Home > Bench > Projector > Bench Mx750/mp780st Digital Projector User Manual

Bench Mx750/mp780st Digital Projector User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Bench Mx750/mp780st Digital Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1 Bench manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Troubleshooting 91
    Troubleshooting
    The projector does not turn on.
    No picture
    Blurred image
    Remote control does not work
    The password is incorrect
    CauseRemedy
    There is no power from the power 
    cable.Plug the power cord into the AC inlet on the 
    projector, and plug the power cord into the 
    power outlet. If the power outlet has a switch, 
    make sure that it is switched on.
    Attempting to turn the projector on 
    again during the cooling process.Wait until the cooling down process has 
    completed.
    CauseRemedy
    The video source is not turned on or 
    connected correctly.Turn the video source on and check that the 
    signal cable is connected correctly.
    The projector is not correctly 
    connected to the input signal device.Check the connection.
    The input signal has not been 
    correctly selected.Select the correct input signal with the 
    SOURCE key on the projector or remote 
    control.
    The lens cover is still closed. Open the lens cover.
    CauseRemedy
    The projection lens is not correctly 
    focused.Adjust the focus of the lens using the focus 
    ring.
    The projector and the screen are not 
    aligned properly.Adjust the projection angle and direction as 
    well as the height of the unit if necessary.
    The lens cover is still closed. Open the lens cover.
    CauseRemedy
    The battery is out of power. Replace the battery with new one.
    There is an obstacle between the 
    remote control and the projector.Remove the obstacle.
    You are too far away from the 
    projector.Stand within 8 meters (26 feet) of the 
    projector.
    CauseRemedy
    You do not remember the password.Please see Entering the password recall 
    procedure on page 35 for details. 
    						
    							Specifications 92
    Specifications
    All specifications are subject to change without notice. 
    Optical
    Resolution
    (MX750)
    1024 x 768 XGA
    (MP780 ST)
    1280 x 800 WXGA
    Display system
    1-CHIP DMD
    Lens F/Number
    (MX750)
    F = 2.68 to 3.4, 
    f = 15.94 to 25.5 mm
    (MP780 ST)
    F = 2.89, 
    f = 7.78 mm
    Lamp
    (MX750)
    225 W lamp
    (MP780 ST)
    185 W lamp
    Electrical
    Power supply
    AC100–240V, 3.20 A,
    50-60 Hz (Automatic)
    Power consumption
    (MX750)
    300 W (Max.)
    (MP780 ST)
    260 W (Max.)
    Mechanical
    We i g h t
    (MX750)
    3.6 kg (7.9 lbs.)
    (MP780 ST)
    3.7 kg (8.1 lbs.)
    Output terminals
    RGB output
    D-Sub 15-pin (female) x 1
    Speaker
    (Stereo) 10 watt x 2
    Audio signal output
    PC audio jack x 1
    Control
    RS-232 serial control 
    9 pin x 1
    LAN controk
    RJ45 x 1 (wired)
    USB A type x 2 (wireless)
    Screen control
    12V trigger x 1 (0.5 A)
    USB B type x 1
    (Supports firmware upgrade)
    Input terminals
    Computer input
    RGB input
    D-Sub 15-pin (female) x 2
    Video signal input
    S-VIDEO
    Mini DIN 4-pin port x 1
    VIDEO
    RCA jack x 1
    SD/HDTV signal input
    Analog - Component RCA jack x 3
       (through RGB input)
    Digital-HDMI V1.3 x 1
    Audio signal input
    Audio in
    PC audio jack x 1
    RCA audio jack (L/R) x 2
    USB A type x 2
    (Supports mouse/keyboard/card reader)
    USB mini-B type x 1
    (Supports USB display)
    Environmental Requirements
    Operating temperature
    0°C-40°C at sea level
    Operating relative humidity
    10%-90% (without condensation)
    Operating altitude
    0-1499 m at 0°C-35°C
    1500-3000 m at 0°C-30°C (with High Alti-
    tude Mode on) 
    						
