BenQ Bl2710pt User Manual

  11   How to assemble your monitor hardware
How to assemble your monitor hardware
 • If the computer is turned on you must turn it off before continuing. 
Do not plug-in or turn-on the power to the monitor until instructed to do so.
• The following illustrations are for your reference only. Available input and output jacks may vary depending on 
the purchased model.
1. Attach the monitor base.
Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a...

12  How to assemble your monitor hardware  
Tighten the thumbscrew on the bottom of the monitor 
base as illustrated.
Orient and align the stand arm with the monitor ( ), 
push them together until they click and lock into place 
().
Gently attempt to pull them back apart to check that 
they have properly engaged.
Carefully lift the monitor, turn it over and place it 
upright on its stand on a flat even surface.
You should position the monitor and angle the screen to 
minimize unwanted reflections from...

  13   How to assemble your monitor hardware
To Connect the DVI-D Cable
Connect the plug of the DVI-D cable (at the end 
without the ferrite filter) to the monitor video socket. 
Connect the other end of the cable (at the end with the 
ferrite filter) to the computer video socket.
Tighten all finger screws to prevent the plugs from 
accidently falling out during use.
Or
To Connect the HDMI Cable
Connect the plug of the HDMI cable to the HDMI port 
on the monitor. Connect the other end of the cable to...

14  How to assemble your monitor hardware  
4. Connect USB devices.
Connect the USB cable between the PC and the 
monitor (via the upstream USB port at the back). This 
upstream USB port transmits data between the PC and 
the USB devices connected to the monitor.
Connect USB devices via other USB ports 
(downstream) on the monitor. These downstream USB 
ports transmit data between connected USB devices 
and the upstream port.
Or (BL2710)
5. Connect the power cable to the monitor.
Plug one end of the...

  15   How to assemble your monitor hardware
6. Organize the cables.
7. Install the headphone hook (optional step).
You can install the headphone hook to place your 
headphone. It is useful when your headphone is not in 
use.
Orient and align the headphone hook with the hole on 
the monitor stand, and attach the hook to the hole 
().
Turn the hook clockwise until you cannot go further 
( ). The headphone hook is ready to use.
The maximum load capacity of the headphone hook is 500g.
8. Connect-to and...

16  How to assemble your monitor hardware  
How to detach the stand and the base
1. Prepare the monitor and area.
Turn off the monitor and the power before unplugging 
the power cable. Turn off the computer before 
unplugging the monitor signal cable.
Protect the monitor and screen by clearing a flat open 
area on your desk and placing a soft item like a towel on 
the desk for padding, before laying the screen face down 
on a flat clean padded surface.
Please be careful to prevent damage to the monitor....

  17   How to assemble your monitor hardware
Turn the stand counterclockwise until you cannot go 
further.
And then detach the base from the stand.
You can remove the headphone hook as illustrated. Keep the 
headphone hook somewhere safe.
 

18  How to assemble your monitor hardware  
Adjusting the monitor height
To adjust the monitor height, hold both the left and the 
right sides of the monitor to lower the monitor or lift 
it up to the desired height.
• Avoid placing hands on the upper or lower part of the 
height-adjustable stand or at the bottom of the monitor, as 
ascending or descending monitor might cause personal 
injuries. Keep children out of reach of the monitor while 
performing this operation.
• If the monitor has been rotated...

  19   How to assemble your monitor hardware
Rotating the monitor
1. Pivot the display.
Before rotating the monitor with a portrait viewing orientation, the display has to be rotated 90 
degrees.
Click to launch the 
Display Pilot Software (if installed from the CD), and check Auto Pivot to 
set the display to rotate with the monitor automatically.
Alternatively, right-click the desktop and select 
Screen resolution from the popup menu. Select 
Portrait in Orientation, and apply the setting.
Depending on...

20  How to assemble your monitor hardware  
Viewing angle adjustment
You may position the screen to the desired angle with -5° to + 20° monitor tilt, 90° (left and 
right total) monitor swivel, and 150 mm monitor height.
4. Rotate the monitor 90 degrees clockwise as 
illustrated.
To avoid the edge of the LCD display hitting the monitor base 
surface while it is being rotated, do tilt and extend the monitor 
to the highest position before you start to rotate the display. You 
should also make sure there...