BenQ Bl2211tm User Manual

							  11   How to assemble your monitor hardware
How to detach the base
1. Prepare the monitor and area.
Turn off the monitor and the power before unplugging 
the power cable. Turn off the computer before 
unplugging the monitor signal cable.
Protect the monitor and screen by clearing a flat open 
area on your desk and placing a soft item like a towel on 
the desk for padding, before laying the screen face down 
on a flat clean padded surface.
 Please be careful to prevent damage to the monitor. Placing 
the screen surface on an object like a stapler or a mouse will 
crack the glass or damage the LCD substrate voiding your 
warranty. Sliding or scraping the monitor around on your 
desk will scratch or damage the monitor surround and 
controls. 
2. Push the locking clips upward to detach the 
monitor base from the monitor stand arm.
While pushing the locking clips upward, detach the 
stand base from the stand arm.
3. Remove the monitor stand.
Insert a pointed object such as a screwdriver to the 
hole above the monitor stand arm, and then push the 
screwdriver against the release button inside the hole. 
Then pull the monitor stand backward away from the 
monitor.
1
2
1
2
 
						

							12  How to assemble your monitor hardware  
Using the monitor wall mounting kit
The back of your LCD monitor has a VESA standard mount with 100mm pattern, allowing the 
installation of a wall mount bracket. Before starting to install a monitor wall mounting kit, 
please read the precautions carefully.
Precautions:
• Install your monitor and monitor mounting kit on a wall with flat surface.
• Ensure that the wall material is stable to support the weight of the monitor.
• Turn off the monitor and the power before disconnecting the cables from the LCD monitor.
1. Remove the monitor base.
Lay the screen face down on a clean and well-padded 
surface. 
Detach the monitor base as instructed in How to 
detach the base on page 11.
 In case you intend to use your monitor on the stand in the 
future, please keep the monitor base, monitor stand, and 
screws somewhere safe for future use.
2. Follow the instruction manuals of the wall 
mount bracket you purchased to complete 
the installation.
1
2
 
						

							  13   Assembling your monitor with a height adjustment stand (HAS)
Assembling your monitor with a height adjustment stand 
(HAS)
How to attach the monitor base
• If the computer is turned on you must turn it off before continuing. 
Do not plug-in or turn-on the power to the monitor until instructed to do so.
• The following illustrations are for your reference only. Available input and output jacks may vary depending on 
the purchased model.
 Please be careful to prevent damage to the monitor. Placing 
the screen surface on an object like a stapler or a mouse will 
crack the glass or damage the LCD substrate voiding your 
warranty. Sliding or scraping the monitor around on your 
desk will scratch or damage the monitor surround and 
controls.
Protect the monitor and screen by clearing a flat open 
area on your desk and placing a soft item like the 
monitor packaging bag on the desk for padding.
Gently lay the screen face down on a flat clean padded 
surface.
While holding the monitor firmly against the desk, pull 
the monitor stand arm upwards clear of the monitor.
Orient and align the stand base socket with the end of 
the stand arm, then push them together. Tighten the 
thumbscrew on the bottom of the monitor base as 
illustrated. 
Gently attempt to pull them back apart to check that 
they have properly engaged.
Carefully lift the monitor, turn it over and place it 
upright on its stand on a flat even surface.
1
2
3
 
						

							14  Assembling your monitor with a height adjustment stand (HAS)  
Extend the monitor to the maximum extended position. 
Then tilt the monitor. And rotate the monitor 90 
degrees counterclockwise as illustrated.
You might want to adjust the monitor height. See 
Adjusting the monitor height on page 16 for more 
information.
 You should position the monitor and angle the screen to 
minimize unwanted reflections from other light sources.
-90
-5-5O O ~ +15~ +15O-5O ~ +15O
 
						

							  15   Assembling your monitor with a height adjustment stand (HAS)
How to detach the base
To move the monitor properly, you should extend the monitor to its maximum 
height, then place one hand on the upper part of the monitor stand and the other 
hand on the lower part of the stand as illustrated.
1. Prepare the monitor and area.
Turn off the monitor and the power before unplugging 
the power cable. Turn off the computer before 
unplugging the monitor signal cable.
Gently lift the display up and extend the stand to the 
maximum extended position.
Protect the monitor and screen by clearing a flat open 
area on your desk and placing a soft item like a towel on 
the desk for padding, before laying the screen face down 
on a flat clean padded surface.
 Please be careful to prevent damage to the monitor. Placing 
the screen surface on an object like a stapler or a mouse will 
crack the glass or damage the LCD substrate voiding your 
warranty. Sliding or scraping the monitor around on your 
desk will scratch or damage the monitor surround and 
controls. 
2. Release the thumbscrew on the bottom of 
the monitor base and detach the monitor 
base as illustrated.
2
1
3
 
						

							16  Assembling your monitor with a height adjustment stand (HAS)  
Adjusting the monitor height
To adjust the monitor height, hold both the left and the 
right sides of the monitor to lower the monitor or lift it 
up to the desired height.
• Avoid placing hands on the upper or lower part of the height-adjustable stand or at the 
bottom of the monitor, as ascending or descending monitor might cause personal 
injuries. Keep children out of reach of the monitor while performing this operation.
• If the monitor has been rotated to portrait mode and height adjustment is desired, you 
should be noted that the wide screen will keep the monitor from being lowered to its 
minimum height.
 
