Home > BenQ > Projector > BenQ Mp610 Dlp Users Manual

BenQ Mp610 Dlp Users Manual

    Download as PDF Print this page Share this page

    Have a look at the manual BenQ Mp610 Dlp Users Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 702 BenQ manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Operation 35
    5. Information menu
    This menu shows you the current operating status of the projector.
    Some picture adjustments are available only when certain input sources are in use. 
    Unavailable adjustments are not shown on the screen.
    FUNCTIONDESCRIPTION
    SourceShows the current signal source.
    ResolutionShows the native resolution of the input signal.
    Application 
    ModeShows the selected mode in the   Picture menu.
    Equivalent 
    Lamp HourDisplays the number of hours the lamp has been used.
    SystemShows the Video input system format, NTSC, SECAM or PAL.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Maintenance 36
    Maintenance
    Care of the projector
    Your projector needs little maintenance. The only thing you need to do on a regular basis is 
    to keep the lens clean.
    Never remove any parts of the projector except the lamp. Contact your dealer if other parts 
    need replacing.
    Cleaning the lens
    Clean the lens whenever you notice dirt or dust on the surface. 
    • Use a canister of compressed air to remove dust. 
    • If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens 
    cleaner and gently wipe the lens surface.
    Never rub the lens with abrasive materials.
    Cleaning the projector case
    Before you clean the case, turn the projector off using the proper shutdown procedure as 
    described in Shutdown on page 26 and unplug the power cord.
    • To remove dirt or dust, wipe the case with the supplied cleaning cloth.
    • To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH 
    detergent. Then wipe the case.
    Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the 
    case.
    Storing the projector
    If you need to store the projector for an extended time, please follow the instructions below:
    • Make sure the temperature and humidity of the storage area are within the 
    recommended range for the projector. Please refer to Specifications on page 45 or 
    consult your dealer about the range.
    • Retract the adjuster feet.
    • Remove the batteries from the remote control.
    • Pack the projector in its original packing or equivalent.
    Transporting the projector
    It is recommended that you ship the projector with its original packing or equivalent. When 
    you carry the projector yourself, please use the original box or provided soft carry case.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Maintenance 37
    Lamp information
    Calculation of lamp hour
    When the projector is in operation, the duration (by hours) of lamp usage is automatically 
    calculated by the built-in timer. The method of calculating the equivalent lamp hour is as 
    follows:
    Total (equivalent) lamp hour = hours used in Economic mode + hours used in normal 
    mode
    See Economic Mode (off) on page 34 for more information on Economic mode.
    The lamp hour in Economic mode is calculated as 3/4 of that in normal mode. That is, using 
    the projector in Economic mode helps to extend the lamp hour by 1/4.
    Warning message
    When the Lamp indicator lights up red or a message appears suggesting it is time to replace 
    the lamp, please install a new lamp or consult your dealer. An old lamp may cause a 
    malfunction in the projector and in some instances the lamp may explode.
    For more detailed information on projector warnings, please refer to Indicators on page 
    41.
    The Lamp indicator light and Temperature warning light will light up if the lamp becomes too 
    hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator 
    still lights up after turning the power back on, please contact your dealer.
    The following Lamp warning displays will remind you to change the lamp.
    MessageStatus
    The lamp has been in operation for 2800 hours. 
    Install a new lamp for optimal performance. If the 
    projector is normally run with Economic Mode 
    selected (See Economic Mode (off ) on page 34), 
    you may continue to operate the projector until the 
    2950 hour lamp warning appears.
    The lamp has been in operation for 2950 hour. A 
    new lamp should be fitted to avoid the 
    inconvenience when the projector runs out of lamp 
    time.
    The lamp has been in operation for over 3000 hours. 
    This message will flash in the center of the screen for 
    about 30 seconds together with the Lamp indicator 
    lighting up red for 40 seconds.
    If this warning message displays, the projector will 
    shutdown in 40 seconds. The lamp MUST be 
    replaced before the projector will operate normally.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Maintenance 38
    Replacing the lamp
    • To reduce the risk of electrical shock, always turn the projector off and disconnect the 
    power cord before changing the lamp.   
    • To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes 
    before replacing the lamp.
    • To reduce the risk of injuries to fingers and damage to internal components, use caution 
    when removing lamp glass that has shattered into sharp pieces.
    • To reduce the risk of injuries to fingers and/or compromising image quality by touching 
    the lens, do not touch the empty lamp compartment when the lamp is removed.
    • This lamp contains mercury. Consult your local hazardous waste regulations to dispose 
    of this lamp in a proper manner.
    1. Turn the power off and disconnect the projector from the wall socket. If the lamp is 
    hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.
    2. Turn the projector over. Then loosen the screw 
    on the lamp cover. 
    3. Remove the lamp cover from the projector.
    Do not turn the power on with the lamp cover removed.
    4. Disconnect the lamp connector from the 
    projector.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							
    Maintenance 39
    5. Loosen the screw that secures the lamp.
    6. Pull the lamp from the projector.
    • Pulling it too quickly may cause the lamp to break 
    and scatter broken glass in the projector.
    • Do not place the lamp in locations where water  might splash on it, children can reach it, or near 
    flammable materials.
    • Do not insert your hands into the projector after  the lamp is removed. If you touch the optical 
    components inside, it could cause color 
    unevenness and distortion of the projected 
    images.
    7. As shown in the figure, hold the new lamp and 
    align the two locators on the lamp with the 
    holes on the projector, and then pull the lamp 
    all the way into the projector.
    8. Connect the lamp connector to the projector.
    9. Tighten the screw that secures the lamp.
    • Loose screw may cause a bad connection, which  could result in malfunction.
    • Do not over tighten the screw.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Maintenance 4012. Restart the projector.
    Do not turn the power on with the lamp cover removed. 
    13.Resetting the lamp counter 
    Do not reset if the lamp is not replaced as this could cause 
    damage. 
    i. Press and hold the Exit 5 button on the 
    projector for 5 seconds to display the total used 
    lamp time.
    ii. Press Auto on the projector or on the remote 
    control to reset the lamp hour to “0”.
    iii. Wait about 5 seconds to let the OSD disappear.
    Temperature information
    When the Temperature warning light is on, it is warning you of the following possible 
    problems:
    1. The internal temperature is too high.
    2. The fans are not working.
    Turn the projector off and contact qualified service personnel for further help. For more 
    detailed information, please refer to Indicators on page 41. 10. Replace the lamp cover on the projector.
    11. Tighten the screw that secures the lamp cover.
    • Loose screw may cause a bad connection, which 
    could result in malfunction.
    • Do not over tighten the screw.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Maintenance 41
    Indicators
    Illustration
    •Blank - : Light OFF
    •O : Orange light
    • : Light flashing•R : Red light
    • : Light ON•G : Green light
    LightStatus & Description
    PowerTe m pLamp
    Power events
    --
    Stand-by mode.
    --The Power indicator lig ht is flashing during powering up.
    --The projector is under normal operation.
    --
    1. The projector needs 90 seconds to cool down as it was 
    abnormally shut down without the normal cooling down 
    process. Or
    2. The projector needs to cool for 90 seconds after the 
    power is turned off.
    --The projector has shutdown automatically. If you try to re-start 
    the projector, it w ill shutdow n again. Please contact your dealer 
    for assistance.
    LightStatus & Description
    PowerTe m pLamp
    Lamp events
    -
    The projector has shutdown automatically. If you try to re-start 
    the projector, it w ill shutdow n again. Please contact your dealer 
    for assistance.
    --1. The projector needs 90 seconds to cool down. Or
    2. Please contact your dealer for assistance.
      
