Belkin Router Surf Wireless User Manual

11
GeTTI nG  sT aRTeD
adding Computers to Your  network
Wireless devices such as computer s, net work printer s, and gaming systems can connect to your Router with a few simple steps  .
Using the CD
1 . Put the Setup CD into your computer  . If the CD doesn’t open automatically, browse to your CD drive and open the Belkin Setup CD icon  .
2 . Click the Setup icon on the CD menu  .
3 . After a brief installation, the setup software will ask you for the net work name and password from the net work...

12
GeTTI nG  sT aRTeD
Manually
If you choose not to use the included Setup CD for adding additional computer s or wireless devices, you can manually add these items to your network  .
1 . Locate the wireless- net work- connections option on your computer or wireless device  .
2 . Select your Belk in Router from the list of available net works  . You can identif y your Belk in Router by locating the net work name (SSID) from the card located underneath the foot of your Router  .
3 . Enter your net work...

13
GeTTI nG TO Kn OW YOUR R OUTeR
a ) Router  status  light
Your Router’s status is shown by the light on the front .
Off: The Router is not plugged into a power source  .
blinking Green: The Router is starting up  .
solid Green: The Router is connected to the Internet .
b linking  amber: The Router can’t detect the modem  . Either the modem is off, is not plugged into the Router, or is unresponsive  .
b)  
Wi- fi Protected  setup (WP s)  light and  button
The WPS button on the front of your Router can...

14
GeTTI nG TO Kn OW YOUR R OUTeR
a ) Modem (W an) Connector
Connect your modem to this port using an Ethernet cable  .
b) Wired ( lan) Connectors
Connect computers and other wired network devices to these ports using Ethernet cables  .
C) Reset button
This button is used to restart your Router in rare cases when it functions incorrectly  . Resetting the Router will preserve your settings  . This button may also be used to restore the factory default settings  . Please see the Troubleshooting section for...

15
TeCHn ICal De Ta Ils
Technical  features
Integrated 802  .11n Wireless  access PointThe N150 technology enhances your Router ’s wireless capabilities, allowing for data transfer speeds of up to 150Mbps across your network  .
naT IP  address  sharingTo save you the cost of adding IP addresses per computer in your house, your Belk in Router uses Net work Address Translation (NAT) technology, allowing you to share a single IP address across your network  .
sPI  firewallYour Router is equipped with a...

16
TeCHn ICal De Ta Ils
s ystem Requirements
Router 
Broadband Internet connection such as a cable or DSL modem with RJ45 (Ethernet) connection
At least one computer with an installed network interface adapter
TCP/IP networking protocol installed on each computer
RJ45 Ethernet networking cable
Internet browser
s etup  software
A computer running Windows® XP SP2 and higher,  Windows Vista® 32 and 64 bit, or  Windows 7 32 and 64 bit;  or Mac OS® X, 10  .5 and 10  .6
Minimum 1GHz processor and 256MB RAM...

17
TROUbles HOOTInG, sUPPORT , anD Wa RRanTY
Troubleshooting
The  setup CD does not automatically start  .
If Belk in Setup does not run when you inser t the CD - ROM, your computer may not be configured to open CDs automatically  .
If Belk in Setup does not appear within 15 seconds, browse to your CD - ROM drive and open the “ Belk in Setup” icon . Alternatively, you may visit http://router/ and per form the setup manually . Please see “ Manual Setup Using Your Browser” earlier in this manual for more...

18
TROUbles HOOTInG, sUPPORT , anD Wa RRanTY
belkin  setup cannot connect my Router to the Internet  .
If Belk in Setup is not able to connect the Router to the Internet, please check the following items:
1 . Use the troubleshooting suggestions within Belkin Setup  .
2 . If your ISP requires a user name and password, make sure that you have t yped in your user name and password correctly  . Some user names require that the ISP ’s domain may be at the end of the name  . E xample: “ myname@myisp  .com”  ....

19
TROUbles HOOTInG, sUPPORT , anD Wa RRanTY
belkin  setup  complete d  inst allat ion,  but  I  cannot  browse  the Web  . The light on the front of my Router is solid amber  .
1 . Use the troubleshooting suggestions within Belkin Setup  .
2 . If your ISP requires a user name and password, make sure that you have t yped in your user name and password correctly  . Some user names require that the ISP ’s domain may be at the end of the name  . E xample: “ myname@myisp  .com”  . The “@myisp  .com” par t of...

20
TROUbles HOOTInG, sUPPORT , anD Wa RRanTY
I  can’t  conne c t  to  the  Internet  wirelessly  and  my network name is not listed in  available  networks  .
1 . Verif y that your Router is on and the front-panel light shows solid green  .
2 . If you are far from the Router, you might try moving closer to see if you might have been out of range  .
3 . Using a computer at tached to the Router via a net work cable, visit http://router/ and ensure that “ Broadcast SSID ” is ON  . This setting is found on...