BenQ Fp73g User Manual

							
  31
  How to adjust your monitor
 
Miscellaneous sub-menu
Input Select:
Press the 
W or X keys to select D-sub (analog) 
or DVI (digital) input to activate the new 
settings.
Press the  Exit key to return to previous menu.
 
Sharpness:
Press the 
W or X keys to adjust the degree of 
Sharpness .
Press the  Exit key to return to previous menu.
 
Display Information:
Select  Display Information  to display the 
current monitor property settings. 
Press the  Exit key to return to previous menu.
 
 
						

							
32 Troubleshooting  
Troubleshooting
Frequently asked questions (FAQ)
The image is blurred:
Read the How to adjust the screen resolution on page 20  section, and then select the correct 
resolution, refresh rate and make adjustments based on these instructions.
How do you use a VGA extension cable?
Remove the extension cable for the test. Is the im age now in focus? If not, optimize the image by 
working through the instructions in the 
How to adjust the screen refresh rate on page 21 section It 
is normal for blurring to occur due to conduc tion losses in extension cables. You can minimize 
these losses by using an extension cable with better co nduction quality or with a built-in booster.
Does the blurring only occur at resolutions lower than the native (maximum) resolution?
Read the How to adjust the screen resolution on page 20 section. Select the native resolution.
Pixel errors can be seen:
One of several pixels is permanently black, one or  more pixels are permanently white, one or more 
pixels are permanently red, green, blue or another color.
•   Clean the LCD screen.
•   Cycle power on-off.
•   These are pixels that are permanently on or  off and is a natural defect that occurs in LCD 
technology.
The image has a faulty coloration:
It has a yellow, blue or pink appearance.
On the monitor, press “Enter” key and press W or X key to move to the “Recall” icon and press 
“Enter” key to enter “Recall” sub menu. Press 
W or X key to select “Color Re call” and select “Yes” 
in “Color Recall” sub menu, then press “Enter” key to  recall to factory settings. If the image is still 
not correct and the OSD also has faulty coloration , this means one of the three primary colors is 
missing in the signal input. Now check the signal ca ble connectors. If any pin is bent or broken off, 
please contact your dealer  to get necessary support.
No image can be seen:
Is the prompt on the disp lay illuminated in green?
If the LED is illuminated in green and there is a  message “Out of Range” on the screen, this means 
you are using a display mode that this monitor  does not support, please change the setting to one 
of the supported mode. Please read “
Supported opearting modes on page 34” section.
Is the prompt on the display illuminated in orange?
If the LED is illuminated in orange, the power management mode is active. Press any button on 
the computer keyboard or move the mouse. If that does not help, check the signal cable 
connectors. If any pin is bent or broken off, plea se contact your dealer to get necessary support.
Is the prompt on the display not illuminated at all?
Check the power supply mains socket, the external power supply and the mains switch.
11
19
 
						

							
  33
  Troubleshooting
The image is distorted, flashes or flickers:
Read the  How to adjust the screen resolution on page 20  section and then select the correct 
resolution, refresh rate and make adjustments based on these instructions.
The image is displaced in one direction:
Read the  How to adjust the screen resolution on page 20  section and then select the correct 
resolution, refresh rate and make adjustments based on these instructions.
Need more help?
If your problems remain after checking this ma nual, please contact your place of purchase or 
e-mail us at: [email protected]
 
						

							
34  Supported opearting modes  
Supported opearting modes
•Modes not listed in the table may not be supporte d. For an optimal picture, we recommended you 
choose a mode listed in the table above.
• There are 22 available modes that are compatible with Windows. 
• Image disruption may occur as a result of signal  frequency differences from graphic cards which 
do not correspond with the usual standard. This is not, however, an error. You may improve this 
situation by altering an automatic setting or by  manually changing the phase setting and the pixel 
frequency from the “Geometry” menu.
• If you switch off the monitor, interference lines  can occur on your screen. But do not be concerned 
about this, as it is normal. 
• To extend the service life of the product, we recommend that you use your computers power 
management function. 
11
110
Incoming display mode (Input timing)
ResolutionHorizontal 
Frequency (KHz)Ve r t i c a l  
Frequency (Hz)Pixel 
Frequency (MHz)Comment
640x350 31.47(P) 70.08(N) 25.17 DOS
720x400 31.47(N) 70.08(P) 28.32 DOS
640x480 31.47(N) 60.00(N) 25.18 DOS
640x480 35.00(N) 67.00( N) 30.24 Macintosh
640x480 37.86(N) 72.80(N) 31.50 VESA
640x480 37.50(N) 75.00(N) 31.50 VESA
800x600 35.16(P) 56.25(P) 36.00 VESA
800x600 37.88(P) 60.32(P) 40.00 VESA
800x600 48.08(P) 72.19(P) 50.00 VESA
800x600 46.87(P) 75.00(P) 49.50 VESA
832x624 49.72(N) 74.55( N) 57.29 Macintosh
1024x768 48.36(N) 60.00(N) 65.00 VESA
1024x768 56.48(N) 70.10(N) 75.00 VESA
1024x768 60.02(P) 75.00(P) 78.75 VESA
1152x864 67.50(P) 75.00(P) 108.00 VESA
1152x870 68.68(N) 75.06(N) 100.00 Macintosh
1152x900 61.80(N) 66.00(N) 94.50 SUN 66
1152x900 71.81(N) 76.14(N) 108.00 SUN
1280x1024 64.00(P) 60.00(P) 108.00 VESA
1280x1024 75.83(N) 71.53(N) 128.00 IBMI
1280x1024 80.00(P) 75.00(P) 135.00 VESA
1280x1024 81.18(N) 76.16(N) 135.09 SPARC2
 
						

							
  35
  Specifications
Specifications
BenQ FP73G
1 1
111
ModelFP73G
Display type 
Viewable diagonal 
Native (maximum) resolution
Colors
Contrast / Brightness
Response time 
Viewing angle (left/right, up/down)  17.0
”, active, TFT
432 mm
1,280 x 1,024
16.2 million
700:1 / 300 cd/m
2
6 ms 
150, 140 (CR=10)
170, 170 (CR=5)
Line frequency 
Image frequency 30 - 82 kHz Multi-
 frequency monitor
56 - 76 Hz modes within these parameters
Image diagnostics 
Controls 
Functions Digital, OSD Technology,
 iKey  (automatic image 
setting)  
5 buttons and  iKey.
Contrast, brightness, vert . & hor. image position, 
phase, pixel clock, color  balance, color palette, 
multiple-language OSD, OS D position, status 
indicator, input selection
Power management
Max. power consumption 
Standby power consumption VESA DPMS, EPA
40 Watt
<
 1 Watt, 120 V
<
 2 Watt, 240 V
Input signal 
Synchronization RGB analog 0.7 Vpp/
75 Ohm positive 
Digital: DVI-D (optional)
TTL separate signal connection 15-pin mini D-sub 
cable  
Temperature (operating) 
Air humidity (operating) 0 °C - 40 °C
10% - 90%
Certifications TCO 03, TÜV/Er gonomics, TÜV/ GS, FCC Class 
B, ISO 13406-2, VCCI, CB  Report, CE, C-Tick, 
BSMI, Fimko, GOST, CSA, CCC
 
						

							36 Specifications  
Operating voltage 
Dimensions (H x W x D) 
WeightAutomatic switched mode power supply, 
90-264 V, 47-63 Hz
363.8 x 356.5 x 135 mm
3.7 kg