      
    O 
     G 
     G 
    O 
    O 
    O  R
     R
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Maintenance 42
    Thermal events
    --
    The projector has shutdown automatically. If you try to re-start 
    the projector, it will shutdown again. Please contact your dealer 
    for assistance.
    -
    -
    -
     R 
     R  R
     R  G
     R  R  R
     G  R  R
    O  R  R
     G  R
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Maintenance 43
    Safety instructions for ceiling mounting of your BenQ
    projector
    We want you to have a pleasant experience using your BenQ projector, so we need to bring 
    this safety matter to your attention to prevent damage to person and property.
    If you intend to mount your projector on the ceiling, we strongly recommend that you use a 
    proper fitting BenQ projector ceiling mount kit and that you ensure it is securely and safely 
    installed.
    If you use a non-BenQ brand projector ceiling mount kit, there is a safety risk that the 
    projector may fall from the ceiling due to an improper attachment through the use of the 
    wrong gauge or length screws.
    You can purchase a BenQ projector ceiling mount kit from the place you purchased your 
    BenQ projector. BenQ recommends that you also purchase a separate Kensington lock 
    compatible security cable and attach it securely to both the Kensington lock slot on the 
    projector and the base of the ceiling mount bracket. This will perform the secondary role of 
    restraining the projector should its attachment to the mounting bracket become loose.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Troubleshooting 44
    Troubleshooting
    THE PROJECTOR DOES NOT TURN ON.
    NO PICTURE
    BLURRED IMAGE
    REMOTE CONTROL DOES NOT WORK
    CauseRemedy
    There is no power from the power 
    cable.Plug the power cord into the AC inlet on the 
    projector, and plug the power cord into the 
    power outlet. If the power outlet has a switch, 
    make sure that it is switched on.
    Attempting to turn the projector on 
    again during the cooling process.Wait until the cooling down process has 
    completed.
    CauseRemedy
    The video source is not turned on or 
    connected correctly.Turn the video source on and check that the 
    signal cable is connected correctly.
    The projector is not correctly 
    connected to the input source device.Check the connection.
    The input signal has not been 
    correctly selected.Select the correct input signal with the Source 
    key on the projector or remote control.
    The lens cap is still attached to the 
    lens.Remove the lens cap.
    CauseRemedy
    The projection lens is not correctly 
    focused.Adjust the focus of the lens using the focus 
    ring.
    The projector and the screen are not 
    aligned properly.Adjust the projection angle and direction as 
    well as the height of the unit if necessary.
    The lens cap is still attached to the 
    lens.Remove the lens cap.
    CauseRemedy
    The battery is out of power. Replace the battery with a new one.
    There is an obstacle between the 
    remote control and the projector.Remove the obstacle.
    You are too far away from the 
    projector.Stand within 6 meters (19.5 feet) of the 
    projector.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    All BenQ manuals Comments (0)

    Related Manuals for BenQ Mp610 Dlp Users Manual