BenQ Fp202wa User Manual

							  11   How to assemble your monitor hardware
How to detach the stand base
1. Prepare the monitor and area.
Turn off the monitor and the power before unplugging the 
power cable. Turn off the computer before unplugging the 
monitor signal cable.
Please be careful to prevent damage to the monitor. 
Placing the screen surface on an object like a stapler or a 
mouse will crack the glass or damage the LCD substrate 
voiding your warranty. Sliding or scraping the monitor 
around on your desk will scratch or damage the monitor 
surround and controls. 
Protect the monitor and screen by clearing a flat open area 
on your desk and placing a soft item like a towel on the 
desk for padding, before laying the screen face down on a 
flat clean padded surface.
2. Release the locking clip on one side of the stand base 
while pulling the edge of the base away from the 
stand arm.
3. Release the other locking clip to detach the stand base 
from the monitor stand arm.
 
						

							12  Getting the most from your BenQ monitor  
4. Getting the most from your BenQ monitor
To gain the most benefit from your new BenQ color LCD flat screen monitor, you should install 
the custom BenQ LCD Monitor driver software as provided on the BenQ LCD Monitor CD-ROM.
The circumstances under which you connect and install your BenQ LCD Monitor will determine 
which process you need to follow to successfully install the BenQ LCD Monitor driver software. 
These circumstances relate to which version of Microsoft Windows you are using, and whether 
you are connecting the monitor and installing the software onto a new computer (without existing 
monitor driver software), or whether you are upgrading an existing installation (which already has 
existing monitor driver software) with a newer monitor. 
In either case however, the very next time you turn on your computer (after connecting the 
monitor to your computer), Windows will automatically recognise the new (or different) 
hardware, and will launch its Found New Hardware wizard. 
Follow the wizard instructions until it asks you to select a monitor model. At that point, click the 
Have Disk button, insert the BenQ LCD Monitor CD-ROM and select the appropriate monitor 
model. Further details and step-by-step instructions for both an automatic (new) or upgrade 
(existing) installation follow. See:
•To install the monitor on a new computer on page 13. 
•To upgrade the monitor on an existing computer on page 14 
If you require a User Name and Password to login to your Windows computer, you must be logged on as 
an Administrator or as a member of the Administrators group in order to install the monitor driver software. 
Furthermore, if your computer is connected to a network which has security access requirements, network 
policy settings may prevent you from installing software on your computer. 
 
						

							  13   Getting the most from your BenQ monitor
To install the monitor on a new computer
This instruction details the procedure for selecting and installing the BenQ LCD Monitor driver 
software on a new computer which has never had a monitor driver installed before. This 
instruction is only suitable for a computer which has never been used before, and for which the 
BenQ LCD Monitor is the first ever monitor to be connected to it.
If you are adding the BenQ LCD Monitor to an existing computer that has already had another monitor 
connected to it (and has monitor driver software installed), you should not be following these instructions. 
You should instead be following the instructions for To upgrade the monitor on an existing computer 
on page 14.
1. Follow the instructions in How to assemble your monitor hardware on page 8. 
When Windows starts, it will automatically detect the new monitor and launch the Found New Hard-
ware Wizard. Follow the prompts until it displays the option to Install Hardware Device drivers.
2. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
3. Check Search for a suitable driver for my device option, and click Next.
4. Check the option for CD-ROM drives (uncheck all others) and click Next.
5. Look to confirm that the wizard has selected the correct name of your monitor as “BenQ 
FP202W/FP202WA” and click Next.
6. Click Finish.
7. Restart the computer.
 
						

							14  Getting the most from your BenQ monitor  
To upgrade the monitor on an existing computer
This instruction details the procedure for manually updating the existing monitor driver software 
on your Microsoft Windows computer. It is currently tested as compatible (and recommended 
only) for Windows XP and Windows Vista Operating System (OS). 
The BenQ LCD Monitor driver for your model may well function perfectly with other versions of 
Windows, however, as at the time of writing, BenQ has done no testing of this driver on other versions of 
Windows and cannot guarantee its operation on those systems.
Installing monitor driver software involves selecting an appropriate information file (.inf ) on the 
BenQ LCD Monitor CD-ROM for the particular model monitor you have connected, and letting 
Windows install the corresponding driver files from the CD. You need only steer it in the right 
direction. Windows has an Upgrade Device Driver Wizard to automate the task and guide you 
through the file selection and installation process. 
See:
•How to install on Windows Vista system on page 15.
•How to install on Windows XP system on page 16.
 