						

							  17   Assembling your monitor with a height adjustment stand (HAS)
Rotating the monitor
1. Pivot the display.
Before rotating the monitor with a portrait viewing orientation, the display has to be rotated 90 degrees.
Right-click the desktop and select Screen resolution from the popup menu. Select Portrait in 
Orientation, and apply the setting.
 Depending on the operating system on your PC, different procedures should be followed to adjust the screen 
orientation. Refer to the help document of your operating system for details.
2. Fully extend the monitor and tilt it.
Gently lift the display up and extend it to the maximum 
extended position. Then tilt the monitor.
 The monitor should be vertically extended to allow the 
monitor to rotate from landscape to portrait mode. 
3. Rotate the monitor 90 degrees clockwise as 
illustrated. 
 To avoid the edge of the LCD display hitting the monitor base 
surface while it is being rotated, do tilt and extend the monitor 
to the highest position before you start to rotate the display. 
You should also make sure there are no obstacles around the 
monitor and there is enough room for cables. You might need 
to route the cables again via the cable clip after the rotation.
90
 
						

							18  Assembling your monitor with a height adjustment stand (HAS)  
Viewing angle adjustment
You may position the screen to the desired angle with -5° to +15° monitor tilt, 90° (left and 
right total) monitor swivel, and 110 mm monitor height.
4. Adjust the monitor to the desired viewing 
angle.
-5-5O O ~ +15~ +15O-5O ~ +15O
-45-45O O ~ +45~ +45O-45O ~ +45O
11 0  m m
 
						

							  19   Assembling your monitor with a height adjustment stand (HAS)
Using the monitor wall mounting kit
The back of your LCD monitor has a VESA standard mount with 100mm pattern, allowing the 
installation of a wall mount bracket. Before starting to install a monitor wall mounting kit, 
please read the precautions carefully.
Precautions:
• Install your monitor and monitor mounting kit on a wall with flat surface.
• Ensure that the wall material is stable to support the weight of the monitor.
• Turn off the monitor and the power before disconnecting the cables from the LCD monitor.
1. Remove the monitor base.
Lay the screen face down on a clean and well-padded 
surface. Detach the monitor base as instructed in How to 
detach the base on page 15.
2. Remove the monitor stand.
Use a a cross-pointed screwdriver to release the screws 
that fixing the monitor stand to the monitor.The use of a 
magnetic-head screwdriver is recommended to avoid of 
losing the screws.
Then pull the monitor stand backward away from the 
monitor.
 In case you intend to use your monitor on the stand in the 
future, please keep the monitor base, monitor stand, and 
screws somewhere safe for future use.
3. Follow the instruction manuals of the wall 
mount bracket you purchased to complete 
the installation.
 
						

							20  Getting the most from your BenQ monitor  
Getting the most from your BenQ monitor
To gain the most benefit from your new BenQ LCD monitor, you should install the custom 
BenQ LCD Monitor driver software as provided on the BenQ LCD Monitor CD-ROM.
The circumstances under which you connect and install your BenQ LCD Monitor will 
determine which process you need to follow to successfully install the BenQ LCD Monitor 
driver software. These circumstances relate to which version of Microsoft Windows you are 
using, and whether you are connecting the monitor and installing the software onto a new 
computer (without existing monitor driver software), or whether you are upgrading an existing 
installation (which already has existing monitor driver software) with a newer monitor. 
In either case however, the very next time you turn on your computer (after connecting the 
monitor to your computer), Windows will automatically recognize the new (or different) 
hardware, and will launch its 
Found New Hardware wizard. 
Follow the wizard instructions until it asks you to select a monitor model. At that point, click 
the 
Have Disk button, insert the BenQ LCD Monitor CD-ROM and select the appropriate 
monitor model. Further details and step-by-step instructions for either an automatic (new) or 
upgrade (existing) installation, see:
• How to install the monitor on a new computer on page 21.
• How to upgrade the monitor on an existing computer on page 22.
• If you require a User Name and Password to login to your Windows computer, you must be logged on as an 
Administrator or as a member of the Administrators group in order to install the monitor driver software. 
Furthermore, if your computer is connected to a network which has security access requirements, network 
policy settings may prevent you from installing software on your computer.
• To check the name of the purchased model, refer to the specification label on the back of the monitor.