    							Specifications 93
    Dimensions
    329 mm (W) x 137.2 mm (H) x 241.9 mm (D)
    Ceiling mount installation
    329
    241.9
    137.2
    62.577.4
    75.0
    221.0
    100.00
    116.00
    82.50
    107.7
    328.0 163.762.5115.1129.1
    100.0
    146.0
    Ceiling mount screws:
    M4 x 8 (Max. L = 8 mm)
    Unit: mm 
    						
    							Specifications 94
    Timing chart
    Supported timing for PC input
    ResolutionHorizontal 
    Frequency 
    (kHz)Ve r t i ca l  
    Frequency 
    (Hz)Pixel 
    Frequency 
    (MHz)Mode
    720 x 400 31.469 70.087 28.322 720 x 400_70
    640 x 480 31.469 59.940 25.175 VGA_60
    37.500 75.000 31.500 VGA_75
    43.269 85.008 36.000 VGA_85
    800 x 600 37.879 60.317 40.000 SVGA_60
    48.077 72.188 50.000 SVGA_72
    46.875 75.000 49.500 SVGA_75
    53.674 85.061 56.250 SVGA_85
    1024 x 768 48.363 60.004 65.000 XGA_60
    56.476 70.069 75.000 XGA_70
    60.023 75.029 78.750 XGA_75
    68.677 84.997 94.500 XGA_85
    1024 x 576 35.820 60.0 46.996 Netbook_1
    1024 x 600 37.5 60.0 45.000 Netbook_2
    1024 x 600 41.467 64.995 51.419 Netbook_3
    1280 x 800 49.702 59.810 83.500 WXGA_60
    62.795 74.934 106.500 WXGA_75
    71.554 84.880 122.500 WXGA_85
    1280 x 1024 63.981 60.020 108.000 SXGA_60
    79.976 75.025 135.000 SXGA_75
    91.146 85.024 157.500 SXGA_85
    1280 x 960 60.000 60.000 108 1280 x 960_60
    85.938 85.002 148.500 1280 x 960_85
    1440 x 900 55.935 59.887 106.500 WXGA+_60
    1400 x 1050 65.317 59.978 121.750 SXGA+_60
    1600 x 1200 75.000 60.000 162.000 UXGA
    640 x 480
    @67Hz35.000 66.667 30.240 MAC13
    832 x [email protected] 74.546 57.280 MAC16
    1024 x [email protected] 75.020 80.000 MAC19
    1152 x [email protected] 75.060 100.000 MAC21 
    						
    							
    Specifications 95
    Supported timing for HDMI input
    Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image 
    vibration.
    ResolutionHorizontal 
    Frequency 
    (kHz)Ve r ti ca l  
    Frequency 
    (Hz)Pixel 
    Frequency 
    (MHz)Mode
    720 x 400 31.469 70.087 28.322 720 x 400_70
    640 x 480 31.469 59.940 25.175 VGA_60 37.861 72.809 31.500 VGA_72
    37.500 75.000 31.500 VGA_75
    43.269 85.008 36.000 VGA_85
    800 x 600 37.879 60.317 40.000 SVGA_60 48.077 72.188 50.000 SVGA_72
    46.875 75.000 49.500 SVGA_75
    53.674 85.061 56.250 SVGA_85
    1024 x 768 48.363 60.004 65.000 XGA_60 56.476 70.069 75.000 XGA_70
    60.023 75.029 78.750 XGA_75
    68.677 84.997 94.500 XGA_85
    1280 x 800 49.702 59.810 83.500 WXGA_60
    62.795 74.934 106.500 WXGA_75
    71.554 84.880 122.500 WXGA_85
    1280 x 1024 63.981 60.020 108.000 SXGA_60
    79.976 75.025 135.000 SXGA_75
    91.146 85.024 157.500 SXGA_85
    1280 x 960 60.000 60.000 108 1280 x 960_60 85.938 85.002 148.500 1280 x 960_85
    1440 x 900 55.935 59.887 106.500 WXGA+_60
    1400 x 1050 65.317 59.978 121.750 SXGA+_60
    1600 x 1200 75.000 60.000 162.000 UXGA
    640 x 480
    @67Hz35.000 66.667 30.240 MAC13
    832 x [email protected] 74.546 57.280 MAC16
    1024 x [email protected] 75.020 80.000 MAC19
    1152 x [email protected] 75.060 100.000 MAC21
    VIDEO
    (HDCP) 31.47 60 27 480p
    31.25 50 27 576p
    45.00 60 74.25 720p_60
    37.50 50 74.25 720_50
    33.75 60 74.25 1080i_60
    28.13 50 74.25 1080i_50
    67.5 60 148.5 1080p
    56.25 50 148.5 1080p 
    						