						

							  15   Getting the most from your BenQ monitor
How to install on Windows Vista system
1. Open Display Settings.
Right-click the desktop and select Personalize from the popup menu.
Select Display Settings from the Personalize appearance and sounds window. 
The Display Settings window will display.
2. Click the Advanced Settings button. 
The Generic PnP Monitor Properties window will display.
3. Click the Monitor tab and the Properties button.
4. Click Continue in the prompted User Account Control window.
5. Click the Driver tab and the Update Driver button.
6. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
7. In the Update Driver Software window, select the option ‘Browse my computer for driver 
software’.
8. Click ‘Browse’ and select Driver > Windows Vista > FP202W/FP202WA from the CD, and 
click the Next button.
This will copy and install the appropriate monitor driver files to your computer.
9. Click Close.
You do not need to restart Windows Vista, as the BenQ LCD monitor drivers will operate immediately 
with no further action required by you. 
 
						

							16  Getting the most from your BenQ monitor  
How to install on Windows XP system
1. Open Display Properties.
The quickest shortcut to Display Properties is through the Windows desktop. 
Right-click the desktop and select Properties from the popup menu.
Alternatively, the Windows menu to Display Properties is located in Control Panel. 
In Windows XP version, Control Panel is located directly under the main Start menu item. 
The menu options displayed will depend upon which type of view is selected for your system. 
•Under the Classic view, click Start | Control Panel | Display.
•Under the Category view, click Start | Control Panel | Appearance and Themes | Change the 
screen resolution.
The Display Properties window will display.
2. Click the Settings tab and the Advanced button. 
The Advanced Display Properties window will display.
3. Click the Monitor tab and select the ‘Plug and Play Monitor’ from the list.
If there is only one monitor in the list, it will already be selected for you.
4. Click the Properties button. 
The Monitor Properties window will display. 
If the driver provider is listed as BenQ, and the model matches that of your new monitor, the proper 
drivers are already installed, and you need do nothing further. Cancel out of these property windows.
However, if BenQ is not listed as the manufacturer, or the correct model is not currently shown, you 
will need to continue with these instructions.
5. Click the Driver tab and the Update Driver button.
The Hardware Update Wizard will display. Follow the wizard instructions noting the steps below:
6. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
7. Check the option ‘Install from a list or specific location’ and click Next.
8. Check the option ‘Search for the best driver in these locations’ and also check ‘Search 
removable media’, then click Next.
Please wait while the wizard searches for drives and the BenQ LCD Monitor CD inserted in step 6. 
When completes, the wizard should have found and selected the BenQ driver on the CD appropriate to 
your monitor model, in this case ‘BenQ FP202W/FP202WA’ in the location ‘d:\Driver\Windows 
XP\FP202W/FP202WA\BenQFP202W.inf/BenQFP202WA.inf ’ or similar. 
The drive letter for your CD drive may differ from the example above depending upon your system – it 
may be ‘D:’ or ‘E:’ or ‘F:’ etc.
9. Select (single-click) the file named ‘BenQ FP202W/FP202WA’ on the CD, and click the Next 
button.
This will copy and install the appropriate monitor driver files to your computer.
10. Click Finish.
This will close the wizard and return you to the Monitor Properties window, now renamed BenQ 
FP202W/FP202WA Properties.
11. Click Close, OK, and OK.
This will close the Display Properties windows. You do not need to restart Windows XP, as the BenQ 
LCD monitor drivers will operate immediately with no further action required by you. 
 
