Belkin Router F9K1107 User Manual

							9
USING YOUR ROUTER
Resetting the Router
Reset Button 
The “Reset” button is used in rare cases when the Router may function improperly. Resetting the Router will restore the Router’s normal operation while maintaining the programmed settings. You can also restore the factory default settings by using the “Reset” button. Use the restore option in instances where you may have forgotten your custom password. 
Resetting the Router
Push and release the “Reset” button. The lights on the Router will momentarily flash. The “Router” light will begin to blink. When the “Router” light becomes solid again, the reset is complete. 
Restoring Your Router to Factory Defaults 
Press and hold the “Reset” button for at least 5 seconds, and then release it. The lights on the Router will momentarily flash. The “Router” light will begin to blink. When the “Router” light becomes solid again, the restore is complete.
10. Click the “Update” button.
11. A prompt asking, “Are you sure you want to continue with upgrading?” will appear. Click “OK.”
12. A second prompt will open telling you the Router will not respond during the upgrade and warning you not to remove the power supply from the Router. Click “OK” once more.
Congratulations. The firmware has been updated successfully.  
						

							10
USING YOUR ROUTER
5. Click on the “Restore Defaults” button.
4.  Click on “Restore Factory Defaults” in the left-hand column  under the “Utilities” heading.Restoring the Router to Default Settings Using the Web Interface 
Symptoms
You need to restore the factory defaults using the web interface. This may be because the Router is not performing as expected or you wish to remove all previously configured settings.
Setup steps
1.  Open a web browser on the computer.
2.  In the address bar of the web browser, type “http://192.168.2.1”.
3. Click “Login” in the upper right-hand corner of the page. The Router does not ship with a password, so just click “Submit.”  
						

							11
USING YOUR ROUTER
7.  The Router will begin the restoring process. Once the restore  is complete, the Router will reboot.  
Note: This may take several minutes.
Your Router has successfully been restored to its factory settings.
6.  A warning box will open that says, “Warning: All your settings will be lost. Are you sure you want to do this?” Click “OK.”  
						

							12
Troubleshooting
I can’t connect to the Internet wirelessly .
If the light on the front of the Router is solid blue, then your Router is connected to the Internet. You may not be connected to the Router’s wireless network. Please refer to “Adding Computers to Your Network” in this manual for instructions. If your Windows XP computer is running SP2, you will not be able to set up the Router via the wireless setup process. You will need to either update to Windows XP SP3 or complete the setup via a wired connection.
TROUBLESHOOTING, SUPPORT, AND WARRANTY 
My wireless network performance is slow, inconsistent, suffers from weak signal, or I’m having difficulty maintaining a VPN connection .
Wireless technology is radio-based, which means connectivity and the throughput performance between devices decreases when the distance between devices increases. Other factors that will cause signal degradation (metal is generally the worst culprit) are obstructions such as walls and metal appliances. Note also that connection speed may decrease as the computer moves farther away from the Router. In order to determine if wireless issues are related to range, we suggest temporarily moving the computer within 10 feet from the Router if possible.
Changing the wireless channel
Depending on local wireless traffic and interference, switching the wireless channel of your network can improve performance and reliability.   
						

							13
TROUBLESHOOTING, SUPPORT, AND WARRANTY 
Limiting the wireless transmit rate
Limiting the wireless transmit rate can help improve range and connection stability. Most wireless cards have the ability to limit the transmission rate. To change this property in Windows, go to the Windows Control Panel, open “Network Connections,” and double-click on your wireless card’s connection. In the properties dialog, select the “Configure” button on the “General” tab, then choose the “Advanced” tab and select the rate property. Wireless client cards are usually set to automatically adjust the wireless transmit rate for you, but doing so can cause periodic disconnects when the wireless signal is too weak; as a rule, slower transmission rates are more stable. Experiment with different connection rates until you find the best one for your environment. Note that all available transmission rates should be acceptable for browsing the Internet. For more assistance, see your wireless card’s user manual.
Does the Router support Wireless Protected Access  (WPA) security?
The Router ships with WPA/WPA2 security turned on. Windows XP and some older network hardware may require a software update to support WPA/WPA2. 
I am having difficulty setting up WPA security on my Router .
1. Log in to your Router by visiting http://router/ with your web browser. Click on the “Login” button in the top right-hand corner of the screen. You will be asked to enter your password. If you have never set a password, leave the “Password” field blank and click “Submit.” 
2.  Click “Wireless” in the left-hand menu. Then click “Security”  just below that.
3. Select the “WPA / WPA2” option.
4. Enter a password. This can be from 8 – 63 characters of your choice, including spaces and punctuation, OR a 64-digit hexadecimal number (using only the numbers 0–9 and letters A–F).
5. Click “Apply Changes” to finish. Your wireless connection is now encrypted. Each computer using your wireless network will need to use the new key.
Note: If you are configuring the Router over a wireless connection, you will have to re-connect to the Router after changing any security settings.
Note: Some older networking hardware supports only WEP encryption. If your older computers cannot connect to your network, try 128-bit or 64-bit WEP, or seek software updates from their manufacturers.  
						