    							Specifications 96
    Supported timing for Component-YPbPr input
    Displaying a 1080i@60Hz or 1080i@50Hz signal may result in slight image vibration.
    Supported timing for Video and S-Video inputs
    Signal FormatHorizontal Frequency 
    (kHz)Vertical Frequency (Hz)
    480i(525i)@60Hz 15.73 59.94
    480p(525p)@60Hz 31.47 59.94
    576i(625i)@50Hz 15.63 50.00
    576p(625p)@50Hz 31.25 50.00
    720p(750p)@60Hz 45.00 60.00
    720p(750p)@50Hz 37.50 50.00
    1080i(1125i)@60Hz 33.75 60.00
    1080i(1125i)@50Hz 28.13 50.00
    1080p@60Hz 67.5 60.00
    1080p@50Hz 56.25 50.00
    Video modeHorizontal 
    Frequency (kHz)Ver t ic al  
    Frequency (Hz)Color sub-carrier 
    Frequency (MHz)
    NTSC 15.73 60 3.58
    PAL 15.63 50 4.43
    SECAM 15.63 50 4.25 or 4.41
    PAL-M 15.73 60 3.58
    PAL-N 15.63 50 3.58
    PAL-60 15.73 60 4.43
    NTSC4.43 15.73 60 4.43 
    						
    							Warranty and Copyright information 97
    Warranty and Copyright information
    Patents for MP780 ST
    This BenQ projector is covered by the following patents:
    U.S. patents 6,837,608; 7,275,834; 7,181,318; TW patents 202690; 205470; I228635; I259932; 
    China Patents (中国发明专利) ZL01143168.7; ZL03119907.0; ZL200510051609.2
    Limited warranty
    BenQ warrants this product against any defects in material and workmanship, under normal 
    usage and storage.
    Proof of purchase date will be required with any warranty claim. In the event this product is 
    found to be defective within the warranty period, BenQs only obligation and your exclusive 
    remedy shall be replacement of any defective parts (labor included). To obtain warranty 
    service, immediately notify the dealer from which you purchased the product of any defects.
    Important: The above warranty shall be void if the customer fails to operate the product in 
    accordance with BenQs written instructions, especially the ambient humidity must be in-
    between 10% and 90%, temperature in-between 0°C and 35°C, altitude lower than 4920 
    feet, and avoiding to operate the projector in a dusty environment. This warranty gives you 
    specific legal rights, and you may have other rights which vary from country to country.
    For other information, please visit www.BenQ.com.
    Copyright
    Copyright 2010 by BenQ Corporation. All rights reserved. No part of this publication may 
    be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any 
    language or computer language, in any form or by any means, electronic, mechanical, 
    magnetic, optical, chemical, manual or otherwise, without the prior written permission of 
    BenQ Corporation.
    Disclaimer
    BenQ Corporation makes no representations or warranties, either expressed or implied, 
    with respect to the contents hereof and specifically disclaims any warranties, merchantability 
    or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise 
    this publication and to make changes from time to time in the contents hereof without 
    obligation to notify any person of such revision or changes.
    *DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others 
    are copyrights of their respective companies or organizations. 
    						
