BenQ Fp93es User Manual
Have a look at the manual BenQ Fp93es User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 702 BenQ manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
31 How to adjust your monitor H. Position Adjusts the horizontal position of the OSD menu. Press the W or X keys to adjust the value.0 to 100 V. Position Adjusts the vertical position of the OSD menu.0 to 100 Display Time Adjusts the display time of the OSD menu.• 5 sec. • 10 sec. • 15 sec. • 20 sec. • 25 sec. • 30 sec. OSD Lock Prevents all the monitor settings from being accidentally changed. When this function is activated, the OSD controls and hotkey operations will be disabled.Press the W or X keys to adjust the value. To unlock the OSD controls when the OSD is preset to be locked, press and hold the MENU button for 15 seconds to enter the OSD Lock option and make changes. Alternatively, you may use the W or X keys to select ’OFF’ in the OSD Lock submenu from the ’OSD Settings’ menu, and all OSD controls will be accessible. • ON • OFF Press MENU to leave the OSD Settings menu. Information Displays the current monitor property settings.Press the ENTER key to select this option. Reset All Resets all mode, color and geometry settings to the factory default values.Press the W or X keys to adjust the value.• YES • NO
32 Troubleshooting 9. Troubleshooting Frequently asked questions (FAQ) The image is blurred: Read the How to adjust the screen resolution on page 16 section, and then select the correct resolution, refresh rate and make adjustments based on these instructions. How do you use a VGA extension cable? Remove the extension cable for the test. Is the image now in focus? If not, optimize the image by working through the instructions in the How to adjust the screen refresh rate on page 17 section It is normal for blurring to occur due to conduction losses in extension cables. You can minimize these losses by using an extension cable with better conduction quality or with a built-in booster. Does the blurring only occur at resolutions lower than the native (maximum) resolution? Read the How to adjust the screen resolution on page 16 section. Select the native resolution. Pixel errors can be seen: One of several pixels is permanently black, one or more pixels are permanently white, one or more pixels are permanently red, green, blue or another color. • Clean the LCD screen. • Cycle power on-off. • These are pixels that are permanently on or off and is a natural defect that occurs in LCD technology. The image has a faulty coloration: It has a yellow, blue or pink appearance. Select MENU > PICTURE > Color > Reset Color, and then choose “YES” in the “Caution” message box to reset the color settings to the factory defaults. If the image is still not correct and the OSD also has faulty coloration, this means one of the three primary colors is missing in the signal input. Now check the signal cable connectors. If any pin is bent or broken off, please contact your dealer to get necessary support. No image can be seen: Is the prompt on the display illuminated in green? If the LED is illuminated in green and there is a message “Out of Range” on the screen, this means you are using a display mode that this monitor does not support, please change the setting to one of the supported mode. Please read “ Supported PC Timings on page 34” section. Faint shadow from the static image displayed is visible on the screen: •Activate the power management function to let your computer and monitor go into a low power sleep mode when not actively in use. •Use a screensaver to prevent the occurrence of image retention. Is the prompt on the display illuminated in orange?
33 Troubleshooting If the LED is illuminated in orange, the power management mode is active. Press any button on the computer keyboard or move the mouse. If that does not help, check the signal cable connectors. If any pin is bent or broken off, please contact your dealer to get necessary support. Is the prompt on the display not illuminated at all? Check the power supply mains socket, the external power supply and the mains switch. The image is distorted, flashes or flickers: Read the How to adjust the screen resolution on page 16 section and then select the correct resolution, refresh rate and make adjustments based on these instructions. The image is displaced in one direction: Read the How to adjust the screen resolution on page 16 section and then select the correct resolution, refresh rate and make adjustments based on these instructions. The OSD controls are inaccessible: •To unlock the OSD controls when the OSD is preset to be locked, press and hold the “MENU” key for 15 seconds to enter the “OSD Lock” option and make changes. •Alternatively, you may use the W or Xkeys to select “OFF” in the “OSD Lock” submenu from the “OSD Settings” menu (under SYSTEM), and all OSD controls will be accessible. Need more help? If your problems remain after checking this manual, please contact your place of purchase or e-mail us at: [email protected]
