BenQ Bl2405ht User Manual

  11   How to assemble your monitor hardware
To Connect the HDMI Cable
Connect the plug of the HDMI cable to one of the two 
HDMI ports on the monitor. Connect the other end of 
the cable to the HDMI port of a digital output device.
 If there is more than one video transmission method available 
to you, you might want to take the picture quality of each 
video cable into consideration before making the connection.
- Better quality: HDMI / DVI-D
- Good quality: D-Sub
 The video cables included in your...

12  How to assemble your monitor hardware  
Turn on the monitor by pressing the power button on 
the right of the monitor. 
Turn on the computer too, and follow the instructions 
in Getting the most from your BenQ monitor on page 
22 to install the monitor software.
 To extend the service life of the product, we recommend that 
you use your computers power management function.
 

  13   How to assemble your monitor hardware
How to detach the base
1. Prepare the monitor and area.
Turn off the monitor and the power before unplugging 
the power cable. Turn off the computer before 
unplugging the monitor signal cable.
Protect the monitor and screen by clearing a flat open 
area on your desk and placing a soft item like a towel on 
the desk for padding, before laying the screen face down 
on a flat clean padded surface.
 Please be careful to prevent damage to the monitor. Placing 
the...

14  How to assemble your monitor hardware  
Using the monitor wall mounting kit
The back of your LCD monitor has a VESA standard mount with 100mm pattern, allowing the 
installation of a wall mount bracket. Before starting to install a monitor wall mounting kit, 
please read the precautions carefully.
Precautions:
• Install your monitor and monitor mounting kit on a wall with flat surface.
• Ensure that the wall material is stable to support the weight of the monitor.
• Turn off the monitor and the power...

  15   Assembling your monitor with a height adjustment stand (HAS)
Assembling your monitor with a height adjustment stand 
(HAS)
How to attach the monitor base
• If the computer is turned on you must turn it off before continuing. 
Do not plug-in or turn-on the power to the monitor until instructed to do so.
• The following illustrations are for your reference only. Available input and output jacks may vary depending on 
the purchased model.
 Please be careful to prevent damage to the monitor. Placing...

16  Assembling your monitor with a height adjustment stand (HAS)  
Extend the monitor to the maximum extended position. 
Then tilt the monitor. And rotate the monitor 90 
degrees counterclockwise as illustrated.
You might want to adjust the monitor height. See 
Adjusting the monitor height on page 18 for more 
information.
 You should position the monitor and angle the screen to 
minimize unwanted reflections from other light sources.
-90
-5-5O O ~ +15~ +15O-5O ~ +15O
 

  17   Assembling your monitor with a height adjustment stand (HAS)
How to detach the base
To move the monitor properly, you should extend the monitor to its maximum 
height, then place one hand on the upper part of the monitor stand and the other 
hand on the lower part of the stand as illustrated.
1. Prepare the monitor and area.
Turn off the monitor and the power before unplugging 
the power cable. Turn off the computer before 
unplugging the monitor signal cable.
Gently lift the display up and extend...

18  Assembling your monitor with a height adjustment stand (HAS)  
Adjusting the monitor height
To adjust the monitor height, hold both the left and the 
right sides of the monitor to lower the monitor or lift it 
up to the desired height.
• Avoid placing hands on the upper or lower part of the height-adjustable stand or at the 
bottom of the monitor, as ascending or descending monitor might cause personal 
injuries. Keep children out of reach of the monitor while performing this operation.
• If the...

  19   Assembling your monitor with a height adjustment stand (HAS)
Rotating the monitor
1. Pivot the display.
Before rotating the monitor with a portrait viewing orientation, the display has to be rotated 90 degrees.
Right-click the desktop and select Screen resolution from the popup menu. Select Portrait in 
Orientation, and apply the setting.
 Depending on the operating system on your PC, different procedures should be followed to adjust the screen 
orientation. Refer to the help document of your...

20  Assembling your monitor with a height adjustment stand (HAS)  
Viewing angle adjustment
You may position the screen to the desired angle with -5° to +15° monitor tilt, 90° (left and 
right total) monitor swivel, and 110 mm monitor height.
4. Adjust the monitor to the desired viewing 
angle.
-5-5O O ~ +15~ +15O-5O ~ +15O
-45-45O O ~ +45~ +45O-45O ~ +45O
11 0  m m