    							Regulation statements 98
    Regulation statements
    FCC statement
    CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not 
    installed and used in accordance with the instructions, may cause harmful interference to 
    radio communications. However, there is no guarantee that interference will not occur in a 
    particular installation. If this equipment does cause harmful interference to radio or 
    television reception, which can be determined by turning the equipment off and on, the user 
    is encouraged to try to correct the interference by one or more of the following measures:
    — Reorient or relocate the receiving antenna.
    — Increase the distance between the equipment and receiver.
    — Connect the equipment into an outlet on a circuit different from that to which the 
    receiver is connected.
    — Consult the dealer or an experienced radio/TV technician for help.
    FCC/IC statement
    This device complies with Part 15 of the FCC Rules/RSS-210. Operation is subject to the 
    following two conditions: (1) This device may not cause harmful interference, and (2) this 
    device must accept any interference received, including interference that may cause 
    undesired operation.
    FCC Caution: Any changes or modifications not expressly approved by the party responsible 
    for compliance could void the users authority to operate this equipment.
    Canada
    This Class B digital apparatus complies with Canadian ICES-003.
    Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
    EEC statement (for European users)
    This device complies with the requirements set out in the Council Directives on the 
    Approximation of the Laws of the Member States relating Electromagnetic Compatibility 
    (2004/108/EC) , Low Voltage Directive (2006/95/EC), the Restriction of The Use of Certain 
    Hazardous Substances in Electrical And Electronic Equipment Directive (2002/95/EC), 
    Turkish EEE Directive, Commission Regulation (EC) No 1275/2008 implementing Directive 
    2005/32/EC of the European Parliament and of the Council with regard to ecodesign 
    requirements for standby and off mode electric power consumption of electrical and 
    electronic household and office equipment, and the Directive 2009/125/EC of the European 
    parliament and of the council establishing a framework for the setting of ecodesign 
    requirements for energy-related products.
    WEEE directive
    Disposal of Waste Electrical and Electronic Equipment by users in private households 
    in the European Union.
    This symbol on the product or on the packaging indicates that this can 
    not be disposed of as household waste. You must dispose of your waste 
    equipment by handling it over to the applicable take-back scheme for the 
    recycling of electrical and electronic equipment. For more information 
    about recycling of this equipment, please contact your city office, the shop 
    where you purchased the equipment or your household waste disposal 
    service. The recycling of materials will help to conserve natural resources 
    and ensure that it is recycled in a manner that protects human health and 
    environment.
       
    						
    							Regulation statements 99
    Accessibility Requirements for Rehabilitation Act of 1973, Section
    508
    BenQ’s commitment to accessible products allows us to support government in making 
    accessible technology choices BenQ’s LCD monitors and projectors are compliant with 
    Section 508 guidelines by including the assistive features as below:
    • BenQ’s monitors have colored “Power” indicators. While the indicator shows green, it means that 
    the monitor is using the full power. While the indicator shows yellow or amber, it means that the 
    monitor is in suspend or sleep mode and is using less than 2 watts of electricity.
    • BenQ’s monitors have a variety of settings of pre-programmed flicker-free timing to make the 
    screen shown on the monitor readily accessible. The default timing setting is automatically turned 
    on every time the monitor is powered up, and thus reduces the hassle of user intervention.
    • BenQ’s monitors and projectors have options for brightness and contrast adjustments that text 
    and images could be displayed differently to meet the demands of the visually impaired.  Other 
    similar adjustments are also available by using the On-Screen Display (OSD) controls on the 
    products.
    • BenQ’s monitors and projectors include user-selectable color controls, such as color temperature 
    selections (Monitor: 5800K, 6500K and 9300K, Projector: 5500K, 6500K, 7500K and 9300K), with 
    a wide range of contrast levels.
    • BenQ’s multimedia monitors and projectors usually have one or two speakers for audio 
    performance which allow users (including hearing impaired) to interact with the computer 
    systems connected. Speaker controls are typically located on the front-panel. 
    • Firmware of BenQ’s monitors and projectors contain unique product information that helps 
    computer systems to identify BenQ products and activate their Plug-and-Play function when 
    connected.
    • All BenQ’s monitors and projectors are compatible with the PC99 standard. For example, 
    connectors are color-coded to help users easily connecting products to computer systems 
    correctly.
    • Some models of  BenQ’s monitors and projectors contain additional USB and DVI ports for 
    connection to more devices such as a special headphone to assist the hearing impaired.
    • All BenQ monitors and projectors come with user manuals on compact discs which could be 
    easily read by commercial software such as Adobe Reader via a connected computer system.  
    These documents are also available on the BenQ’s web site (www.BenQ.com ).  Other types of documents may be available upon requests.
    • BenQ’s customer service provides answers and assistance to all our customers through phone 
    calls, facsimiles, e-mails, or web sites. 
    						
    All Bench manuals Comments (0)