34 Supported PC Timings 10. Supported PC Timings •Modes not listed in the table may not be supported. For an optimal picture, we recommended you choose a mode listed in the table above. •There are 22 available modes that are compatible with Windows. •Image disruption may occur as a result of signal frequency differences from graphic cards which do not correspond with the usual standard. This is not, however, an error. You may improve this situation by altering an automatic setting or by manually changing the phase setting and the pixel frequency from the “DISPLAY” menu. •If you switch off the monitor, interference lines can occur on your screen. But do not be concerned about this, as it is normal. •To extend the service life of the product, we recommend that you use your computers power management function. Incoming display mode (Input timing) ResolutionHorizontal Frequency (KHz)Ve rt ic a l Frequency (Hz)Pixel Frequency (MHz)Comment 640 x 350 31.47(P) 70.08(N) 25.17 DOS 720 x 400 31.47(N) 70.08(P) 28.32 DOS 640 x 480 31.47(N) 60.00(N) 25.18 DOS 640 x 480 35.00(N) 67.00(N) 30.24 Macintosh 640 x 480 37.86(N) 72.80(N) 31.50 VESA 640 x 480 37.50(N) 75.00(N) 31.50 VESA 800 x 600 35.16(P) 56.25(P) 36.00 VESA 800 x 600 37.88(P) 60.32(P) 40.00 VESA 800 x 600 48.08(P) 72.19(P) 50.00 VESA 800 x 600 46.87(P) 75.00(P) 49.50 VESA 832 x 624 49.72(N) 74.55(N) 57.29 Macintosh 1024 x 768 48.36(N) 60.00(N) 65.00 VESA 1024 x 768 56.48(N) 70.10(N) 75.00 VESA 1024 x 768 60.02(P) 75.00(P) 78.75 VESA 1152 x 864 67.50(P) 75.00(P) 108.00 VESA 1152 x 870 68.68(N) 75.06(N) 100.00 Macintosh 1152 x 900 61.80(N) 66.00(N) 94.50 SUN 66 1152 x 900 71.81(N) 76.14(N) 108.00 SUN 1280 x 1024 64.00(P) 60.00(P) 108.00 VESA 1280 x 1024 75.83(N) 71.53(N) 128.00 IBMI 1280 x 1024 80.00(P) 75.00(P) 135.00 VESA 1280 x 1024 81.18(N) 76.16(N) 135.09 SPARC2
35 Specifications 11. Specifications BenQ FP73E S ModelFP73E S Display type Viewable diagonal Native (maximum) resolution Colors Contrast / Brightness Response time Viewing angle (left/right, up/down) 17.0”, active, TFT 432 mm 1,280 x 1,024 16.7 million 800:1 / 300 cd/m 2 5 ms 160, 160 (CR> 10) 170, 170 (CR> 5) Line frequency Image frequency31 - 83 kHz Multi- frequency monitor 56 - 76 Hz modes within these parameters Image diagnostics Controls FunctionsDigital, OSD Technology, i key (automatic image setting) 5 buttons and i key. Contrast, brightness, vert. & hor. image position, phase, pixel clock, color balance, color palette, multiple-language OSD, OSD position, input selection, picture mode, Senseye demo Power management Max. power consumption Standby power consumptionVESA DPMS, EPA 45 Watt < 1 Watt Input signal PC Speaker SynchronizationRGB analog 0.7 Vpp/75 Ohm positive Digital: DVI-D (optional) 1 W x 2 TTL separate signal connection 15-pin mini D-sub cable Temperature (operating) Air humidity (operating)0 °C - 40 °C 10% - 90% Certifications TCO 03, TÜV/Ergonomics, TÜV/ GS, FCC Class B, ISO 13406-2, VCCI, CB Report, CE, C-Tick, BSMI, Fimko, GOST, CSA, CCC, eK
36 Specifications Operating voltage Tilt (down/up) Swivel (left/right) Height adjustment Dimensions (H x W x D) WeightAutomatic switched mode power supply, 100-240 V, 50-60 Hz -5° ~ +20 ° 180°/180° 72 mm 416.1 x 371.6 x 222 mm 6.2 kg
37 Specifications BenQ FP93E S ModelFP93E S Display type Viewable diagonal Native (maximum) resolution Colors Contrast / Brightness Response time Viewing angle (left/right, up/down) 19.0”, active, TFT 480 mm 1,280 x 1,024 16.7 million 800:1 / 300 cd/m 2 5 ms 160, 160 (CR> 10) Line frequency Image frequency31 - 83 kHz Multi- frequency monitor 56 - 76 Hz modes within these parameters Image diagnostics Controls FunctionsDigital, OSD Technology, i key (automatic image setting) 5 buttons and i key. Contrast, brightness, vert. & hor. image position, phase, pixel clock, color balance, color palette, multiple-language OSD, OSD position, input selection, picture mode, Senseye demo Power management Max. power consumption Standby power consumptionVESA DPMS, EPA 50 Watt < 1 Watt Input signal PC Speaker SynchronizationRGB analog 0.7 Vpp/75 Ohm positive Digital: DVI-D (optional) 1 W x 2 TTL separate signal connection 15-pin mini D-sub cable Temperature (operating) Air humidity (operating)0 °C - 40 °C 10% - 90% Certifications TCO 03, TÜV/Ergonomics, TÜV/ GS, FCC Class B, ISO 13406-2, VCCI, CB Report, CE, C-Tick, BSMI, Fimko, GOST, CSA, CCC, eK
38 Specifications Operating voltage Tilt (down/up) Swivel (left/right) Height adjustment Dimensions (H x W x D) WeightAutomatic switched mode power supply, 100-240 V, 50-60 Hz -5° ~ +20 ° 180°/180° 60 mm 429 x 409.2 x 222 mm 6.76 kg