BenQ Bl2410pt User Manual

  11   How to assemble your monitor hardware
Tighten the thumbscrew on the bottom of the monitor 
base as illustrated.
Orient and align the stand arm with the monitor ( ), 
push them together until they click and lock into place 
().
Gently attempt to pull them back apart to check that 
they have properly engaged.
Carefully lift the monitor, turn it over and place it 
upright on its stand on a flat even surface.
You should position the monitor and angle the screen to 
minimize unwanted reflections from...

12  How to assemble your monitor hardware  
To Connect the DVI-D Cable
Connect the plug of the DVI-D cable (at the end 
without the ferrite filter) to the monitor video socket. 
Connect the other end of the cable (at the end with the 
ferrite filter) to the computer video socket.
Tighten all finger screws to prevent the plugs from 
accidently falling out during use.
To Connect the DP Cable
Connect the plug of the DP cable to the monitor video 
socket. Connect the other end of the cable to the 
computer...

  13   How to assemble your monitor hardware
Connect USB devices via other USB ports 
(downstream) on the monitor. These downstream USB 
ports transmit data between connected USB devices 
and the upstream port.
See picture on the right.
5. Connect the power cable to the monitor.
Plug one end of the power cord into the socket labelled 
 on the rear of the monitor. Do not connect the 
other end to a power outlet just yet.
6. Organize the cables.
7. Connect-to and turn-on the power.
Plug the other end of...

14  How to assemble your monitor hardware  
Turn on the monitor by pressing the power button on 
the monitor. 
Turn on the computer too, and follow the instructions 
in Getting the most from your BenQ monitor on page 
21 to install the monitor software.
To extend the service life of the product, we recommend 
that you use your computers power management function.
 

  15   How to assemble your monitor hardware
How to detach the stand and the base
1. Prepare the monitor and area.
Turn off the monitor and the power before unplugging 
the power cable. Turn off the computer before 
unplugging the monitor signal cable.
Protect the monitor and screen by clearing a flat open 
area on your desk and placing a soft item like a towel on 
the desk for padding, before laying the screen face down 
on a flat clean padded surface.
Please be careful to prevent damage to the monitor....

16  How to assemble your monitor hardware  
Turn the stand counterclockwise until you cannot go 
further.
And then detach the base from the stand.
 

  17   How to assemble your monitor hardware
Adjusting the monitor height
To adjust the monitor height, hold both the left and the 
right sides of the monitor to lower the monitor or lift 
it up to the desired height.
• Avoid placing hands on the upper or lower part of the 
height-adjustable stand or at the bottom of the monitor, as 
ascending or descending monitor might cause personal 
injuries. Keep children out of reach of the monitor while 
performing this operation.
• If the monitor has been rotated...

18  How to assemble your monitor hardware  
Rotating the monitor
1. Pivot the display.
Before rotating the monitor with a portrait viewing orientation, the display has to be rotated 90 
degrees.
Right-click the desktop and select 
Screen resolution from the popup menu. Select Portrait in 
Orientation, and apply the setting.
Depending on the operating system on your PC, different procedures should be followed to adjust the screen 
orientation. Refer to the help document of your operating system for...

  19   How to assemble your monitor hardware
Viewing angle adjustment
You may position the screen to the desired angle with -5° to + 20° monitor tilt, 90° (left and 
right total) monitor swivel, and 150 mm monitor height.
4. Adjust the monitor to the desired viewing 
angle.
-5-5O O ~ +20~ +20O-5O ~ +20O-45-45O O ~ +45~ +45O-45O ~ +45O
150 mm
 

20  How to assemble your monitor hardware  
Using the monitor wall mounting kit
The back of your LCD monitor has a VESA standard mount with 100mm pattern, allowing the 
installation of a wall mount bracket. Before starting to install a monitor wall mounting kit, 
please read the precautions carefully.
Precautions
• Install your monitor and monitor mounting kit on a wall with flat surface.
• Ensure that the wall material is stable to support the weight of the monitor.
• Turn off the monitor and the power...