BenQ Mp723 Users Manual

Operation 31
Though the password function is disabled, you need to keep the old password in hand should 
you ever need to re-activate the password function by entering the old password.
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only 
display one full screen at a time. When starting up, the projector automatically search for the 
available signals.
Be sure the Quick Auto Search function in the SOURCE menu is On (which is the default of...

Operation 32
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These 
adjusters change the image height and projection angle. To adjust the projector:
1. Press the quick-release button and lift the front 
of the projector. Once the image is positioned 
where you want it, release the quick-release 
button to lock the foot in position.
2. Screw the rear adjuster foot to fine tune the 
horizontal angle.
To...

Operation 33
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the 
top or bottom. It occurs when the projector is not perpendicular to the screen. 
To correct this, besides adjusting the height of the projector, you will need to manually 
correct it following ONE of these steps.
• Press  /  on the control panel of the 
projector or remote control to display the 
Keystone correction page. Press   to 
correct keystoning at the top of the image....

Operation 343. Press   repeatedly to magnify the picture to a desired size.
4. To navigate the picture, press Mode/enter to switch to the paning mode and press the 
directional arrows ( ,  ,  ,  ) on the projector or remote control to navigate the 
picture.
5. To reduce size of the picture, press Mode/enter to switch back to the zoom in/out 
function, and press AUTO to restore the picture to its original size. You can also press 
 repeatedly until it is restored to the original size.
Selecting the aspect...

Operation 35 4.
Real: The image is projected as its original resolution, and resized to 
fit within the display area. For input signals with lower resolutions, 
the projected image will display smaller than if resized to full screen. 
You could adjust the zoom setting or move the projector towards the 
screen to increase the image size if necessary. You may also need to 
refocus the projector after making these adjustments.
OSD menus can be displayed on those unused black areas.
Optimizing the image...

Operation 36YPbPr/S-Video/Video/HDCP Signal Input
1.Dynamic mode: Is suitable for playing gamebox-based video games in a normal living 
room lighting level environment.
2.Standard mode (Default): Is appropriate for viewing colorful movies, video clips from 
digital cameras or DVs.
3.Cinema mode: Is suitable for enjoying dark movies or DVD movies best viewed in a 
blackened (little light) home cinema or lounge room environment.
4.User 1/User 2 mode: Recalls the settings customized based on the current...

Operation 37
Adjusting Color
Highlight Color in the PICTURE menu and adjust the values by pressing  / on the 
projector or remote control.
Lower setting produces less saturated colors; setting to the minimum value makes the image 
black and white. If the setting is too high, colors on the image will be overpowering, which 
makes the image unrealistic.
Adjusting Tint
Highlight Tint in the PICTURE menu and adjust the values by pressing  / on the 
projector or remote control.
The higher the value, the more...

Operation 38
3D Color Management
In most installation situations, color management will not be necessary, such as in 
classroom, meeting room, or lounge room situations where lights remain on, or where 
building external windows allow daylight into the room. 
Only in permanent installations with controlled lighting levels such as boardrooms, lecture 
theaters, or home theaters, should color management be considered. Color management 
provides fine color control adjustment to allow for more accurate color...

Operation 39 6. Press   to highlight Gain and adjust its values to your preference by pressing  / . 
The contrast level of the primary color you select will be affected. Every adjustment 
made will reflect to the image immediately. 
7. Repeat steps 3 to 6 for other color adjustments.
8. Make sure you have made all of the desired adjustments.
9. Press MENU/EXIT to exit and save the settings.
Setting the presentation timer
Presentation timer can indicate the presentation time 
on the screen to help you...

Operation 407. To activate the presentation timer, press   and 
press /  to highlight On and press Mode/
enter.
8. A confirmation message displays. Highlight Ye s 
and press Mode/enter on the projector or ENTER 
on the remote control to confirm. You will see the 
message “Timer is On” displaying on the screen. 
The timer start counting at the time the timer is 
on.
To cancel the timer, perform the following steps.
• Using the remote control
Press TIMER ON/SHOW and press  /  to highlight Off and press...