						

							  17   How to adjust the screen resolution
5.  How to adjust the screen resolution
Due to the nature of liquid crystal display (LCD) technology, the picture resolution is always fixed. 
The best possible picture for your FP202W V3/FP202W A is achieved with a resolution of 
1680 x 1050. This is called “Native Resolution” or maximal resolution – that is, the clearest picture. 
Lower resolutions are displayed on a full screen through an interpolation circuit. Image blurring 
across pixel boundaries can occur with the interpolated resolution depending upon the image type 
and its initial resolution.
To take full advantage of LCD technology you should select the native resolution setting of 1680 x 1050 
on your PC screen resolution setting as described below. Be aware that not all PC video cards provide 
this resolution value. If your doesnt, check with the video card manufacturers website for an updated 
driver for your particular model PC video card which supports this resolution. Software video drivers are 
often updated and available for new hardware video resolutions. If necessary, you may need to replace 
and update the PC video card hardware to be able to support the native resolution of the monitor.
1. Open Display Properties and select the Settings tab. 
Yo u  c a n  o p e n  Display Properties by right-clicking on the Windows desktop and selecting Properties 
from the pop-up menu.
2. Use the slider in the ‘Screen area’ section to adjust the screen resolution.
Select the recommended resolution of 1680 x 1050 then click Apply.
If you select some other resolution, be aware that this other resolution is interpolated and may not 
accurately display the screen image as well as it could do at the native resolution setting.
3. Click OK then Ye s. 
4. Close the Display Properties window.
 
						

							18  How to adjust the screen refresh rate  
6. How to adjust the screen refresh rate 
You don’t have to choose the highest possible refresh rate on an LCD display, because it is not 
technically possible for an LCD display to flicker. The best results are obtained by using the factory 
modes already set in your computer. There is a table with the factory modes in the specification 
section of this Users Manual: 
Supported PC Timings on page 34
You can choose 60 Hertz for the native resolution of 1680 x 1050. 
1. Double click the Display icon in Control Panel.
2. From the Display Properties window, select the Settings tab and click the Advanced button. 
3. Select the Adapter tab, and select an appropriate refresh rate to match one of the applicable 
factory modes as listed in the specification table.
4. Click Change, OK, then Ye s. 
5. Close the Display Properties window.
 
						

							  19   Picture optimization
7. Picture optimization 
The easiest way to obtain an optimal display from an analog (D-Sub) input is to use the i key 
function. Press the 
i key to optimize the currently displayed image to the screen. 
When you connect a digital video output using a digital (DVI) cable to your monitor, the i key and the Auto 
Adjustment function will be disabled, because the monitor will automatically display the best image. 
Please ensure that the connected graphic card on your computer is set to the native resolution of the 
monitor (1680 x 1050) when you use the i key function.
If you wish, you can always adjust the screen geometric settings manually using geometry menu 
items. To assist you in this endeavour, BenQ has provided a screen test image utility which you can 
use to check for screen color, grayscale and line gradient display.
1. Run the test program auto.exe from CD-ROM. You could also use any other image, such as 
the desktop of your operating system. However, we recommend that you use auto.exe. As you 
run auto.exe, a test pattern displays.
2. Press the 
i key on the monitor.
3. Press the Exit key to access the monitor On-Screen Display (OSD) menu.
4. Use the 
t or u keys to select DISPLAY and press the ENTER key to enter the menu.
5. If you notice a vertical noise (like a curtain effect-shimmering of vertical lines), press the 
t 
or 
u keys to select Pixel Clock and press the ENTER key. Then press the t or u keys to 
adjust the monitor until the noise disappears.
6. If you notice a horizontal noise, press the 
t or u keys to select Phase and press the ENTER 
key. Then press the 
t or u keys adjust the monitor until the noise disappears.
 
						

							20  How to adjust your monitor  
8. How to adjust your monitor
The control panel
1. “Power”: Turn the power on or off.
2. “ENTER” key: Enter sub menus and select items.
3.
t (Up) key: For Up/Increase adjustment. The key is also the hot key for Brightness.
4.
u (Down) key: For Down/Decrease adjustment.  The key is also the hot key for Contrast.
5. “Exit” key: Activate OSD main menu and return to the previous menu or exit OSD.
6. “Mode” key: Switch between different modes, including Standard, Movie, Dynamics, Photo, and 
sRGB.
7. “Input” key: Manually switch the input signal between D-Sub and DVI. (Not available for 
FP202W A)
8. “
i key” : Adjust vertical position, phase, horizontal position and pixel clock automatically.
OSD = On Screen Display.
The hot-keys will display a graduated scale for adjusting the value of that setting, and will only operate 
while the OSD menu is not currently displaying. Hot-key displays will disappear after a few seconds of no 
key activity. See Hot key mode on page 21.
1
2
3
4
5
6
7
8