BenQ Mp612/mp612c/mp622c Digital Projector User Manual

Operation 31
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the 
top or bottom. It occurs when the projector is not perpendicular to the screen. 
To correct this, besides adjusting the height of the projector, you will need to manually 
correct it following ONE of these steps.
1. Press   or   on the control panel of 
the projector or remote control to display 
the status bar labelled Keystone. Press   
to correct keystoning at the top of the...

Operation 323. To restore the picture to its original size, press AU TO. You can also press D. ZO OM  -. 
When the key is pressed again, the picture is further reduced until it is restored to the 
original size.
• Using the OSD menu
1.
Press Menu/exit and then press Left or Right until the Display menu is highlighted.
2. Press Down to highlight Digital Zoom. 
3. Press Mode/enter and press Up to magnify the picture to a desired size.
4. Press Mode/enter to activate the Pan functionality.
5. Use the...

Operation 33
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined 
picture modes so that you can choose one to suit 
your operating environment and input source 
picture type.
To select a operation mode that suits your need, you 
can follow one of the following steps.
•Press Mode/enter on the remote control or 
projector repeatedly until your desired mode is 
selected.
• Go to the Picture > Picture Mode menu and press 
Left/Right to select a desired mode.
The...

Operation 343. Press Left/ Right to select User 1 Mode to User 2 Mode.
4. Press Down to highlight Reference Mode.
5. Press Left/ Right to select an picture mode that is closest to your need.
6. Press Down to select a menu item to be changed and adjust the value with Left/
Right. See Fine-tuning the image quality in user modes below for details.
7. When all settings have been done, highlight Save Settings and press Mode/enter to 
store the settings.
8. The confirmation message Setting Saved displays....

Operation 35 1.T1: With the highest color temperature, T1 makes the image appear the most bluish 
white than other settings.
2.T2: Makes images appear bluish white.
3.T3: Maintains normal colorings for white.
4.T4: Makes images appear reddish white.
*About color temperatures:
There are many different shades that are considered to be white for various purposes. One 
of the common methods of representing white color is known as the “color temperature”. A 
white color with a low color temperature appears to...

Operation 36For example, if you select Red and set its value at 0, only the saturation of pure red will 
be affected.
6. Press d to highlight Gain and adjust its values to your preference by pressing eLeft 
orfRight. The contrast level of the primary color you select will be affected. Every 
adjustment made will reflect to the image immediately. 
7. Repeat steps 3 to 6 for other color adjustments.
8. Make sure you have made all of the desired adjustments.
9. Press Menu/exit to exit and save the...

Operation 37 4. Press Down to highlight Timer Position and set the timer 
position by pressing Left/Right
.
Upper left lower left upper right lower right
5. Press Down to highlight Timer Counting Direction and 
select your desired counting direction by pressingLeft/
Right
.
6. Press Down and decide if you want to activate sound reminder by pressing Left/
Right
. If you select Ye s, a double beep sound will be heard at the last 30 seconds of 
counting down/up, and a triple beep sound will be produced when...

Operation 38
Hiding the image
In order to draw the audiences full attention to the 
presenter, you can use BLANK on the projector or 
remote control to hide the screen image. Press any 
button on the projector or remote control to restore the 
image. The word BLANK appears at the lower right 
corner of the screen while the image is hidden. When 
this function is activated with an audio input 
connected, the audio can still be heard. 
You can set the blank time in the 
SYSTEM SETUP: 
Basic > Blank Timer...

Operation 39
Utilizing FAQ function
The Information menu contains possible solutions to problems encountered by users 
regarding image quality, installation, special feature operation and service information.
1. To enter the Information menu, press Left/
 on the projector or remote contorl.
2. Press  Up or Down to select FAQ - Im a ge  
and Installation or FAQ-Features and Service.
3. Press Mode/enter.
4. Press  Up or Down to select the a problem 
and press Mode/enter for possible solutions.
5. Press...

Operation
40
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The 
following settings do not affect the projecti on settings, operation, or performance. 
• Menu Display Time  in the SYSTEM SETUP: Advanced  > Menu Settings  menu sets the 
length of time the OSD will remain active af ter your last button press. The time length 
ranges from 5 to 30 seconds in 5-second increments. Use  Left/Right  to select a 
suitable time.
• Menu Position...