Side/Off
3D Sync Invert Disable /Invert
Save 3D 
Settings
Apply 3D 
Settings
Teaching 
Te m p l a t e Blackboard
Off
/Letter Formation/
Worksheet/Coordinate Chart
Whiteboard Off
/Letter Formation/
Worksheet/Coordinate Chart
Downloaded From projector-manual.com BenQ Manuals 
						

							
Operation
50 2. 
PICTURE
Picture Mode
Dynamic
/Presentation /sRGB /Cinema /(3D)/
User 1 /User 2
Reference 
Mode Dynamic
/Presentation /sRGB /Cinema /(3D)
Brightness
Contrast
Color
Tint
Sharpness
Color 
Te m p e r a t u r e Cool/
Normal /Warm
Color 
Temperature 
Fine Tuning R Gain/G Gain/B Gain/R Offset/
G Offset/B Offset
3D Color 
Management Primary Color R
/G/B/C/M/Y
Hue
Saturation
Gain
Reset Picture 
Settings Current/All/
Cancel
3. SOURCE Quick Auto Search On
/Off
Color Space Conversion Auto /RGB/YUV
Downloaded From projector-manual.com BenQ Manuals