							14
TROUBLESHOOTING, SUPPORT, AND WARRANTY 
I am having difficulty setting up Wired Equivalent Privacy (WEP) security on my Router .
1. Log in to your Router. Visit http://router/ with your web browser. Click on the “Login” button in the top right-hand corner of the screen. You will be asked to enter your password. If you have never set a password, leave the “Password” field blank and click “Submit.”
2.  Click “Wireless” in the left-hand menu. Then click “Security” just below that.
3.  Select the “128-bit WEP ” option.
4. You may type in a WEP key manually, or generate one from a passphrase. Type a phrase in the “Passphrase” field and click the “Generate” button. A WEP key is composed of 26 hexadecimal digits (0 –9, A–F. For example, C3 03 0F AF 4B B2 C3 D4 4B C3 D4 EE 74 is a valid 128-bit WEP key.
5. Click “Apply Changes” to finish. Your wireless activity is now encrypted. Each computer using your wireless network will need to use the new key.
Note: If you are configuring the Router over a wireless connection, you will have to re-connect to the Router after changing any security settings.
Note: Some older networking hardware supports only 64-bit WEP encryption. If your older computers cannot connect to your network, try 64-bit WEP.  
						

							15
TROUBLESHOOTING, SUPPORT, AND WARRANTY 
Technical Support
UShttp://www.belkin.com/support
UKhttp://www.belkin.com/uk/support
Australiahttp://www.belkin.com/au/support 
New Zealandhttp://www.belkin.com/au/support
Singapore1800 622 1130
Europehttp://www.belkin.com/uk/support   
						

							16
TROUBLESHOOTING, SUPPORT, AND WARRANTY 
What is not covered by this warranty?All above warranties are null and void if the Belkin product is not provided to Belkin for inspection upon Belkin’s request at the sole expense of the purchaser, or if Belkin determines that the Belkin product has been improperly installed, altered in any way, or tampered with. The Belkin Product Warranty does not protect against acts of God such as flood, lightning, earthquake, war, vandalism, theft, normal-use wear and tear, erosion, depletion, obsolescence, abuse, damage due to low voltage disturbances (i.e. brownouts or sags),  non-authorized program, or system equipment modification  or alteration.
How to get service   To get ser vice for your Belkin product you must take the  following steps:
1.  Contact Belkin International, Inc., at 12045 E. Waterfront Drive, Playa Vista, CA 90094, Attn: Customer Ser vice, or call 800-223-5546, within 15 days of the Occurrence. Be prepared to provide the following information:
 a. The part number of the Belkin product.
 b. Where you purchased the product.
 c. When you purchased the product.
 d. Copy of original receipt.
2.  Your Belkin Customer Service Representative will then instruct you on how to forward your receipt and Belkin product and how to proceed with your claim.
Belkin International, Inc . , Limited 2-Year Product Warranty
What this warranty covers  .Belkin International, Inc. (“Belkin”) warrants to the original purchaser of this Belkin product that the product shall be free of defects in design, assembly, material, or workmanship. 
What the period of coverage is  .Belkin warrants the Belkin product for two years.
What will we do to correct problems? Product Warranty.Belkin will repair or replace, at its option, any defective product free of charge (except for shipping charges for the product). Belkin reserves the right to discontinue any of its products without notice, and disclaims any limited warranty to repair or replace any such discontinued products. In the event that Belkin is unable to repair or replace the product (for example, because it has been discontinued), Belkin will offer either a refund or a credit toward the purchase of another product from Belkin.com in an amount equal to the purchase price of the product as evidenced on the original purchase receipt as discounted by its natural use.  
						

							17
TROUBLESHOOTING, SUPPORT, AND WARRANTY 
Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
IN NO EVENT SHALL BELKIN BE LIABLE FOR INCIDENTAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS, BUT NOT LIMITED TO, LOST BUSINESS OR PROFITS ARISING OUT OF THE SALE OR USE OF ANY BELKIN PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 
This warranty gives you specific legal rights, and you may also have other rights, which may vary from state to state. Some states do not allow the exclusion or limitation of incidental, consequential, or other damages, so the above limitations may not apply to you.
Belkin reserves the right to review the damaged Belkin product. All costs of shipping the Belkin product to Belkin for inspection shall be borne solely by the purchaser. If Belkin determines, in its sole discretion, that it is impractical to ship the damaged equipment to Belkin, Belkin may designate, in its sole discretion, an equipment repair facility to inspect and estimate the cost to repair such equipment. The cost, if any, of shipping the equipment to and from such repair facility and of such estimate shall be borne solely by the purchaser. Damaged equipment must remain available for inspection until the claim is finalized. Whenever claims are settled, Belkin reserves the right to be subrogated under any existing insurance policies the purchaser may have. 
How state law relates to the warranty
THIS WARRANTY CONTAINS THE SOLE WARRANTY OF BELKIN. THERE ARE NO OTHER WARRANTIES, EXPRESSED OR, EXCEPT AS REQUIRED BY LAW, IMPLIED, INCLUDING THE IMPLIED WARRANTY OR CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND SUCH IMPLIED WARRANTIES, IF ANY, ARE LIMITED IN DURATION TO THE TERM OF THIS WARRANTY.    
						

							18
REGULATORY INFORMATION
FCC Statement
DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITYWe, Belkin International, Inc., of 12045 E. Waterfront Drive, Playa Vista, CA 90094, declare under our sole responsibility that the device, F 9 K110 7, complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.   
Caution: Exposure to Radio Frequency RadiationThe device shall be used in such a manner that the potential for human contact normal operation is minimized.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
•	 Reorient	or 	relocate 	the 	receiving 	antenna. 	
•	 Increase 	the 	distance 	between 	the 	equipment 	and 	the 	receiver. 	
•		
Connect 	the 	equipment 	to 	an 	outlet 	on 	a 	circuit 	different 	from that to which the receiver is connected. 
•	 Consult 	the 	dealer 	or 	an 	experienced 	radio/TV 	technician 	for 	help.
 
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.